SSV WORKS 230-FRT3-SWE12 Alpha12 Switcher Box Installation Guide
- August 31, 2024
- SSV WORKS
Table of Contents
SSV WORKS 230-FRT3-SWE12 Alpha12 Switcher Box
Product Information
Specifications:
- Product Name: Alpha12 Switcher Box
- Model Number: 230-FRT3-SWE12
- Compatibility: 2021-Up Ford F150 Raptor (Gen 3)
- Manufacturer: SSV Works
- Warranty: Limited 1-year warranty against defects in material or workmanship
Product Usage Instructions
Installation:
Before beginning the installation process, ensure you have the necessary
tools:
- Phillips Screw Driver
- Pry Tool
- Drill
- 5/8 Drill Bit
- T10 Torx Driver
Panels and Dash Disassembly:
- Remove the overhead console using a plastic pry tool to release the clips securing it to the headliner.
- Pull down the console and disconnect the connectors.
- Drill a 5/8 hole towards the front of the sunglass holder cavity.
- Mount the ALPHA12 controller to the F150 Raptor fascia using thread cutting screws.
- Route the controller cable through the drilled hole and run it towards the passenger side A pillar.
- Secure the fascia to the sunglass holder cavity using Phillips screws and flat washers.
- Reconnect the connectors and reinstall the overhead console.
Switch Works Brain Module Installation:
- Mount the brain module in the engine bay above the fusebox.
- Attach the module to the bracket using supplied screws.
- Mount the fender bracket to the fender wall above the fusebox using factory bolts.
- Connect accessories to the harnesses and plug them into the brain module.
- Ensure the 15 button controller is plugged in before connecting power and ground cables to the battery.
Frequently Asked Questions (FAQ):
-
Q: What is the warranty coverage for SSV Works products?
A: All SSV Works Non-Electronic Parts are covered by a limited lifetime warranty, while SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. For further warranty information, contact SSV Works. -
Q: What tools are needed for installing the Alpha12 Switcher Box?
A: The tools needed for installation include a Phillips Screw Driver, Pry Tool, Drill, 5/8 Drill Bit, and T10 Torx Driver.
Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.
PARTS CONTENTS
INSTALLATION
TOOLS NEEDED FOR INSTALLATION
- Phillips Screw Driver
- Pry Tool
- Drill
- 5/8” Drill Bit
- T10 Torx Driver
PANELS AND DASH DISASSEMBLY
- A. Remove the overhead console by using a plastic pry tool carefully working all around the console.
- B. Note that there are 4 clips that secure the overhead console to the headliner.
- C. Pull down the overhead console and unplug the connectors.
- D. Remove the sunglass holder. Drill a 5/8” hole on towards the front of the sunglass holder cavity (front is the windshield side).
- E. Mount the ALPHA12 controller to the F150 Raptor fascia using the 4-40x.75” thread cutting screws (x4).
- F. Note that the F150 Raptor Overhead Fascia mounts behind the overhead console and is secured to the 2 posts circled above.
- G. Route the controller cable through the hole drilled on the overhead console and run it towards the passenger side A pillar.
- H. Secure the F150 Raptor Fascia to the sunglass holder cavity using the #7-19x.75 Phillips screws and M4 flat washers (x2 each).
- I. Plug the connectors and re-install the overhead console.
SWITCH Works Brain Module Installation
TOOLS NEEDED FOR INSTALLATION
- Phillips Screw Driver
- 8, 10, 12 & 13mm Wrench
A. The SWITCH Works brain module is mounted in this area of the engine bay above the fusebox.
B. Mount the SWITCH Works brain module to the B-MB3192 bracket using the supplied M5x10mm screw (x4).
C. Mount the fender bracket (B-MB3191) to the fender wall (above the fusebox) using the factory bolts.
D. Attach the module bracket to the fender bracket using the supplied M6-1x12mm hex head bolts (B-S2870).
E. Connect the accessories to be used to the High and Low current harnesses and plug the harnesses to the brain module. NOTE that the 15 button controller MUST be plugged in to the module before connecting the power and ground cables to the battery. Snap on the terminal cover to the module’s + terminal.
F. Refer to the SW-E12 instructions manual for a detailed installation and programming procedure of the SWITCH Works ALPHA12 system.
SWITCH Works is a product by SSV Works. We are committed to your satisfaction and we know you will enjoy our products. If you have questions or need any assistance, please let us know.
WARRANTY INFORMATION
ALL SWITCH Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Contact SSV Works for further warranty information.
All SSV Works Non-Electronic Parts are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.
SSVWORKS.COM
11-818-991-1778 EXT 2
SUPPORT@SSVWORKS.COM
Returns must be made within 30 days of purchase date. Claims for missing items or items damaged in transit must be received within five business days of receipt of merchandise. All returns must be in original packaging and in re- sellable condition. Shipping fees are not refundable.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>