immax 07527L NEO Smart PIR Sensor 2in1 Zigbee 3.0 User Manual
- August 31, 2024
- immax
Table of Contents
immax 07527L NEO Smart PIR Sensor 2in1 Zigbee 3.0
Product Information
Specifications:
- Product Name: IMMAX NEO SMART PIR SENSOR 2IN1 ZIGBEE 3.0
- Power Source: CR123A 3V battery or USB C port
- Installation Methods: 3M tape and hinge bracket or fixed attachment with screws
- Supported Platforms: Immax NEO PRO app on App Store or Google Play
- Installation Height: 1.8 – 2.1 meters
Product Usage Instructions
Getting Started:
- Download the Immax NEO PRO app from the App Store or Google Play.
- Open the battery cover and insert the CR123A 3V battery, ensuring to remove the protective strip.
- Press and hold the RESET BUTTON for more than 5 seconds to enter pairing mode (LED will start blinking).
Installation:
- Choose the preferred installation method: 3M tape and hinge bracket or fixed attachment with screws.
- Place the device in pairing mode by following the instructions provided.
- In the Immax NEO PRO app, search for Multi sensor (zigbee) or Other zigbee devices and select a smart gateway for pairing.
Battery Replacement:
If you receive a low battery warning, replace the CR123A 3V battery
promptly. Ensure correct polarity when inserting the new battery.
Maintenance:
Keep the device clean by wiping it with a soft cloth. Avoid using harsh
chemicals or solvents for cleaning.
Frequently Asked Questions (FAQ):
-
Q: How do I know if the device is in pairing mode?
A: The LED will start blinking when the device is in pairing mode. If it does not flash, the device is either paired or the battery is low. -
Q: Can the PIR sensor be powered using the USB C port?
A: Yes, the PIR sensor can also be powered using the USB C port, with the battery serving as a backup power source during outages. -
Q: What should be the installation height of the sensor?
A: The recommended installation height for the sensor is between 1.8 – 2.1 meters.
PACKAGE CONTENTS
- PIR sensor
- Holder
- User manual
PRODUCT INTRODUCTION
POWER PORT
SAFETY INFORMATION
CAUTION: Keep out of reach of children. This product contains small
parts, which may cause suffocation or injury if swallowed.
WARNING: Every battery has the potential to leak harmful chemicals that
can damage skin, clothing or area where the battery is stored. To avoid the
risk of injury, do not allow any substance from the battery to come into
contact with the eyes or skin. Every battery may burst or even explode if
exposed to fire or other forms of excessive heat. Take care when handling the
batteries. To reduce the risk of injury from mishandling the batteries, take
the following precautions:
- Do not use different brands and types of batteries in the same device
- When replacing the batteries, always replace all the batteries in the device
- Do not use rechargeable or reusable batteries.
- Do not allow children to insert batteries without supervision.
- Follow the battery manufacturer’s instructions for proper battery handling and disposal.
CAUTION: The product and batteries should be disposed of at a recycling
centre.
Do not dispose of them with normal household waste.
CAUTION: To ensure safe use of the product, wires must be brought at the
installation site according to valid regulations. The installation must only
be carried out by an individual with the appropriate certification in the
field of electronics.
During installation or when a fault is detected, the power cable must always
be disconnected from the socket (in the case of direct connection, the
relevant circuit breaker must be switched off). Improper installation can
damage the product and cause injury.
CAUTION: Do not disassemble the product, electric shock may occur.
CAUTION: Use only the original power adapter provided with the product.
Do not operate the device if the power cord shows signs of damage.
CAUTION: Follow the instructions in the enclosed manual.
GETTING THE DEVICE UP AND RUNNING
DOWNLOAD THE IMMAX NEO PRO APP AND REGISTER
Scan the QR code to download the immax NEO PRO app. Or search for and install
the Immax NEO PRO app in the App Store or Google Play.
INSTALLATION
INSTALLATION OF THE DEVICE
- Open the battery cover and remove the protective strip from the battery
- Put the device into pairing mode. The LED will flash
- Open the Immax NEO PRO application and search for Multi sensor (zigbee) and/ or Other zigbee devices. Select a smart gateway and proceed according to the instructions in the application.
Notes: The PIR sensor can also be powered using the USB C port. In this case, the battery will serve as a backup power source during a power outage.
INSTALLING THE DEVICE
This device supports 2 installation methods. By attaching it with 3M tape
and hinge bracket, or by fixed attachment with screws.
Notes: The installation height of the sensor should be 1.8 – 2.1 meters.
REPLACING THE BATTERY
The sensor is equipped with a CR123A 3V battery. If you receive a low battery
warning in the app, replace the battery as soon as possible. When inserting a
new battery, make sure to observe the polarity.
MAINTENANCE
Protect the device from contamination and soiling. Wipe the device with a soft
cloth, do not use rough or coarse materials.
DO NOT USE solvents or other aggressive cleaners or chemicals.
RESET BUTTON
- Long press (more than 5 seconds) to enter pairing mode. The LED will start blinking LED will flash
- If the LED flashes, the device is in pairing mode. If it does not flash, the device is paired or the battery is low.
TECHNICAL SPECIFICATION
- Zigbee communication protocol: 3.0
- Frequency: 2400MHz – 2483.5MHz
- Maximum RF output power: 6±1dBm
- Wireless range: 30m direct line of sight, 10m in built-up area
- PIR (Passive Infrared Sensor) detection technology
- Detection angle: 120°
- Light detection range: 0 – 1000 lux
- Power source: 1x CR123A 3V or USB C 5V 1A battery (adapter and USB C cable not included)
- Battery life: up to 254 days in standby mode
- Standby power consumption: 148 uAh (per hour)
- Power consumption during operation: 3 uAh (for one operation)
- Attachment with screws or 3M adhesive tape
- Mounting height: 1.8 – 2.1m
- Operating temperature: -10°C to +50°C
- Operating humidity: 95% maximum
- Degree of protection: IP20
- Certifications: CE
- Sensor dimensions: 48x21x29mm
- Sensor weight: 51.2g
- Bracket dimensions: 50x50x32mm
- Holder weight: 31,4g
A Declaration of Conformity has been issued for this product. More information
can be found at www.immax.eu
If you have any questions or need advice, please contact us at
support@immax.eu
Manufacturer and importer:
IMMAX, Pohoří 703, 742 85 Vřesina, EU |
www.immaxneo.cz |
www.immaxneo.com
Designed in the Czech Republic, made in China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>