EFFYDESK Home Desk Instruction Manual
- June 3, 2024
- EFFYDESK
Table of Contents
EFFYDESK Home Desk
Technical Data
- Segment Column 2
- Recommend Load <220 lbs
- Height Range 710-1160mm
- Maximum Load 240 lbsS
- Input Voltage 110-240v
- Speed 30mm/s
- Certification UL
Accessory List
Tool Required
Parts List
Thank you for your order!
If you have any issues with your product, please feel free to contact us via
team@effydesk.ca or
info@effydesk.ca We will help you resolve the issue
as soon as possible.
For more information, please visit
https://effydesk.ca/pages/how-to-assemble-your-height-adjustable-standing-
desk
INSTALLATION INSTRUCTION
- Separate the Crossbar ⑧ and you will find the Crossbar Rail inside.
- Insert one of the Crossbar Ends into the one of the Lifting Columns ③ and secure with screws. Repeat the same step for the other Lifting Column.
- Attach the Side Bracket ⑥ to one of the Lifting Columns. Repeat the same step for the other Lifting Column.
- Slide the two Crossbar Ends back into the Crossbar Rail. Please make sure to fit the slots as shown below.
- Attach both Feet ④ to the bottom of the Lifting Columns.
- Install the tabletop (Predrilled / Non-predrilled ).
- Connect all the cables to the Control Box ①.
- Firmly secure the Crossbar with Screws (A) and attach the Keypad ⑦ with Screws (F) to the tabletop.
- Plug the cable from the Keypad into the Control Box and flip the table onto its feet.
Note: The Control Box is equipped with a gyro sensor so the table and the Control Box must be level in order to work properly or else it will not move up and down.
Prepare for First-time Use
Before plugging in the table, make sure that:
- The Lifting Columns are level and set at their lowest position.
- All the screws are tightened to avoid the desk from becoming wobbly.
Calibrate the desk by following the steps below:
- Please press the Down button and hold for 10-15 seconds until the table stutters and beeps.
- Release the button. Your desk is ready to use!
Operation
Program Presets
-
Adjust the table to the desired height, then press M.
“S-“ will flash on the display. -
Press a number to set the desired height as a preset.
Set Stand Up Reminder
- Press and hold the number 1 and 3 buttons at the same time.
- When display shows “0.0h”, press the Up or Down arrows to adjust the reminder time by 30 minute (0.5 hr) increments.
- Once the display stops flashing, your reminder has been set.
- Repeat above steps to set another reminder for next time.
Advanced Safety Feature: Lock and unlock the table
- Press the Up and Down buttons at the same time for 5 seconds, until “LOC” appears on the display.
- All buttons will be deactivated and no changes can be made.
- Press the Up and Down buttons together again to unlock the Keypad and all of the table’s features.
Set Maximum Height Limit
- Raise the desk to the desired maximum height.
- Press M and the Up button together for 5 seconds until you hear a beep. This sets the maximum height limit.
Set Minimum Height Limit
- Lower the desk to the desired minimum height.
- Press M and the Down button together for 5 seconds unti you hear a beep. This sets the minimum height limit.
Changing from Centimetres to Inches
- Press M for 10 seconds, the Keypad will display “1-1”.
- Press the Down button and it will change to “1-0”.
- Press M for 10 seconds to lock the setting.
Reset the table
When an error code or “RST” appears on the display, please reset the table.
- Unplug the power cord from the Control Box.
- Unplug the cable that connects the Keypad to the Control Box.
- Wait 30 minutes and plug all the cables back in again.
- Press the Down button and hold for 10-15 seconds until the table stutters and beeps.
If“HOT” appears on the display
- Please unplug and replug and let it cool off for a couple of minutes before proceeding.
If you have any questions, please contact us at
team@effydesk.ca or info@effydesk.ca www.effydesk.ca
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>