LOGOSOL B751 Band Sawmill User Manual

: August 24, 2024
: LOGOSOL

Table of Contents

LOGOSOL B751 Band Sawmill
Specifications
Product Usage Instructions
FAQ
ASSEMBLY INSTRUCTION
THROTTLE ADJUSTMENT
CONTACT
Documents / Resources

LOGOSOL B751 Band Sawmill

Specifications

Art. nr: 0458-395-0850
Engine: 13 HP Briggs & Stratton petrol engine
Accessory pack: 8400-000-0063

Product Usage Instructions

Installation of the Petrol Engine

Unscrew the grille from the engine and remove the lower part of the heater grille.
Refit the heater grille on the engine.
Fit the exhaust reflector on the silencer.

Engine and Throttle Cable Installation

Install the engine on the engine shelf using a fastening screws.
Fit the centrifugal clutch, drive belt, and throttle cable on the sawmill.
Install the engine on the saw head before placing it on the rail. Use two people for lifting.
Thread the drive belt around the drive wheel and over the tensioner.
Install the end of the cable in the throttle handle and thread it into the sheath.
Fit the handle on the handle tube.
Cut the wire housing to 1600 mm and pull the wire and wire housing into the handle.

Throttle Adjustment

Turn off the ignition and close the fuel valve before adjusting the throttle cable tension on the engine.
Always start and switch off the machine from the operator’s station.

FAQ

Q: How many people are recommended for lifting heavy parts during installation?

A: Two people are always required to help with heavy lifting to avoid any risk of injury.

Q: What precautions should be taken when handling the engine?

A: Wear protective gloves and handle the engine carefully to prevent any risk of entrapment or injury. Always ensure the engine is placed securely on the engine shelf.

Q: When should the machine be switched off before adjusting the throttle cable tension?

A: Always turn off the machine before adjusting the throttle cable tension on the engine side to prevent any risk of injury or accidents.

This manual describes the installation of the petrol engine for the Logosol band sawmill.
Please see the user manual for your band sawmill for information on assembly, settings, and safety instructions.
8200-000-0050
13 hp petrol engine
Briggs & Stratton
8400-000-0063
Accessory pack, 13 hp
Briggs & Stratton

ASSEMBLY INSTRUCTION

FINAL SAW HEAD ASSEMBLY, 13 HP BRIGGS & STRATTON

Read through all the set-up instructions before starting to set up, then follow the instructions step by step as you work.
After assembly, follow the instructions under the Setup sequence in the sawmill manual to complete the setup before starting the machine.
Unscrew the grille from the engine and remove the lower part of the heater grille as illustrated.
WARNING! Heavy! Risk of injury.
Two people are always required to help with heavy lifting.
WARNING! Risk of entrapment.
Wear protective gloves and handle the engine carefully when placing it down on the engine shelf.

INSTALLATION OF ENGINE AND THROTTLE CABLE

The engine has to be installed on the engine shelf and secured using the fastening screws.
The centrifugal clutch has to be fitted, and the drive belt and throttle cable also have to be fitted on the sawmill.
Follow the assembly instructions, then run through the setup sequence for the machine when the assembly is complete.
Install the engine on the engine shelf: Install the engine on the saw head before placing the saw head on the rail.
Two people are always required to help when the engine is lifted into place. The illustration below shows the hole pattern for installing the 13 hp Briggs engine.
Thread the drive belt around the drive wheel and over the tensioner.
1 x – 9020-011-0091
Install the end of the cable in the throttle handle, then thread it into the sheath.
1 x – 8000-001-6054
1 x – 8000-001-6057
1 x – 8000-001-6060
Fit the handle on the handle tube.
If this handle is fitted: Cut the wire housing to 1600 mm.
Pull the wire and wire housing into the handle as illustrated.

If this handle is installed:

The wire housing = 2900 mm.
Release and unscrew the knob holding the airbox in position.
Release the wing nut and remove the air filter.
WARNING! Risk of serious injury.
Before adjusting the throttle cable tension on the engine: turn the ignition to OFF and close the fuel valve.
Always start the machine from the operator’s station. Always switch off the machine before adjusting the throttle cable tension on the engine side.
WARNING! Risk of burn injuries. The engine and its muffler get very hot during operation and remain hot for a while after shutdown.
Allow the engine and silencer to cool before servicing or performing maintenance on the machine.

THROTTLE ADJUSTMENT

Start by adjusting the throttle cable at the throttle handle so that you have equal adjustment travel in both directions (1)
Attach the other end of the cable housing to the clamp on the engine (2)
Screw the cable into the nipple (3). Make sure that the throttle is in the neutral/unaffected position when doing this.
Check that you have 1 to 3 mm of clearance in the throttle handle and that the cable moves freely. Adjust the cable tension at the throttle handle (1), if necessary
Start the engine and check that it is idling and that the saw blade does not move while the throttle handle is in an idle position. Adjust the cable tension at the throttle handle (1), if necessary
Secure the adjustment using the locking nuts (4)
WARNING! Risk of serious injury.
The hinge switch for the machine has to be fitted before commissioning the machine
Always switch off the machine from the operator’s position before working on the saw head.
WARNING! Risk of burn injuries. The engine and its muffler get very hot during operation and remain hot for a while after shutdown.
Allow the engine and silencer to cool before servicing or performing maintenance on the machine.
Now install the safety hinge on the side of the cover where no hinge is installed. Note that the cable output has to face the middle of the engine shelf.
Now connect the safety switch to the engine as illustrated.
Connect (1) to the lower engine connector.
Then secure (2) to the top screw.
How to check the safety function: Start by opening the cover. Turn the ignition key from the operator’s station to start the engine.
The installation is correct if the engine does not start when the key is turned. Switch off the engine from the operator’s station if the engine starts with the cover open.
Then double-check the connection and contact
Logosol for support.

Well done!

Now you have finished installing the engine, go back to the manual for your band sawmill and carry on with the setup sequence, starting at the point indicated in the instructions below.

SETUP SEQUENCE

Read through all the set-up instructions before starting to set up, then follow the instructions step by step as you work.
IMPORTANT! It is important to adjust the saw head before starting to ensure satisfactory sawing and the correct functioning of the sawmill.
Follow the setup sequence carefully! Certain adjustments affect other machine settings.