SSV WORKS X3-F4 4 Inch Speaker Dash Pods Instruction Manual
- August 31, 2024
- SSV WORKS
Table of Contents
PROAIM-P-SLSD-01-44-Inch-Camera-Slider-Stand-with-Junior-Pin-fig (24)
Specifications
- Product: X3-F4 4 Speaker Dash Pods
- Compatible with: 2017-2024 Can-Am Maverick x3 & x3 Max
- Manufacturer: SSV WORKS
- Warranty:
- Enclosures: Limited lifetime warranty
- Electronics: Limited 1-year warranty
- Speakers: Limited 1-year warranty
Product Usage InstructionsTools Needed for Installation
- T-30 Torx Driver
- Drill with 1/4 Drill bit
- 10mm Wrench or Rachet
- Utility Knife
Installation Steps:
- A. Remove the top dash panels on the driver and passenger side.
- B. Pry off the clips on the base under the space for the speaker.
- C. Cut off the tabs flush to the panel using a utility knife.
- D. Drill a hole at the factory with dimple marks on the outside dash panel around the speaker grille.
- E. Place the acoustic lens on top of the
- factory grille and insert screws and washers.
- F. Mount the speaker pod under the dash panel by lining up the holes and loosely mounting it.
- G. Insert screws through the acoustic lens, dash panel, and speaker pod, then tighten securely.
- H. Route the speaker wire away from moving parts and sharp metal, then connect to the amplifier.
I. Installation complete. Reassemble the dash panel.
Wiring Instructions:
Ensure correct speaker polarity when connecting to the amplifier. Refer to amplifier wiring instructions for detailed information.
FAQ
Q: What is the warranty coverage for SSV Works products?
A: SSV Works enclosures have a limited lifetime warranty, electronics have
a 1-year warranty, and speakers have a 1-year warranty against defects in
material or workmanship.
Q: Do I need any additional accessories for wiring the X3-F4?
A: If not using the pre-installed two-pin connector, you may need an
optional SSV Works plug-&-play harness (WP-H1149 – sold separately) for
wiring.
Q: How should I ensure proper sound quality when connecting the
speakers?
A: Connect the speaker wires with correct polarity (+ to + and -to -) and
refer to amplifier wiring instructions for more detailed information,
especially when using an SSV Works complete system.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by a
limited 1-year warranty against defects in material or workmanship. All SSV
Works Speakers are covered by a limited 1-year warranty against defects in
material or workmanship. Labor for the replacement of defective components is
not covered. Contact SSV Works for further warranty information.
Please read and understand these instructions completely before installation to avoid possible injury or damage to the accessory or vehicle.
TOOLS NEEDED FOR INSTALLATION
- T-30 Torx Driver
- Drill 1/4” Drill bit
- 10mm Wrench or Rachet
- Utility Knife
PARTS LIST
- X3-F4 Enclosures (1 pair)
- Acoustic Lens (1 pair)
- M6 x 1.0 Screws x 4
- M6 Washers x 4
- 10mm Nut x 2
- M6 x 25mm Screws x 2
PARTS LIST IMAGES
Installation Steps
- A. Remove the top dash panels on the driver (7 screws with 2 clips) and passenger side (5 screws with 2 clips).
- B. Pry off the 4 clips on the base under the empty space for the speaker.
- C. Using a utility knife, cut off the 4 tabs flush to the panel
- D. Drill a hole using a 1/4” drill bit at the factory dimple marks (as shown above) on the outside dash panel around the speaker grille.
- E. Place the acoustic lens on top of the factory grille, line up the holes, and insert the 2 top M6x1.0 (shorter) screws and washers.
- F. Place the speaker pod under the dash panel and line up the holes on the speaker pod with the 2 top screws and loosely mount the pod to the dash panel.
- G. Insert the M6x25mm screw by pushing it through the acoustic lens, dash panel, and speaker pod. Tightly screw down using the washer and 10mm nut. Now tighten the previous 2 M6x1.0 screws.
- H. Route the speaker wire away from any moving parts and any sharp metal, then connect to the amplifier. Connecting the X3-D4 using the pre-installed, two-pin connector will require an optional SSV Works plug-&-play harness (WPH1149 – sold separately). If you are not using the WP-H1149 harness, simply cut off the two-pin connector and follow the wiring instructions below.
Installation complete. Reassemble the dash panel.
For proper sound, ensure the speaker polarity is correct and connect the “+”
to the “+” and the “-“to the “-“from the speaker wire to the amplifier. If
using with an SSV Works complete system refer to the amplifier wiring
instructions for more detailed wiring information. © 2024 SSV Works,
Camarillo, CA 93012 X3-F4 Rev. A 8-1-24SSV WORKS, 2610Calle Quetzal,
Camarillo, CA 93012
www.SSVworks.com | Phone:
818-991-1778 | Fax:
866-293-6751
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>