inateck PCL005 Stylus Pencil User Guide
- August 27, 2024
- inateck
Table of Contents
Inateck PCL005 Stylus Pencil
**** Please charge for 5 minutes before use.
Product Diagram
Note:
Before using this stylus pen, please finish the below initial settings on your iPad.
- Make sure that your iPadOS is NOT lower than 12.2;
- Go to Settings – Apple Pencil – Turn off “Only Draw with Apple Pencil”
- Go to Settings – Bluetooth, disconnect the original Apple Pencil.
Magnetic Adsorption
The stylus can be easily attached to the side of an iPad which supports
magnetic attachment function.
Compatible with : iPad Pro 11 inch (1st4th generation), iPad Pro 12.9
inch (3rd6th generation), iPad Air 10.9 inch (4th-5th generation), iPad Mini
(6th generation),iPad Pro 13 (M4)，iPad Pro 11 (M4)，iPad Air 13 (M2) iPad Air
11 (M2).
Disassembly of Stylus Tip
The stylus tip can be easily disassembled/ installed by gently twisting it off.
Power On/Of
Slide the stylus cap up once to turn on the stylus;
Slide the stylus cap up twice continuously to turn off the stylus.
Bluetooth Pairing
Step 1 : Slide the stylus cap up once to turn on the stylus and then the
stylus will automatically enter Bluetooth pairing mode.
Step 2 : On your iPad, go to Settings – Bluetooth – Turn on Bluetooth,
“Inateck PCL005” will appear in the “Other Devices” list at this time.
Step 3 : Click on “Inateck PCL005” in the list, and a “Bluetooth pairing
request” window will pop up. Then, click “Pair”. Once “Inateck PCL005” shows
“Connected” under “My Devices”, it indicates that the connection is
successful.
Check Battery Level
When the stylus is successfully connected to your iPad, you can check the battery level in the following ways:
-
When the iPad is on the home screen, swipe right to Today’s View page, and the remaining battery level of the stylus can be viewed through the battery widget. If there is no battery widget, you can long press the screen to add it.
-
When the iPad is on the home screen, long press the screen to add the battery widget to view the remaining battery level of the stylus.
Sleep Mode
When the stylus is idle for 5 minutes, it will enter sleep mode.
Charging
When the battery widget shows that the battery level of the stylus is lower
than 20%, it is recommended to charge it. You can slide up the stylus cap, and
use the USB cable included in the package for charging.
The battery widget will display the charging status and the stylus can be
fully charged in about 15 minutes.
Product Specifications
| Bluetooth Version | V5.1 |
|---|---|
| Maximum Working Time | About 10h |
| Charging Time | About 15 min |
| Battery Capacity | 100mAh |
| Material | PC, ABS, Aluminum |
| Stylus Tip | Replaceable stylus tip |
Supported Models
| Model | Release Year | Model Number | Software Version |
|---|---|---|---|
| iPad Pro 13 (M4) | 2024.5 | A2925/A2926 A3007 | 17.4 and above |
| iPad Pro 11(M4) | 2024.5 | A2836/A2837 A3006 | 17.4and above |
| iPad Pro 12.9 | 2020.3 |
2018.9
2021.5
2022.10| A2229 /A2233
A2069/A2232
A1876/A2014
A1895/A1983
A2378/A2461
A2379/A2462
A2436/A2437
A2764/A2766| 12 .2 and above
iPad Pro 11| 2020.3
2018.9
2021.5
2022.10| A2228 /A2231
A2068/A2030
A1980/A2013
A1934/A1979
A2377/A2459
A2301/A2460
A2759/A2761
A2435/A2762| 12 . 2 and above
iPad Air 13 (M2)| 2024.5| A2898/A2899 A2900| 17.4and above
iPad Air 11 (M2)| 2024.5| A2902/A2903 A2904| 17.4and above
iPad Air 5| 2022.3| A2588/A2589 A2591| 15.0and above
iPad Air 4| 2020.9| A2316/A2325| 14 .0 and above
iPad Air 3| 2019.5| A2152/A2123 A2153/A2154| 12 .2 and above
iPad Mini 6| 2021.9| A2567/A2568 A2569| 15.0and above
iPad mini 5| 2019.3| A2133/A2124 A2126/A2125| 12 .2 and above
iPad 10| 2022.10| A2696/A2757 A2777/A3162| 16.1and above
iPad 9| 2021.9| A2602/A2604 A2603/A2605| 15.0and above
iPad 8| 2020.9| A2430/A2270 A2428/A2429| 13 . 1 and above
iPad 7| 2019.9| A2197/A2198 A2200| 13 .1 and above
iPad 6| 2018.3| A1893/A1954| 12.1.4 and above
Packing List
Stylus Pencil1
Replacement Stylus Tip1
Instruction Manual1
USB Cable1
FCC Note
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the Users, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.
This equipment complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co- located or conjunction with any other antenna or transmitter.
EU Declaration of Conformity
Inateck Co., Ltd. hereby declares that this device complies with the Directive
2014/53/ EU .
A copy of the Declaration of Conformity can be accessed from https://www.inateck.de/ pages/inateck-euro-compliance.
Battery Safety Warning:
This product contains a built-in rechargeable lithium battery.
Please observe the following safety precautions: do not dismantle, hit, crush,
or expose the battery to fire. If the battery experiences severe swelling,
discontinue use immediately. Avoid placing the battery in high-temperature
environments, and do not use it if it has been immersed in water. During
transportation, do not mix the battery with metallic objects.
Customer Support
North America Inateck Technology Inc.
Tel: +1 (909) 698 7018 (Working day 9 AM – 5 PM PST)
Address: 2078 Francis St., Unit 14-02, Ontario, CA 91761, USA
Manufacturer
Shenzhen Inateck Technology Co., Ltd.
Address: Suite 2507, Block 11 in Tian An Cloud Park, Bantian Street,
Longgang District, Shenzhen, Guangdong, China
Email: product@licheng-tech.com
Postal code: 518129
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>