eMACROS 1/2 Mile Long Range Solar Wireless Driveway Alarm Outdoor Weather Resistant Motion Sensor & Detector-Complete Features/User Guide
- June 5, 2024
- eMACROS
Table of Contents
eMACROS 1/2 Mile Long Range Solar Wireless Driveway Alarm Outdoor Weather
Resistant Motion Sensor & Detector
Specifications
- BRAND : EMACROS
- ACCESSORIES: 1 receiver and 1 sensor
- POWER SOURCE : Solar
- ITEM WEIGHT : 0.64 Ounces
- MAXIMUM RANGE : 30 Feet
- PRODUCT DIMENSIONS: 6.26 x 3.11 x 0.39 inches.
Introduction
Wireless solar driveway alarm and solar driveway alert system uses cutting- edge systems technology. One AC-powered receiver and one sensor are included in this wireless solar driveway alarm. eMACROS is easy to install. The Quick Start Guide will get you up and running in minutes. Up to four sensors and an unlimited number of receivers can be added for complete perimeter coverage. Wireless driveway security system detects human, automobile, and large animal movement. There are four different types of chimes to pick from. To distinguish where driveway alarm wireless motion is being detected, match distinct chimes with different sensors around your home.
This device has been put to the test in real-world scenarios involving trees, buildings, barriers, and cars. In most situations, it easily achieves a wireless range of 1500 feet. It has been put to the test in dense woods, hail storms, strong winds, heavy rains, extreme heat, and snow.
There’s no battery required. The sensor is powered by a built-in rechargeable lithium-ion battery that is charged by the solar panel, thus there is no need to replace the battery. The sensor can also be driven by a DC5V power converter.
Product Description
Installation
Base Station
- Plug the Base Station into an outlet using the AC adapter Base Station can also run on (4)AA batteries for up to 2 weeks, as backup in case of power outage.
- The red power light will illuminate on #3 when the Base Station is on. To turn the Base Station on /off, hold down the power button until you hear the on/off tone.
- Adjust the Base Station volume as needed, using the adjustable Volume +/- buttons. Volume adjustments will be heard on subsequent alarm activations, not while adjustments are being made. Powering off the base station will reset the volume to the factory setting.
Sensor
- Before installing the PIR Sensor, recharge the sensor (with 18650 battery attached) using the AC adapter to ensure a full charge. The blue light will illuminate while charging. The blue light will turn off once the battery is fully charged.
Note : The sensor has been tested several times in the factory. If the blue light wont illuminate, the battery may be fully charged, you can install it directly.
- High/ Low/ Off Switch: First, open the black silicone seal cap at the bottom of the PIR Motion Sensor, then turn on the sensor by switching to High or Low. Set the detection range to High (30feet), Low (20 feet), or turn sensor Off.
- CH 1-4 Switch: Select a different channel for each outside sensor. When detecting movements, a sensor eye will flash red only when assigned to lines 1 and 2, not lines 3 or 4.
Note : Each Separate channel uses a unique chime, allowing you to match different chimes with different channels.
- Test the PIR Motion Sensor by waving your hand in front of the sensor. The Base Station will produce a unique tone based upon the sensor’s setting.
Installing The sensor
- Mount the waterproof PIR Motion Sensor vertically on a solid surface 3-5 feet (1-1.5m) above the ground (rotate sensor to access screw holes). The sensor should be able to swivel as needed. Position the sensor to avoid direct sunlight shining on the sensor eye while simultaneously keeping the solar cell facing upward.
- Vehicle Alert Installation: The best mounting position for detecting vehicles is about 4 feet (1.2m) high. The PIR sensor detects the movements with heat sources; please adjust the sensor eye with a horizontal angle to the engine of the car.
Note : The sensors operate best in the -4F to 140F degree range. The sensors will not work properly outside of this temperature range.
Frequently Asked Questions
-
What is the operation of a wireless driveway alarm?
When a motion sensor detects movement, it sends a wireless signal to a receiver in your home, which sounds an alarm and alerts you that someone is approaching your driveway. -
Will a driveway alarm be triggered by deer
Outdoor motion detectors are set off by animals. This will only happen if the sensor is sensitive enough for animals to activate it -
Why does my driveway alarm continue to sound?
Inspect the driveway for large enough tree branches and other debris to trip the sensor located on one side of the driveway. Remove a nny obstructions from the driveway. -
Do wireless alarms require Internet access?
Instead of connecting to your home’s Internet connection, a wireless GSM home security alarm will connect to the neighboring mobile network. -
Is wireless security superior to wired security?
This question has no one-size-fits-all response, but here’s the gist: Wired security systems have more dependable signals, however wireless security systems are easier to install and can be used in situations where wired security systems cannot.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>