SSV WORKS X3-F65 6.5 Inch Front Kick Speaker Pods Instruction Manual

: August 30, 2024
: SSV WORKS

Table of Contents

X3-F65 6.5 Inch Front Kick Speaker Pods
Specifications
Product Usage Instructions
Tools Needed for Installation
Parts List
Installation Steps
- Frequently Asked Questions (FAQ)
Q: What warranty coverage does the product come with?
Q: What tools are needed for installation?

X3-F65 6.5 Inch Front Kick Speaker Pods

“`html

Specifications

Product Name: X32-PHZ+FK
Compatibility: SSV Can Am Maverick X3 Audio Kits
Manufacturer: SSV WORKS
Warranty: Limited lifetime warranty for enclosures, 1 year
warranty for electronics and speakers

Product Usage Instructions

Tools Needed for Installation

T-30 Torx Driver
Drill with 1/4 Drill bit
Scribe or Punch tool
Phillips / flat head screwdriver
10 mm wrench

Parts List

X3-F65 Enclosures (1 pair)
M6 x 1.0 Screws x 6
M6 Washers x 6
M5 screws and washers x 8
Large Bracket x 2
Small Bracket x 2
Driver Side Template
Passenger Side Template

Installation Steps

Step A: Remove the eleven (11) T30 Torx bolts
that secure the fender. Remove the metal clip securing the top
panel to the fender.
Step B: Cut out the template
(Driver/Passenger) along the cut line. Position the template on the
inner plastic, aligning it with the factory panel.
Step C: Mark the center of the three (3) drill
points on the template using a scribing tool.
Step D: Drill holes for mounting the pod and
route the speaker cable connector.
Step E: Place the larger bracket inside the
cage tube.
Step F: Place the smaller bracket on top of
the bar and align the holes with the large bracket. Tighten both
brackets using M5 screws.
Step G: Route the speaker connector through
the drilled hole.
Step H: Position the kick pod for mounting and
hand tighten using provided M6 screws and washers.
Step I: Once all screws are inserted, tighten
them securely.
Step J: Make your speaker connection.
Step K: Installation is complete. Repeat for
the driver side pod.

Frequently Asked Questions (FAQ)

Q: What warranty coverage does the product come with?

A: All SSV Works enclosures are covered by a limited lifetime
warranty against defects in material or workmanship. Electronics
and speakers are covered by a limited 1 year warranty.

Q: What tools are needed for installation?

A: The tools required for installation include a T-30 Torx
Driver, Drill with a 1/4 Drill bit, Scribe or Punch tool,
Phillips/flat head screwdriver, and a 10 mm wrench.

“`

SSV WORKS, 2610 Calle Quetzal, Camarillo, CA 93012 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

X32-PHZ+FK
2017-2024 Plug-&-Play Front Kick Speaker Pods Add-On Kit for
SSV Can Am Maverick X3 Audio Kits

Maverick X3
pg 3
Front Speaker Kick Pod Add-On Kit Installation
pg 5
Front Kick Panel Speaker Wiring Diagram

1

FRONT KICK PODS ADD-ON KIT PARTS LIST

WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

Please read and understand these

!

instructions completely before installation to avoid possible injury, or

damage to the accessory or vehicle.

TOOLS NEEDED FOR INSTALLATION

– T-30 Torx Driver – Drill with 1/4″ Drill bit – Scribe or Punch tool

– Phillips / flat head screwdriver
– 10 mm wrench

PARTS LIST
1. X3-F65 Enclosures (1 pair) 2. M6 x 1.0 Screws x 6 3. M6 Washers x 6 4. M5 screws and washers 8

5. Large Bracket x 2 6. Small Bracket x 2 7. Driver Side Template 8. Passenger Side Template

PARTS LIST IMAGES

X3-F65 Enclosures (1 pair)
Large Bracket x 2

M6 x 1.0 Screws x 6 Small Bracket x 2

M6 Washers x 6

M5 Screws and Washers x 8

SPEAKER WIRE

DRIVER SIDE
X3-F65 KICKPOD DRILL TEMPLATE – DRIVER SIDE
Driver Side Template

PASSENGER SIDE
X3-F65 KICKPOD DRILL TEMPLATE – PASSENGER SIDE
Passenger Side Template

Speaker “Y” Harness (B-H1463)
2

RGB “Y” Splitter(B-H3072)

Front Speaker Harness (B-H1909)

RGB Speaker Harness (B-H2935)

FRONT KICK PODS ADD-ON KIT INSTALLATION

A
A. Remove the eleven (11) T30 Torx bolts that secure the fender. Note: There is three (3) T30 screws on passenger side and two (2) on driver side that will have a 10mm bolt. Remove the metal clip that is securing the top panel to the fender.

B
B. Cut out the template (Driver/Passenger) along the cut line. Position the template on inner plastic ,making sure to square up the template along the factory panel as shown in image E.

Pod holes

Cable hole

C
C. Using a scribing tool, mark the center of the three (3) drill points illustrated on the template as shown in image F.

D
D. Using a 1/4″ drill bit, drill holes for mounting the pod. Use a 1/2″ drill bit to drill the hole for routing the speaker cable connector.

E
E. Place the larger bracket on inside of the cage tube.

F
F. Place the smaller bracket on top of the bar and line up the holes with the large bracket. Using the M5 screws, tighten both brackets to one another (make sure the drilled out holes line up to brackets)
3

G
G. Route speaker connector through the 1/2″ hole that was drilled out.

H
K. Place the kick pod in position for mounting. Use the provided M6 screws and washers to hand tighten the pod to the kick panel.

I

J

L. Once all screws have been inserted into pod , tighten all three (3) screws.

M. Make your speaker connection

Installation is complete. Repeat for driver side pod. 4

FRONT KICK PODS ADD-ON KIT WIRING DIAGRAM

B

F

A 1

2 DE

C

3

4

H G

G H

Description
1 Speaker “Y” Harness 2 RGB “Y” Splitter 3 Front Speaker Harness (48″) 4 RGB Speaker Harness (48″)

Part # B-H1463 B-H3072 B-H1909 B-H2935

Detail
A B C D E F G H

Description Connect Front Output from B-H2605 to B-H1463 Connect LIT-CC Output to B-H3072 Connect to Dash Speaker Panel Harness Connect to B-H1909 for Front Kick Pods Connect to B-H2935 for Front Kick Pods RGB Speakers Connect to Dash Speaker Panel RGB Harness Connect to Front Kick Pods Connector Connect to Front Kick Pods RGB Connector

5

DRIVER SIDE

X3-F65 KICKPOD DRILL TEMPLATE – DRIVER SIDE

6

7

SPEAKER WIRE
PASSENGER SIDE X3-F65 KICKPOD DRILL TEMPLATE – PASSENGER SIDE

8

9

© 2024 SSV Works,Camarillo, CA 93012 X32-PHZ+FK 8-1-24
10