LOGOSOL 6600-000-7017 Manual Remote Feeding For Electric Saw Instruction Manual
- October 30, 2023
- LOGOSOL
Table of Contents
ASSEMBLY INSTRUCTIONS
Part no. 0458-395-0411
REV:1
MANUAL REMOTE FEEDING
FOR ELECTRIC SAW
COMPONENT PARTS
20| MC6S M8x20| 3| Allen screw|
---|---|---|---|---
19| M6SF M8x20| 3| Flange screw M6SF DIN 6921|
18| LM6MF M8 Fzb| 6| Nylon lock flange nut Fzb|
17| M6MF M8| 4| Flange nut M8 Fzb|
16| BRB 10| 4| Washer 10,5×22 t=2 Fzb|
15| M6S M10x25| 4| Hex screw M6S Fzb|
14| LM6M M10| 4| Hex Nylon Lock Nut Fzb|
13| ISO 4759/3| 1| Washer NB 8x22x1,5|
12| 03-03239| 1| Threaded rod M8x150 8.8 fzb| 1
11| DK-00110| 1| Endcap WN319 G32-M8| 1
10| 04-00407| 1| Knob M8x25| 1
9| 04-00409| 2| Flanged bearing 020 KFLOO4| 1
8| 03-02832| 1| Turn wheel bracket| 1
7| 01-00777| 1| Manual feed chain kit| 4
6| 03-02796| 1| Bracket| 2
5| 03-02797| 1| Cable & Wire mount| 1
4| 03-02813| 1| Crank handle| 1
3| 03-02819| 1| Crankshaft| 1
2| 03-02811| 1| Chassis| 1
1| DS-00169| 1| Handle w.out end cap| 2
Item no.| Art.no.| Qty.| Description| Issue
01-00777
12| LM6MF M8 Fzt| 1| Nylon lock flange nut Fzb|
---|---|---|---|---
11| M6SF M6x16| 4| Flansskruv M6SF DIN 6921|
10| LM6MF M6| 4| Nylon lock flange nut Fzb|
9| ISO 4759/3| 1| Washer NB 8x22x1,5|
8| M6SF M8x35| 1| Flange screw M6SF DIN 6921|
7| 03-03156| 1| Turn wheel plate| 1
6| 04-00561| 1| 05B-1 Z=23 Tension sprocket| 1
5| 03-03159| 1| Spacer D=15,8×8,1 L=18,5| 1
4| 03-03158| 1| Sprocket 05B-1 z=23 d=20 L=14| 1
3| P6SS M6x8| 2| Pin screw|
2| 03-03157| 4| Chainholder| 1
1| 01-00697| 1| Feed Chain (Manual)| 1
Item no.| Art.no.| Qty.| Description| Issu e
BOLTS/NUTS
Definition of the fasteners on following pages.
ADDITIONAL SYMBOLS
The following symbols are used as supplements to the symbols above to describe the design of the parts.
DIMENSIONS/LENGTH
The dimensions of the fasteners are written as a diameter measurement (M) ISO 68-1. For bolts, this is followed by a length measurement. The length of the bolt is measured from below the head to the tip of the bolt.
| (Diameter) | (Length) |
|---|---|
| M8 x | 20 |
ASSEMBLY
The crank handle can be mounted on either the right or left side.
The assembly is partially carried out using the existing screw that connects the strut to the guide rail.
The assembly is partially carried out using the existing screw that connects the support leg to the guide rail.
The top plate of the remote feed can be removed to allow storage of the switch box elsewhere when not in use.
Attach the power cable for the saw unit using the wire bracket on the wire mount.
**** Declaration of Conformity
In accordance with Directive 2006/42/EC, Annex 2A
Logosol AB,
Fiskaregatan 2,
SE-871 33 Härnösand, Sweden
Tel. +46 611 18285
hereby declares that Logosol manual remote feeding for electric saw
has been manufactured in conformity with: the Machinery
Directive 2006/42/EC, the EMC Directive 2014/30/EU and has been manufactured
in conformity with the following harmonised standards:
EN ISO 12100:2010, EN 60204-1:2018
Fredrik Forssberg, CEO, is responsible for technical documentation.
Härnösand, 27-10-2022
Declaration of conformity
Logosol AB,
Fiskaregatan 2,
SE-871 33 Härnösand, Sweden
Tel. +46 611 18285
hereby declares that Logosol manual remote feeding for electric saw has been
manufactured in conformity with:
Supply of Machinery (Safety) Regulations 2008 Electromagnetic Compatibility
Regulations 2016 and has been manufactured in conformity with the following
harmonised standards:
BS EN ISO 12100:2010, BS EN 60204-2:2018 Fredrik Forssberg, CEO, is
responsible for technical documentatio
Härnösand 2022-10-27
Fiskaregatan 2, S-871 33 Härnösand, SWEDEN
Phone +46 611 18285 | [email protected] |
www.logosol.com
Documents / Resources
|
LOGOSOL 6600-000-7017 Manual Remote Feeding For Electric
Saw
[pdf] Instruction Manual
0458-395-0411, 6600-000-7017 Manual Remote Feeding For Electric Saw,
6600-000-7017, Manual Remote Feeding For Electric Saw, 6600-000-7017 Manual
Remote Feeding, Manual Remote Feeding, Remote Feeding
---|---