SSV WORKS RZ5-BS10 Polaris RZR XP Pro and XP4 Pro Under Rear Seat Subwoofer Enclosure Installation Guide
- September 3, 2024
- SSV WORKS
Table of Contents
SSV WORKS RZ5-BS10 Polaris RZR XP Pro and XP4 Pro Under Rear Seat Subwoofer
Enclosure Installation Guide
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by a
limited 1 year warranty against defects in material or workmanship. All SSV
Works Speakers are covered by a limited 1 year warranty against defects in
material or workmanship. Labor for replacement of defective components is not
covered.
Contact SSV Works for further warranty information.
Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.
PARTS LIST IMAGES
RZ5-BS10 Enclosure
Bracket Pack (B-MBP3009)
2-PIN Subwoofer Extension Harness (8FT) [B-H2702]
M6x16, Flanged Reduced Head Screws and Washers, 4 pack (x2) [B-HPM616HH-4]
TOOLS NEEDED FOR INSTALLATION
Attach the 4 brackets to the subwoofer enclosure using the (8) M6x16 flanged screws and washers. Do not fully tighten the screws yet.
TOOLS NEEDED FOR INSTALLATION
A. Depress the lever behind the headrest to release the backrest
B. Detach seat belts to gain access to the bottom seat tray.
C. Twist the spring clips on the firewall to remove the top and bottom firewall panels
D. Remove the screws holding the bottom seat tray using a T40 Torx driver.
E. Remove the (2) seat bolts using a 13mm socket and box wrench.
Remove the seat bottom. Repeat the process on the other seat bottom.
F. Remove the H bracket using a 15mm socket and box wrench.
G. There is a heat shield bolted to the H bracket. Some models use (2) T40 Torx screws [G] and some use (2) 10mm hex head screws [G1] to secure the heat shield. Remove these screws to release the H bracket.
H. Once the H bracket has been removed, slide the enclosure under the front
seat bracket first then the back will drop into place.
Slightly wiggle the enclosure until the brackets line up with the factory
bracket holes. Secure using the factory bolts. Do not tighten yet.
I. Keep the subwoofer enlcosure cable visible for easy access during wiring connection.
J. Secure the enclosure brackets using the M6x16mm screws. Only hand tighten each one until all the screws are aligned to the inserts.
K. Once all bracket screws are installed, tighten the screws using a 15mm and 8mm socket and/or box wrench Re install the H bracket, heat shield, bottom seat tray, seats and seat belts by reversing the installation process. Plug in the RZ5-BS10U to the B-H3704 2-pin audio, sub extension harness. Run the extension harness to the amplifier location.
WIRING DIAGRAM
| Description| Part #
---|---|---
1| 2-Pin Audio, Sub Extension Harness, 8 ft.| B-H2702
2| RZR Under seat Subwoofer Enclosure| RZ5-BS10U
Detail| Description
---|---
| Connect B-H2702 to the Subwoofer
| Connect B-H2702 to the SSV Amp Sub Output. Cut off connector and strip wires
if not using a SSV Amp.
We are committed to your satisfaction and we know you will enjoy our products.
If you have questions or need any assistance, please let us know.
SSVWORKS.COM
1-818-991-1778 EXT 2
SUPPORT@SSVWORKS.COM
Returns must be made within 30 days of purchase date. Claims for missing items or items damaged in transit must be received within five business days of receipt of merchandise. All returns must be in original packaging and in re sellable condition. Shipping fees are not refundable.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>