SDMC NP1835GRF AX1800 Dual Band WiFi6 CATV GPON Terminal Installation Guide
- June 15, 2024
- SDMC
Table of Contents
SDMC NP1835GRF AX1800 Dual Band WiFi6 CATV GPON Terminal
Package content
- NP1835GRF x 1
- Ethernet Cable x 1
- Power Adapter x 1
- Quick Installation Guide x 1
Ports and indicators
Hardware connections
- Connect a fiber optic cable to the PON port.
- Connect a computer to the GE port using the Ethernet cable (optional).
- Connect a telephone to the TEL port using the PHONE cable (optional)
- Use the included power adapter to connect the power socket to a power outlet. Press the ON/OFF button to turn on the device.
- Connect a STB or TV to the RF port using the coax cable.
WiFi /WiFi6 connection
-
Using SSID
Use the SSID and Wireless Key on the device label to connect wireless to the device. On your smartphone or notebook, find this SSID. Enter the Wireless Key to connect. -
Using WPS
Press the WPS button on the device and the WPS indicator will blink. Then press the WPS button on the client. If the WPS method fails, use the SSID and wireless key to set up a WiFi connection.
Configure on the web
Open a web browser and go to http:@//192.168.1.1 Enter the default User Name and Login Password, and then click Login. Then can configure it on the web page.
LED indicator explanation
| Name | State | Description |
|---|---|---|
| Power | On | The device has been turned on. |
| Off | The device has not been turned on. | |
| LOS | Blinking | No optical signal is detected. |
| Off | Optical signal is detected. | |
| PON | On | The device has been registered. |
| Blinking | Optical signal is detected. | |
| Off | No optical signal is detected. | |
| INTER NET | On | In Routing mode and WAN connection is up. |
| Blinking | Attempt to get an IP address. | |
| INTER NET | Off | No internet connection or the modem router is operating in |
Bridge mode
WIFI| On| Wi-Fi has been turned on
Blinking| Wi-Fi data is being transmitted.
Off| Wi-Fi has been shut down.
WPS| On| The device is successfully connected through WPS function.
Blinking| The device is being connected through WPS function.
Off| The WPS function is not enabled, or the device is successfully connected
through WPS function.
TEL| On| The VOIP server has been registered.
Blinking| The voice service is in use.
Off| The VOIP server is not registered.
CATV| Blinking red and green| The CATV function is disabled.
Solid Green| The CATV function is enabled and the optical signal is normal.
Blinking red| The CATV function enabled but no optical signal input.
Blinking green slowly| The CATV function is enabled and the optical signal
input is too weak.
Blinking green quickly| The CATV function is enabled and the optical signal
input is too strong.
Button explanation
| Name | Explanation |
|---|---|
| ON/OFF | Turn on/off the device. |
| RESET | Hold down for more than s seconds and release to restore the factory |
settings.
WPS| Press the button to connect the device through WPS.
WiFi| Enable/disable wireless network.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment must be installed and operated in
accordance with provided instructions and the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20
cm from all persons.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>