STARLINK GEN 3 Standard Wall Mount User Guide

STARLINK GEN 3 Standard Wall Mount

INSTALLATION AND USING INSTRUCTION

The Starlink Standard Wall Mount is designed for installation on an exterior wall near the top of the gable or fascia. This wall mount can accommodate a 4” overhang maximum and offers a secure, long-reaching platform to optimize the placement of your Starlink for the best connectivity and performance.

Crafted from durable, weather-resistant materials, the mount ensures a sturdy and enduring foundation for your Starlink, capable of withstanding various environmental conditions. Its elongated design allows for greater flexibility in positioning, enabling easy alignment and adjustment to maximize signal reception. Easy to install and adjust, the wall mount comes with all the necessary hardware and instructions, simplifying the setup process for a hassle-free experience.

Compatibility:

• Starlink Standard, Starlink Enterprise,
• 4” Overhang Maximum

Kit Contents:

• Wall Mount, Silicone,
• 2x Lag Screws, 20x Cable Routing Clips

Recommended Tools:

• Drill, 6 mm (1/4 in) Drill Bit,
• 9/16 in Hex Socket, Marker, Level

Package Dimensions:

280 x 470 x 105 mm (1.1 x 18.5 x 4.1 in)

Package Weight:

• 1.6 kg (3.5 lbs)

The Starlink Standard Pivot Mount is perfect for installation on slanted, shingled roofs. Designed for ease of use and flexibility, the Pivot Mount swiveling mechanism enables effortless fine-tuning, adapting to various angles and directions, thus maximizing the performance of your Starlink.

Crafted from durable, weather-resistant materials, the mount ensures a sturdy and enduring foundation for your Starlink, capable of withstanding various environmental conditions. Its elongated design allows for greater flexibility in positioning, enabling easy alignment and adjustment to maximize signal reception. The Pivot Mount is engineered for easy installation and is accompanied by all necessary hardware and user-friendly instructions, ensuring a hassle-free setup process.

Compatibility:

• Starlink Standard, Starlink Enterprise

Kit Contents:

• Pivot Mount, 2x Sealant Tape Squares, 2x Sealant Tape Strips, 2x Lag Screws, 20x Cable Routing Clips

Recommended Tools:

• Drill, 6 mm (1/4 in) Drill Bit,
• 9/16 in Hex Socket, Marker, Level

Package Dimensions:

• 280 x 470 x 105 mm (1.1 x 18.5 x 4.1 in)

Package Weight:

• 1.9 kg (4.2 lbs)

The Starlink Standard Pipe Adapter is designed to attach to any existing pole with a minimum diameter of 31 mm (1.25 in) and a maximum diameter of 63.5 mm (2.5 in). This adaptable and sturdy device allows seamless installation onto a variety of pole sizes, offering flexibility and ease in positioning your Starlink for optimal performance.

Crafted from durable, weather-resistant materials, the mount can ensure a sturdy and enduring foundation for your Starlink, capable of withstanding various environmental conditions.The Starlink Pipe Adapter is engineered for easy installation and is accompanied by all necessary hardware and user- friendly instructions, ensuring a hassle-free setup process.

PIPE NOT INCLUDED. ONLY INTENDED TO BE USED WITH METAL PIPES, NOT PVC AND PLASTIC PIPES

Compatibility:

• Starlink Standard, Starlink Enterprise

Kit Contents:

• Pipe Adapter Mount, Allen Key,
• 20x Cable Routing Clips

Package Dimensions:

• 250 x 179 x 113 mm (9.8 x 7.0 x 4.4 in)|

Package Weight:

• 0.971 kg (2.14 lbs)

The Ridgeline Mount requires no drilling and is designed to sit on the top ridge of a gable roof. Held in place by ballast weights, the mount is ideal when you are unable or unwilling to drill holes in a roof. The mount works great with metal and shingled roofs with slopes less than 45 degrees, but is not recommended for clay tile roofs. With a wind rating of up to 80 kph (50 mph), this mount supports most installation needs.

Compatibility:

• Starlink Standard, Starlink Enterprise

Kit Contents:

• Ridgeline Mount, 4x Ballast Weights,
• 20x Cable Routing Clips

Package Dimensions:

• Mount: 756 x 656 x 101.4 mm (29.8 x 25.8 x 4.0 in) Ballast: 424 x 124 x 189 mm (16.7 x 4.9 x 7.4 in)

Package Weight:

• Mount: 5.8 kg (12.8 lbs)
• Ballast: 25.3 kg (55.8 lbs)

The Mobility Mount is designed to create a waterproof seal and protect against water ingress when permanently mounting to wood, fiberglass, metal, plastic and slotted rails on vehicle racks. The Mobility Mount features stainless steel fasteners, which are corrosion resistant to support harsh environments. This durable and versatile mount also supports an 8 degree mounting angle to maintain a signal during extreme and wet weather conditions.

Compatibility:

• Starlink Standard, Starlink Enterprise

Kit Contents:

• Mobility Mount, Screwdriver , 4x Bolts, 4x Nyloc Nuts, 4x Lag Screws, 4x Seaing Washers

Package Dimensions:

• Mount: 185.5 x 249.9 x 86 mm (7.3 x 9.8 x 3.4 in)

Package Weight:

• Mount: 880 g (1.94 lbs)

The Gen 3 Router introduces WiFi 6 and tri-band radios to Starlink. With improved range, performance, and device support, the Starlink Gen 3 router will extend your WiFi network throughout your home to provide a more consistent and reliable connection with faster speeds and can be purchased to mesh with your existing Starlink router setup. Mesh Compatibility: Compatible with Starlink Gen 2 router and Starlink Gen 3 router. Not compatible with Starlink Gen 1 routers or 3rd party mesh systems.

Compatibility:

• Gen 2 Router, Gen 3 Router

Ethernet Ports:

• Two (2) Latching Ethernet LAN ports with  removable cover

Package Dimensions:

• 361 x 154 x 101 mm (14.25 x 6 x 4 in)

Package Weight:

• 2.7 kg (6 lbs)

The Router Mount is designed to mount the Gen 3 Router directly to a wall or other surface. It is ideal for home or office use when no desk space is available, or for mobility applications where space efficiency is paramount.
Once the Router Mount is installed, the Gen 3 Router is easily snapped into place and cable retention ensures the cables are not accidentally pulled out.

Compatibility:

• Gen 3 Router

Kit Contents:

• Router Mount, 2x Screws,
• 2x Drywall Anchors

Recommended Tools:

• Drill, Marker, #2 Phillips Screwdriver, 4 mm (5/32 in) Drill bit (no anchors) or 7 mm
• (9/32 in) Drill bit (wall anchors)

Package Dimensions:

• 250 x 165 x 85 mm (9.8 x 6.5 x 3.3 in)

Package Weight:

• 0.34 kg (0.75 lbs)

Available to purchase after receiving your order confirmation email.

Frequently Asked Questions

• Q: Can I use the Standard Wall Mount on a flat roof?
  • A: The Standard Wall Mount is specifically designed for installation on an exterior wall near the top of the gable or fascia. It is not recommended for use on flat roofs as it may not provide the intended performance.
• Q: Is the Standard Pivot Mount suitable for all types of roofs?
  • A: The Standard Pivot Mount is ideal for installation on slanted, shingled roofs. It may not be suitable for other roof types, so make sure to assess compatibility before installation.
• Q: What tools are required for installing the Standard Pipe Adapter Mount?
  • A: The recommended tools for installing the Standard Pipe Adapter Mount include a drill, 6 mm (1/4 in) drill bit, 9/16 in hex socket, marker, and level.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>