EFFYDESK L Shaped Desk Instruction Manual

June 3, 2024
EFFYDESK

EFFYDESK-logo

EFFYDESK L Shaped Desk Instruction

Instruction

EFFYDESK-L-Shaped-Desk-Instruction-fig-1

Technical Data

EFFYDESK-L-Shaped-Desk-Instruction-fig-23

Accessory List

Tool Required

Parts List

EFFYDESK-L-Shaped-Desk-Instruction-fig-4

Thank you for your order!
If you have any issues with your product, please feel free to contact us via team@effydesk.ca or info@effydesk.caWe will help you resolve the issue as soon as possible.
For more information, please visit https://effydesk.ca/pages/how-to-assemble- your-height-adjustable-standing-desk

  • STEP 1
    Separate the Crossbar ⑦ and you will find the Crossbar Rail inside.EFFYDESK-L-Shaped-Desk-Instruction-fig-5

  • STEP 2
    Insert one of the Crossbar Ends into the one of the Lifting Columns ③ and secure with screws. Repeat the same step for the other Lifting Column.EFFYDESK-L-Shaped-Desk-Instruction-fig-5

  • STEP 3
    Attach the Side Bracket ⑥ to one of the Lifting Columns. Repeat the same step for the other Lifting Column.EFFYDESK-L-Shaped-Desk-Instruction-
fig-6

  • STEP 4
    Attach the Crossbar as shown.EFFYDESK-L-Shaped-Desk-Instruction-
fig-8

  • STEP 5
    Slide the Crossbar two Rails back into the Crossbar Ends. Please make sure to fit the slots as shown below.EFFYDESK-L-Shaped-Desk-Instruction-
fig-9

  • STEP 6
    Attach the Feet ④ to the bottom of the Lifting Columns.EFFYDESK-L-Shaped-
Desk-Instruction-fig-10

  • STEP 7
    Use the screws to tighten the Hangers onto the Crossbar.EFFYDESK-L-Shaped-
Desk-Instruction-fig-11 Note: The screws do not go through the Crossbar.Hangers, Allen Key and screws are found in a separate bag.

  • STEP 8
    Please note these parts are found in the table top package

  • STEP 9
    Install the tabletop (Predrilled / Non-predrilled).EFFYDESK-L-Shaped-Desk-
Instruction-fig-13

  • STEP 10
    Firmly secure the Crossbar with Screws (A) andconnect all the cables to the Control Box ①.EFFYDESK-L-Shaped-Desk-Instruction-
fig-14

  • STEP 11
    Attach the Cable Tray ⑧ to the Hangers with screws.EFFYDESK-L-Shaped-
Desk-Instruction-fig-15

  • STEP 12
    Attach the Keypad ⑨ with Screws (F) to the tabletop.EFFYDESK-L-Shaped-
Desk-Instruction-fig-16

  • STEP 13
    Plug the cable from the Keypad into the Control Box and flip the table onto its feet.EFFYDESK-L-Shaped-Desk-Instruction-fig-17 Note: The Control Box is equipped with a gyro sensor so the table and the Control Box must be level in order to work properly or else it will not move up and down.

Prepare for First-time Use

EFFYDESK-L-Shaped-Desk-Instruction-fig-17

Before plugging in the table, make sure that:

  • The Lifting Columns are level and set at their lowest position.
  • All the screws are tigh tened to avoid the desk from becoming wobbly.
  • There is no object above or beneath the desk within its range of movement as it may result in physical danage.

Calibrate the desk by following the steps below:

  • Please press the Down button and hold for 10-15 seconds until the table stutters and beeps.
  • Release the button. Your desk is ready to use!

Operation Guide Program Presets

  • Adjust the table to the desired height, then press M. “S-“will flash on the display.
  • Press a number to set the desired height as a preset.

Set Stand Up Reminder

  • Press and hold the number 1 and 3 buttons at the same time.
  • When display shows “0.0h”, press the Up or Down arrows to adjust the reminder time by 30 minute (0.5 hr) increments.
  • Once the display stops flashing, your reminder has been set.
  • Repeat above steps to set another reminder for next time.

Advanced Safety Feature: Lock and unlock the table

  • Press the Up and Down buttons at the same time for 5 seconds, until “LOC” appears on the display.
  • All buttons will be deactivated and no changes can be made.
  • Press the Up and Down buttons together again to Gonvfish

Set Maximum Height Limit

  • Raise the desk to the desired maximum height.
  • Press M and the Up button together for 5 seconds until you hear a beep.
  • This sets the maximum height limit.

Set Minimum Height Limit

  • Lower the desk to the desired minimum height.
  • Press M and the Down button together for 5 seconds unti you hear a beep. This sets the minimum height limit.

Changing from Centimetres to Inches

  • Press M for 10 seconds, the Keypad will display “1-1”.
  • Press the Down button and it will change to “1-0”.
  • Press M for 10 seconds to lock the setting.

Reset the table

W hen an error code or “RST” appears on the display, please reset the table.

  • Unplug the power cord from the Control Box.
  • Unplug the cable that connects the Keypad to the Control Box.
  • Wait 30 minutes and plug all the cables back in again.
  • Press the Down button and hold for 10-15 seconds until the table stutters and beeps.

If“HOT” appears on the display

  • Please unplug and replug and let it cool off for a couple of minutes before proceeding.

If y ou have any questions, please contact us at team@effydesk.ca or info@effydesk.ca www.effydesk.ca

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals