effydesk Height-Adjustable Electric Standing Desk Instruction Manual
- June 5, 2024
- EFFYDESK
Table of Contents
Instruction Manual
Technical Data
Segment Column | 3 | Input Voltage | 100-240V |
---|---|---|---|
Maximum Load | 300 lbs | Speed | 35mm/s |
Recommend Load | < 240 lbs | Certification | UL |
Height Range | 600-1250mm |
Accessory List
Tool Required
Parts List
Thank you for your order!
If you have any issues with your product, please feel free to contact us via
team@effydesk.ca or
info@effydesk.ca We will help you resolve the
issue as soon as possible.
For more information, please visit https://effydesk.ca/pages/how-to-assemble-
your-height-adjustable-standing-des
STEP1 Separate the Crossbar ⑧ and you will find the Crossbar Rail inside.
STEP 2
Insert one of the Crossbar Ends into one of the Lifting Columns ③ and secure
it with screws.
Repeat the same step for the other Lifting Column
STEP 3
Attach the Side Bracket ⑥ to one of the Lifting Columns.
Repeat the same step for the other Lifting Column
STEP 4
Slide the two Crossbar Ends back into the Crossbar Rail.
Please make sure to fit the slots as shown below.
Note: Please make sure the circular holes are facing inwards as shown below.
STEP 5
Attach both Feet ④ to the bottom of the Lifting Columns.
STEP 6
For small/ medium tabletops, use the screws to tighten the Hangers onto the
Crossbar.
For large tabletops, use the screws to tighten the Hangers onto the Crossbar.
Note: The screws do not go through the Crossbar. Hangers, Allen Key, and screws are found in a separate bag.
STEP 7
Install the tabletop (Predrilled / Non-predrilled).
Note: Please do not over-
tighten the screws.
STEP 8
Firmly secure the Crossbar with Screws (H) and connect all the cables to the
Control Box ①.
Note : Use Zip Ties (D) to
secure cables under the table.
STEP 9
Attach the Cable Tray ⑨ to the Hangers with screws.
STEP 10
Attach the Keypad ⑦ with Screws (F) to the tabletop.
STEP 11
Plug the cable from the Keypad into the Control Box and flip the table onto
its feet.
Note: The Control Box is equipped with a gyro sensor so the table and the Control Box must be level in order to work properly or else it will not move up and down.
Prepare for First-time Use
Before plugging in the table, make sure that
- The Lifting Columns are level and set at their lowest position.
- All the screws are tightened to avoid the desk becoming wobbly.
- There is no object above or beneath the desk within its range of movement as it may result in physical damage.
Calibrate the desk by following the steps below:
- Please press the Down button and hold for 10-15 seconds until the table stutters and beeps.
- Release the button. Your desk is ready to use!
Operation Guide
Program Presets
- Adjust the table to the desired height, then press M.“S-“ will flash on the display.
- Press a number to set the desired height as a preset.
Advanced Safety Feature: Lock and unlock the table
- Press the Up and Down buttons at the same time for 5 seconds, until “LOC” appears on the display.
- All buttons will be inactivated and no change can be made.
- Press the Up and Down buttons together again to unlock the Keypad and all of the table’s features.
Set Maximum Height Limit
- Raise the desk to the desired maximum height.
- Press M and the Up button together for 5 seconds until you hear a beep. This sets the maximum height limit.
Set Minimum Height Limit
- Lower the desk to the desired minimum height.
- Press M and the Down button together for 5 seconds until you hear a beep. This sets the minimum height limit.
Changing from centimeters to inches
- Press M for 10 seconds and the Keypad will display “1-1”.
- Press the Down button and it will change to “1-0”.
- Press M for 10 seconds to lock the setting.
Reset the table
When an error code or “RST” appears on the display, please reset the
table.
- Unplug the power cord from the Control Box.
- Unplug the cable that connects the Keypad to the Control Box.
- Wait 30 minutes and plug all the cables back in again.
- Press the Down button and hold for 10-15 seconds until the table stutters and beeps.
If“HOT” appears on the display
- Please unplug and replug and let it cool off for a couple of minutes before proceeding.
If you have any questions, please contact us at
team@effydesk.ca or
info@effydesk.ca
www.effydesk.ca
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>