EFFYDESK ED-BIZ Business Office Standing Desk Instruction Manual
- June 3, 2024
- EFFYDESK
Table of Contents
EFFYDESK ED-BIZ Business Office Standing Desk
Technical Data
Accessory List
Tools Required
Parts List
Thank you for your order!
If you have any issues with your product, please feel free to contact us via
team@effydesk.ca or info@efydesk.ca.We
will help you resolve the issue as soon as possible.
For more information, please visit: https://effydesk.ca/pages/how-to-
assemble-your-height-adjustable-standing-desk
INSTALLATION INSTRUCTIONS
STEP 1
- Separate the Crossbar Ends ⑧ and you will find the Crossbar Rail inside.
STEP 2
- Insert one of the Crossbar Ends into the one of the Lifting Columns ③ and secure with screws.
- Repeat the same step for the other Lifting Column.
STEP 3
- Attach the Side Bracket ⑥ to one of the Lifting Columns.
- Repeat the same step for the other Lifting Column.
STEP 4
- Slide the two Crossbar Ends back into the Crossbar Rail.
- Please make sure they fit into the slots as shown below.
Note: Please make sure the circular holes are facing inwards as shown below.
STEP 5
- Attach both Feet ④ to the bottom of the Lifting Columns.
STEP 6
-
For small/ medium tabletops, use the screws to tighten the Hangers onto the Crossbar.
-
For large tabletops, use the screws to tighten the Hangers onto the Crossbar Rail.
Note: The screws do not go through the Crossbar.Hangers, Allen Key and screws are found in a separate bag.
STEP 7
- Install the tabletop(Pre-drilled/Non pre-drilled).
Note: Please do not over-tighten the screws.
STEP 8
- For large tabletops, use the screws to tighten the middle crossbar.
- For small/medium tabletops, disregard this step.
STEP 9
- Firmly secure the Crossbar with Screws (H) and connect all the cables to the Control Box ①.
Note: Use Zip Ties (D) to secure cables under the table.
STEP 10
- Attach the Cable Tray ⑨ to the Hangers with screws.
STEP 11
- Attach the Keypad ⑦ with Screws (F) to the tabletop.
STEP 12
- Plug the cable from the Keypad into the Control Box and flip the table onto its feet.
Note: The Control Box is equipped with a gyro sensor so the table and the Control Box must be level in order to work properly or else it will not move up or down.
Before plugging in the table, make sure that
- The Lifting Columns are level and set at their lowest position.
- All the screws are tightened to avoid the desk from becoming wobbly.
Calibrate the desk by following the steps below: Please press the Down button and hold for 10-15 seconds until the table stutters and beeps. Release the button. Your desk is ready to use!
Operation Guide
Adjust the table to the desired height, then press M. “S-“ will flash on the display.
Reset the table
When an error code or “RST” appears on the display, p lease reset the table.
- Unplug the power cord from the Control Box.
- Unplug the cable that connects the Keypad to the Control Box.
- Wait 30 minutes and plug all the cables back in.
- Press the Down button and hold for 10-15 seconds until the table stutters and beeps.
If“HOT” appears on the display
- Please unplug and replug and let it cool off for a couple of minutes before proceeding.
If you have any questions, please contact us at
team@effydesk.ca or info@effydesk.ca
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>