SDMC NP2035G Dual Band WiFi GPON Terminal Installation Guide

June 12, 2024
SDMC

NP2035G
Quick Installation Guide
Dual Band WiFi GPON Terminal

Package Content

  • NP2035G x 1
  • Optic Cable x 1
  • Power Adapter x 1
  • Ethernet Cable x 1
  • Telephone Cable x 1
  • Quick Installation Guide x 1

Ports and indicators

SDMC NP2035G Dual Band WiFi GPON Terminal - fig1

Hardware connections

  1. Connect a fiber optic cable to the PON port.
  2. Connect a computer to the GE port using the Ethernet cable (optional).
  3. Connect a telephone to the TEL port using the telephone cable (optional).

SDMC NP2035G Dual Band WiFi GPON Terminal - fig2

WiFi connection

  • Using SSID
    Use the SSID and Wireless Key on the device label to connect wireless to the device. On your smartphone or notebook, find this SSID. Enter the Wireless Key to connect.

  • Using WPS
    Press the WPS button on the device and the WPS  indicator will blink. Then press the WPS button on the client. If the WPS method fails, use the SSID and wireless key to set up a WiFi connection.

Configure on the web

Configure the device on the web page according tothe information on the device label.
Open a web browser, enter the IP address, defaultUser Name and Login Password, and then click Login.

LED Indicator Explanation

Name State Description
Power On The device has been turned on.
Off The device has not been turned on.
Internet On In Routing mode and WAN connection is up.
--- --- ---
Blinking Attempt to get an IP address.
Off No internet connection or the modem router is operating in Bridge mode.
PON On The device has been registered.
Blinking Optical signal is detected.
Off No optical signal is detected.
LOS Blinking No optical signal is detected.
Off Optical signal is detected.
WIFI On Wi-Fi has been turned on.
Blinking Wi-Fi data is being transmitted.
Off Wi-Fi has been shut down.
WPS On The device is successfully connected through WPS
function.
Blinking The device is being connected through WPS function.
Off The WPS function is not enabled, or the device is successfully connected

through WPS
function.
TEL1- TEL2| On| The VOIP server has been registered.
Blinking| The voice service is in use.
Off| The VOIP server is not registered.
LAN1- LAN4| On| The LAN port is properly connected.
Blinking| Data are being transmitted.
Off| The LAN port is not connected.

Button Explanation

Name Explanation
RESET Hold down for more than 5 seconds and release to restore the factory

settings.
WPS| Press the button to connect the device through WPS.
WLAN| Enable/disable wireless network.

 Environment

Operating Temperature: 0℃~40℃
Storage Temperature: -40℃~70℃
Relative humidity: 10%~90%, non-condensing
Storage humidity: 5%~95%, non-condensing

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals