LOGOSOL B751 27 HP Petrol Engine User Manual
- June 12, 2024
- LOGOSOL
Table of Contents
ORIGINAL USER MANUAL.
Ref..no: 0458-395-0821
REV: 1
27 HP PETROL
ENGINE
LONCIN
This manual describes installation of the petrol engine for the Logosol
band sawmill.
Please see the user manual for your band sawmill for information on
assembly, settings and safety instructions.
Read through the user manual carefully and make sure you understand its contents before using the saw.
PACK SUPPLIED
01-00779
27 hp petrol engine (incl electric start)
FINAL SAW HEAD ASSEMBLY, 27 HP LONCIN
Read through all the set-up instructions before starting to set up, then
follow the instructions step by step as you work.
Numbering for installation sequence
After assembly, follow the instructions under Setup sequence in the
sawmill manual to complete setup before starting the machine.
WARNING! Heavy! Risk of injury.
Two people are always required to help with heavy lifting.
WARNING! Risk of crushing injury.
**** Wear protective gloves and handle the engine carefully when placing it
down on the engine shelf.
INSTALLATION: ENGINE AND THROTTLE CABLE
The engine has to be installed on the engine shelf and secured using the
fastening screws. The drive belt and the gascable shall be mounted on the
sawmill. Follow the assembly instructions and then go through the machine’s
sequence of settings once assembly is complete.
Fitting the exhaust deflector on the silencer.
3 x – M4x15
Install the engine on the engine shelf: Install the engine on the saw head
before placing the saw head on the rail. Two people are always required to
help when the engine is lifted into place. The illustration below shows the
hole pattern for installing the 27 hp Loncin engine.
4 x – M10x50
4 x – M10
Top view:
Thread the drive belt around the drive wheel and
over the tensioner.
1 x – 9020-011-0091
Install the end of the wire in the throttle handle, then
thread it into the casing.
1 x – 01-00793
Mount the handle on the handle tube.
| 1 x – M6x50
---|---
| 1 x – M5x50
| 1 x – M6
| 1 x – M5
Remove the air filter cover, remove the air filter and unscrew the
plate. Thread the gas wire through the front cover. 
Fit the
throttle link on the cwire retainer, then lock the assembly into position
using the lock washer.
Hang the
throttle link in the outer hole of the throttle (1).
Clamp the wire into the front clamping bracket, closest to the front cover.
NB! Attach it to the inside of the clamp bracket closest to the engine
(2).
WARNING! Risk of serious injury.
The hinge switch for the machine has to be fitted before starting to use
the machine.
Always switch off the machine from the operator’s position before
working on the saw head.
WARNING! Risk of burn injuries. The engine and its silencer become very
hot during operation and remain so after the engine has been shut down.
**** Allow the engine and the silencer to cool to cool before performing
servicing or maintenance on the machine.
Now install the safety hinge on the side of the cover where no hinge is
installed. Note that the cable output has to face the middle of the engine
shelf.
| 2 x – M6x25
---|---
| 2 x – M6x30
| 1 x – 03-01997
| 1 x – 03-02080
| 2 x – 03-02182
MOUNTING: SAFETY SWITCH & ELECTRIC STARTER
Now connect the safety switch to the engine as illustrated.
How to check the safety function: Start by opening the cover. Turn the
ignition key from the operator’s station to start the engine. The installation
is correct if the engine does not start when the key is turned. Switch off the
engine from the operator’s station if the engine starts withthe cover open.
Then double-check the connection. Now connect the battery to the motor
according as illustrated.
2 x – M6x20
2 x – M6
The battery is placed in the protective box and secured using
the strap as illustrated.
Install the shelf for the gas tank using the sawmill’s existing
screws.
Place the
gas tank on the shelf and fasten it with the tensioning strap. Attach the oil
hose to the tank and engine. Before start-up, top up with oil.
WARNING! Risk of serious injury.
Before adjusting the throttle cable tension on the engine: Turn the
ignition to OFF and close the fuel valve.
Always start the machine from the operator’s station. Always turn off
the machine before adjusting the tension of the throttle cable on the engine
side.
WARNING! Risk of burn injuries. The engine and its silencer become very
hot during operation and remain so after the engine has been shut down.
**** Allow the engine and the silencer to cool to cool before performing
servicing or maintenance on the machine.
THROTTLE ADJUSTMENT
- Start by adjusting the throttle cable at the throttle handle so that you have equal adjustment travel in both directions (1).
- Attach the other end of the wire housing to the clamp on the engine (2).
- Screw the wire into the nipple (3). Make sure that the throttle is in the neutral/unaffected position when doing this.
- Check that you have 1 to 3 mm of play in the throttle handle, and that the wire moves freely. Adjust the wire tension at the throttle handle (1), if necessary
- Start the engine and check that it is idling and that the saw blade does not move while the throttle handle is in idle position. Adjust the cable tension at the throttle handle (1), if necessary
- Secure the adjustment using the counter nuts (4)
- Cut off the wire that is left over, save about 30 mm (5).
Well done!
Now you have finished installing the engine, go back to the manual for your
band sawmill and carry on with the setup sequence, starting at the point as
indicated in the instructions below.
ADJUSTMENT SEQUENCE
Read through all the set-up instructions before starting to set up, then
follow the instructions step by step as you work.
IMPORTANT!
It is important to adjust the saw head before starting to ensure satisfactory
sawing and the correct functioning of the sawmill. Carefully follow the
adjustment sequence! Certain adjustments affect other machine settings.
Fiskaregatan 2, SE-871 33 Härnösand, Sweden
+46 611-182 85
info@logosol.com
www.logosol.com
Documents / Resources
|
LOGOSOL B751 27 HP Petrol
Engine
[pdf] User Manual
B751 27 HP Petrol Engine, B751, 27 HP Petrol Engine, HP Petrol Engine, Petrol
Engine, Engine
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>