SSV Works 240-TTU3H-SWE12 Alpha12 Switcher Box Installation Guide

August 31, 2024
SSV WORKS

240-TTU3H-SWE12 Alpha12 Switcher Box

Specifications:

  • Model: 240-TTU3H-SWE12
  • Compatibility: 2022-Up Toyota Tundra (Gen 3)
  • Product: Hybrid Alpha12 Switcher Box
  • Warranty: Limited 1-year warranty against defects in material
    or workmanship

Product Usage Instructions:

Parts Contents:

  • Toyota Tundra Overhead Fascia [B-D3306]
  • Toyota Tundra Overhead Mounting Bracket [B-D3307]
  • Toyota Tundra ALPHA12 Brain Mount Bracket [B-MB3365]
  • 7-19×3/4 Phillips Screw (x7) [B-S1656]

  • M5x10 Pan Head Screw (x4) [BS1158]
  • 4-40x.375 Thread Cutting Screw (x4) [B-S3262]
  • M6x12mm Hex Head Bolt (B-S2780)
  • 4-Pin Extension Cable, 6 ft.
  • Zip tie and zip tie panel tree snap
  • 4 Gauge Power Cable Kit, 16 ft.

Installation:

Tools Needed for Installation:

  • Phillips Screw Driver
  • 3mm and 16mm Drill Bit
  • Drill
  • Pry Tool
  • Pick Tool

Overhead Console Disassembly:

  1. A. Use both hands and grab the back edge of
    the overhead console. Pull down firmly until the back side snaps
    loose. Slide the console forward towards the windshield.

  2. B. Disconnect the harness from the
    console.

  3. C. Remove the sunglass holder using a pry tool
    to unsnap the left side.

  4. D. Mark drill points on the overhead console
    using a pick tool inserted into the screw posts.

  5. E. Drill 3 holes using a 3mm drill bit as
    marked.

  6. F. Drill a 16mm hole for the controller cable
    connector.

  7. G. Assemble the Tundra fascia to the mounting
    bracket using the provided screws.

  8. H. Mount the ALPHA12 controller to the Tundra
    fascia using thread cutting screws.

  9. I. Insert the cable through the drilled hole
    and place the controller in the sunglass holder cavity.

  10. J. Secure the bracket to the overhead console
    using screws.

  11. K. Run the ALPHA12 controller cable along the
    headliner towards the driver side A pillar and down to the
    firewall.

FAQ:

Q: What is the warranty coverage for SSV Works products?

A: All SSV Works Non-Electronic Parts are covered by a limited
lifetime warranty against defects in material or workmanship. All
SSV Works Electronics are covered by a limited 1-year warranty
against defects in material or workmanship. Labor for replacement
of defective components is not covered. Contact SSV Works for
further warranty information.

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

240-TTU3H-SWE12
2022-Up Toyota Tundra (Gen 3) Hybrid
Alpha12 Switcher Box
Mounting Kit

WARRANTY INFORMATION: ALL SWITCH Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Contact SSV Works for further warranty information.

Please read and understand these

!

instructions completely before installation to avoid possible injury, or

damage to the accessory or vehicle.

BY

PARTS CONTENTS

Toyota Tundra Overhead Fascia [B-D3306]

Toyota Tundra Overhead Mounting Bracket [B-D3307]

Toyota Tundra ALPHA12 Brain Mount Bracket [B-MB3365]

7-19×3/4″ Phillips Screw (x7) [B-S1656]

M5x10 Pan Head Screw (x4) [BS1158]

4-40x.375 Thread Cutting Screw (x4) [B-S3262]

M6x12mm Hex Head Bolt (B-S2780)

4-Pin Extension Cable, 6 ft.

Zip tie and zip tie panel tree snap.

4 Gauge Power Cable Kit, 16 ft.
2

INSTALLATION

WARRANTY INFORMATION: All SSV Works Non-Electronic Parts are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

Please read and understand these

!

instructions completely before installation to avoid possible injury, or

damage to the accessory or vehicle.

TOOLS NEEDED FOR INSTALLATION
– Phillips Screw Driver – 3mm and 16mm Drill Bit – Drill

– Pry Tool

– Pick Tool

OVERHEAD CONSOLE DISASSEMBLY

A
A. Use both hands and grab the back edge (edge closest to the windshield) of the overhead console. Pull down firmly until the back side snaps loose. Slide the console forward towards the windshield.

B
B. Note that the console is hooked onto the headliner with these 2 tabs. Disconnect the harness.

C
C. Remove the sunglass holder. Open the sunglass holder and use a pry tool to unsnap the left side (refer to picture above).

D
D. Insert a pick tool into the 3 screw posts circled above to mark drill points to the overhead console.

3

E

E

E. Mark the drill guides and drill 3 holes using a 3mm drill bit.

F
F. Drill a 16mm hole for the controller cable connector. Set aside the console for now.

G
G. Assemble the Tundra fascia to the mounting bracket using the supplied (4)

7-19×3/4″ Phillips screws (B-S1656).

GI1
G1. Picture above shows the screw holes used to assemble the Tundra fascia to the mounting bracket.

HJ
H. Mount the ALPHA12 controller to the Tundra fascia using (4) 4-40x.375 thread cutting screws (B-S3262).

4

I
I. Picture above shows the orientation of the ALPHA12 controller to the fascia. Completed installation of the Gen 3 Toyota Tundra SWE12 15-Button Controller.

J
J. Insert the cable through the hole drilled on the overhead console and place the controller and bracket in the sunglass holder cavity.

K
K. Flip the overhead console upside down and use (3) #7-19×3/4″ Phillips screws (B-S1656) to secure the bracket.

L
L. Run the ALPHA12 controller cable along the headliner towards the driver side A pillar and down to the firewall. Use the supplied 6 foot controller extension cable and fish through the firewall grommet to the ALPHA12 brain mount location.

M. Reinstall the A pillar trim and overhead console.

M
Completed installation of the Gen 3 Toyota Tundra SWE12 15-Button Controller.
5

SWITCH Works Brain Module Installation

TOOLS NEEDED FOR INSTALLATION

– 10mm, 12mm & 13mm Socket Wrench

– Phillips Screw Driver

A
A. The SWITCH Works brain module is mounted on the driver side fender above the fusebox.

B
B. Mount the ALPHA12 brain module to the brain bracket (B-MB3366) using (4) M5x10mm pan head screws (B-S1158).

C

D

C. Remove the front bolt of the ABS pump bracket using a 12mm wrench.

D. Remove the horn bracket bolt using a 10mm wrench.

6

E. Remove the hood release cable from the cable clamp.

E

F

F. Position the horn and the ALPHA12 brackets and fasten using the horn bracket bolt. Do not tighten the bolt yet.

G
G. Put the upper ALPHA12 bracket tab behind the factory hood lift support shock mount and fasten using the supplied M6x12mm screw (B-S2780). Do not tighten the screw yet.

H
H. Position the bottom left tab of the ALPHA12 bracket to the ABS pump bracket and fasten using the factory bolt. Tighten all 3 mounting bolts to secure the ALPHA12 brain module.

I
I. Connect the accessories to be used to the High and Low current harnesses and plug the harnesses to the brain module.

J
J. Connect the ground wire from the ALPHA12 brain module to the factory grounding point on the driver side fender.

7

K

K1

K. NOTE that the 15 button controller MUST be plugged in to the module before connecting the power cable to the battery. Run the power wire from the ALPHA12 brain module along the firewall towards the battery located under the driver side backseat [K1].

L
L. Fish the 4 gauge power wire through the firewall grommet towards inside the cabin .

M
M. Run the power cable along the doorsill towards the backseat.

N. Insert the cable under the backseat bottom panel.

N

O

O. Cut the power cable and install the provided fuseholder no more than 18″ away from the ring terminal. NOTE that the 15 button controller MUST be plugged in to the module before connecting the power cable to the battery.

8

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
WARRANTY INFORMATION: All SWITCH Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Contact SSV Works for further warranty information.

SW-E12
12 OUTPUT
ELECTRONIC ACCESSORIES
SMART SWITCHER

Please read and understand these

!

instructions completely before installation to avoid possible injury, or

damage to the accessory or vehicle.

BY

P

1

P. Refer to the SW-E12 instructions manual for a detailed installation and programming procedure of the SWITCH Works Alpha12 system.

THIS CONCLUDES THE INSTALLATION PROCESS. QUESTIONS? PLEASE CONTACT SSV WORKS AT 818-991-1778 OR EMAIL SUPPORT@SSVWORKS.COM

12

© 2024 SSV Works, Oxnard, CA 93030 TTU3H-SWE12 Rev.A 6-21-24

9

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SSV WORKS User Manuals

Related Manuals