SDMC NE1611B WiFi Cable Modem Router User Manual
- June 3, 2024
- SDMC
Table of Contents
SDMC NE1611B WiFi Cable Modem Router
IMPORTANT: READ THESE INSTRUCTIONS BEFORE USING THE DEVICE
Installation instructions
- Position the device vertically on a stable surface, ensuring the foot stand is properly attached.
- Wall Mounting: Mounting holes are located on the back of the device. Fasten 2 screws horizontally on the wall (132 mm apart} using hollow wall anchors for stability (see Figure 1). The screw dimensions a~ illustrated in Figure 2.
- Install the unit near a power outlet so that the AC adaptor can be used without stressing the cable, and it can be easily connE!cted to a power outlet. Observe the maximum load of the electrical outlet.
- Connect the device according to the installation instructions in Figure 3.
Physical
| Items | Features |
|---|---|
| Operating Temperature | Oto40°C |
| Operating Re l ative Humidity | 10-90% (Non condensing) |
| Storage Temperature | -40 to 1o · c |
| Dimensions (H x W x D) | 218 x 155 x 55mm |
| Diagnostic LEDs (Front) | POWER, US, DS, ONLINE, 2.4G, SG, TEL1, TEL2 |
| Diagnostic LEDs (Rear) | Ethernet Link/Speed |
Interfaces
| I tems | Features |
|---|---|
| RF Interface | Externa l ‘ F ‘ type connector |
| Data I nterfaces | 4 x 10/100/1000 Base-T Ethernet (RJ-45 |
connector)
Analog Telephony Interface| 2 lines, RJ-11
Input Voltage| l00-240VAC, 50/60 Hz
Telephony
| I tems | F eatu re s |
|---|---|
| Supervisory Voltage | 48 Vdc nominal |
| Ringing Lo ad Capacity | 10 REN total; 5 per line |
Provisional High Loop
Current Mode
| Yes (40mA constant current source)
RF Downstream
| It ems | F eatures |
|---|---|
| Bonded Channels | Up to 24 |
| Tuner Configuration | Full captu r e tun in |
g range
Frequency Range| 108~1002 MHz
Data Rate (Max.)| Up to 1320 Mbps
RF Input Sensitivi ty L eve l| -15 to +15 dBmV
Modulation Type| 64QAM and 256QAM
RF Upstream
| It ems | Features |
|---|---|
| Bonded Channels | Up to 8 |
| Frequen cy Range | 5~35 MHz |
| Data Rate (Max.) | 240 Mbps |
RF Output Level
| +57 dBmV (32QAM and 64QAM, single upstream)
+54 dBmV (32QAM and 64QAM, 4-8 upstreams)
+58 dBmV (8QAM and 16QAM, single upstream)
+56 dBmV (SCDMA, single upstream)
+53 dBm (SCDMA, 2-8 upstreams)
Modulation Type| QP5K, 8-QAM, 16-QAM, 32-QAM, 64-QAM
Wireless
| I tems | Features |
|---|---|
| Fr equency Range | 2.4GHz and 5GHz |
Tran smit Power
| 2.4GHz +20dBm (MCSO), +17dbm (MCS7)
5.8GHz +19dBm (MC50), +15dbm (MCS9)
Receive l eve l s
| 2.4GHz <-80dBM 802.lln (MCSO), <-69dBm
802.lln (MCS7), HT20
5.8GHz <-78dBM 802.llac (MCSO), <-55dBm
802.llac (MCS9), VHT80
Spatial Streams (Max.)| 5
Data Rate (Max.)
| 2.4G(2×2): 300Mbps
5G(3×3): 1300Mbps
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any int erence received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for an uncontrolled environments. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>