LOGOSOL 0458-395-0421 Remote Crank Feed Petrol Saw Instruction Manual

LOGOSOL 0458-395-0421 Remote Crank Feed Petrol Saw

COMPONENT PARTS

01-00696

| 1 x| 03-02832
---|---|---
| 1 x| 03-03156
| 1 x| 04-00561
| 1 x| 03-03158
| 2 x| 04-00409
| 1 x| DS-00169
| 1 x| 03-03239
| 1 x| 03-02819
| 1 x| 03-02813
| 1 x| 04-00407
| 1 x| DK-00110
| 1 x| 03-02811
| 1 x| 03-03159
| 1 x| 03-02797
| 1 x| 03-02796
| 4 x| 03-03157
| 1 x| 01-00697, 4 m
| 1 x| 01-00696-skp
| 1 x| 01-00777-skp
| 3 x
6 x
4 x
4 x
1 x
4 x
4 x
3 x| M8x20
M8
M10x25
M10
8x22x1,5
BRB 10
M8
M8x20
---|---|---
| 4 x
4 x
1 x
1 x
1 x| M6
M6x16
8x22x1,5
M8M8x35
---|---|---

Exploded view

01-00696

20| MC6S M8x20| 3| Allen screw|
---|---|---|---|---
19| M6SF M8x20| 3| Flange screw M6SF DIN 6921|
18| LM6MF M8 Fzb| 6| Nylon lock flange nut Fzb|
17| M6MF M8| 4| Flange nut M8 Fzb|
16| BRB10| 4| Washer 10,5×22 t=2 Fzb|
15| M6S M10x25| 4| Hex screw M6S Fzb|
14| LM6M M10| 4| Hex Nylon Lock Nut Fzb|
13| ISO 4759/3| 1| Washer NB 8x22x1,5|
12| 03-03239| 1| Threaded rod M8x150 8.8 fzb| 1
11| DK-00110| 1| Endcap WN319 G32-M8| 1
10| 04-00407| 1| Knob M8x25| 1
9| 04-00409| 2| Flanged bearing 020 KFL004| 1
8| 03-02832| 1| Turn wheel bracket| 1
7| 01-00777| 1| Manual feed chain kit| 4
6| 03-02796| 1| Bracket| 2
5| 03-02797| 1| Cable & Wire mount| 1
4| 03-02813| 1| Crank handle| 1
3| 03-02819| 1| Crankshaft| 1
2| 03-02811| 1| Chassis| 1
1| DS-00169| 1| Handle w.out end cap| 2
Item no.| Art.no.| Qty.| Description| Issue

01-00777

12| LM6MF M8 Fzt| 1| Nylon lock flange nut Fzb|
---|---|---|---|---
11| M6SF M6x16| 4| Flansskruv M6SF DIN 6921|
10| LM6MF M6| 4| Nylon lock flange nut Fzb|
9| ISO 4759/3| 1| Washer NB 8x22x1,5|
8| M6SF M8x35| 1| Flange screw M6SF DIN 6921|
7| 03-03156| 1| Turn wheel plate| 1
6| 04-00561| 1| 05B-1 Z=23 Tension sprocket| 1
5| 03-03159| 1| Spacer D=15,8×8,1 L=18,5| 1
4| 03-03158| 1| Sprocket 05B-1 z=23 d=20 L=14| 1
3| P6SS M6x8| 2| Pin screw|
2| 03-03157| 4| Chainholder| 1
1| 01-00697| 1| Feed Chain (Manual)| 1
Item no.| Art.no.| Qty.| Description| lssu e

BOLTS/NUTS

Definition of the fasteners on following pages.

| Shoulder bolt
---|---
| Cross screw
| Slotted screw
| Locking screw
| Hex nut
| Flange nut
| Flat washer
| Allen screw
| Allen screw (partially threaded)
| Hex bolt
| Hex bolt (partially threaded)
| Flange screw
| Flange screw (partially threaded)
| Carriage bolt

ADDITIONAL SYMBOLS

The following symbols are used as supplements to the symbols above to describe the design of the parts.

  | | |
---|---|---|---
Low| Tensilock| Lock| Countersunk

DIMENSIONS/LENGTH

The dimensions of the fasteners are written as a diameter measurement (M) ISO 68-1. For bolts, this is followed by a length measurement. The length of the bolt is measured from below the head to the tip of the bolt.

ASSEMBLY

01-00696

①

| 1 x| 8x22x1,5
---|---|---
| 1 x| M8x35
| 4 x| M8
| 1 x| M8
| 1 x| 04-00561
| 1 x| 03-03159

②

| 4 x| 04-00409
---|---|---
| 4 x| M10x25
| 4 x| M10
| 4 x| M10

③ Mounting the crank handle

| 1 x| 8x22x1,5
---|---|---
| 1 x| M8x20
| 1 x| M8
| 1 x| 03-03158

The crank handle can be mounted on either the right or left side.

| 1 x| 04-00407
---|---|---

⑥

| 2 x| M8x20
---|---|---
| 2 x| M8

⑦ The assembly is carried out using the existing screw joints on the carriage.

| 2 x| M8x35
---|---|---
| 2 x| M8

To facilitate saw unit maintenance, the wire mount can be removed from the saw carriage without releasing the wire tension

⑧

| 4 x| M6x16
---|---|---
| 4 x| M6
| 1 x| 01-00697, 4 m
| 1 x| 01-00720, 1 m
Required for each 1 m extension

⑨ The assembly is partially carried out using the existing screw that connects the strut to the guide rail.

| 1 x| M8x20
---|---|---
| 1 x| M8

⑩ The assembly is partially carried out using the existing screw joints on the beam

| 2 x| M8x20
---|---|---
| 2 x| M8

⑪

⑫ Tighten the drive chain so thatthere is 6-7 cm between the chains.
In order to adjust the tension, you need to loosen the tensioning mechanism’s flange nut.
Once the adjustment has been made, be sure to re-tighten the flange nut.

⑬

01-00701

| **| 1 x 01-00701, 4 m**
---|---|---

01-00729

| ****| 1 x01-00729, 4,5-6 m
---|---|---

NB! Check that there is a distance of at least 3 mm between the remote throttle pressure control and the throttle control on the chainsaw when idling.

Declaration of Conformity

In accordance with Directive 2006/42/EC, Annex 2A
Logosol AB,
Fiskaregatan 2,
SE-871 33 Härnösand, Sweden
Tel. +46 611 18285

hereby declares that Logosol Manual remote feeding for chainsaw

has been manufactured in conformity with:
the Machinery Directive 2006/42/EC and has been manufactured in conformity with the following harmonised standards: EN ISO 12100:2010

Fredrik Forssberg, CEO, is responsible for technical documentation.

Härnösand, 27-10-2022

Fredrik Forssberg, CEO

Declaration of conformity

Logosol AB,
Fiskaregatan 2,
SE-871 33 Härnösand, Sweden
Tel. +46 611 18285

hereby declares that Logosol Manual remote feeding for chainsaw has been manufactured in conformity with: Supply of Machinery (Safety) Regulations 2008 and has been manufactured in conformity with the following harmonised standards: BS EN ISO 12100:2010
Fredrik Forssberg, CEO, is responsible for the technical files.

Härnösand 2022-10-27

Fredrik Forssberg, CEO

Fiskaregatan 2, S-871 33 Härnösand, SWEDEN
Phone +46 611 18285 | info@logosol.com | www.logosol.com

References

• Portable Sawmills and Woodworking Machinery | LOGOSOL | LOGOSOL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>