iPettie JC-A11 Cat Water Fountain Instruction Manual

iPettie JC-A11 Cat Water Fountain

SPECIFICATIONS

• Product Name: Pet Water Fountain
• Power Input: AC 100V-240V 50/60Hz
• Power Output: DC 5V 1A
• Pump Specification: DC Water Pump
• Power Consumption: 1.5W
• Single Package Size: 22(L) x 21.5(W) x 15.5(H) (CM)
• Single Package Weight: 1.0KG
• Length of Power Cord: About 1.8m
• Shell Material: Environment-friendly ABS resin with high-brightness mirror
• Purification Material: Food grade coconut shell activated carbon for water purification
• Water Capacity: 3L
• Certification for water pump: IPX8
• Certification for the whole machine:
• Certification for power supply:
• Environment-friendly standard:

Name of product components

Product Usage Instruction

• Sponge assembly: Firstly, put the sponge into the fixing bracket; then push the sponge fixing bracket into the pump card groove.
• Water pump assembly: Put the water pump equipped with the sponge into the middle of the water storage bucket, set the circular holes on both sides of the water pump at the bottom pillar of the water storage bucket (pay attention to the direction), and press the front of the pump by hand to ensure that the pump absorbs firmly at the bottom of the bucket. Then put the power plug through the slot, and clip the power cord into the slot and fix it well, and then enclose the leakproof cover, and firmly compress it.
• Fill the water storage bucket with water: Fill appropriate amount of pet drinking water in the water storage bucket, the water level should not exceed the highest level (The maximum water capacity is about 3L).
• Place the water filtering tray on the water storage bucket.
• Remove the filter from the plastic bag and rinse it with cold water several times so as to remove the fine particles generated during transportation.
• Place the cleaned filter upside down in the middle groove of the water filtering tray.
• After assembling the drinking water tray as shown in the instructions before the products leave the factory, insert the USB cable into the power adapter, connect the power adapter to the power socket, and the product starts to run normally after connecting the power.

Control Switch of LED light

• Ordinary Version: when the water pump is lack of water, the circuit can cut off automatically for protection, no LED lights and control switches.
• LED Version: when the water pump is lack of water, the circuit can cut off automatically for protection, with LED lights and control switches. Control switches can control on and off of LED lights; After the LED light is on, it is easier to observe the water level through the window so that users can replenish water in time; and the pet can be guided to drink water at night, and avoid accidentally kicking over the machine at night as well.

Maintenance and adjustment of the water pump

In order to ensure the normal service life of the pump, the pump needs to be cleaned regularly. There is a cylindrical bulge at the back end of the water pump, which is equipped with an induction device for water shortage and power failure protection. Please do not hit and break it with force during cleaning to avoid damage to the function.

1. Remove the cover of the water pump.
2. Remove the current-limiting cover (pay attention to the direction when installing).
3. Remove the water pump impeller.

Use of Attention

• For indoor usage only; Due to the water level induction device equipped inside, the product should be placed on flat ground as far as possible, otherwise it may affect the normal use of the product.
• The power adapter connector should not be soaked.
• The position of the power adapter should be higher than the water dispenser body to prevent water splashing into the plug.
• This machine uses power adapter of 5V, do not use power adapter of other brand.
• Do not allow pets to bite this product.
• It is recommended to place mats under this product in order to reduce noise and splashing.

Maintenance of pet water fountain

• Power must be cut off before cleaning and maintenance.
• Wash gently with water or a clean sponge with diluted neutral detergent.
• The sponge for filtering can only be cleaned with water, never use detergent.
• Do not clean this product with hot water, gasoline, alcohol or organic solvent.
• All casings of this product can be safely washed by dishwasher except water pump and power adapter.

Q&A and Troubleshooting

How often should the filter cartridge be replaced?

• Depending on the user’s usage frequency, it is generally recommended to replace the filter cartridge every 20-30 days.

Why are black particles found in pet water dispensers?

• This is a normal situation. Some fine carbon particles will fall off during the transportation of filter. Therefore, before using filter, customers need to wash it at the front and back several times with tap water.

How often do you need to clean your pet water dispenser?

• It is recommended to clean at least once every two weeks. In areas with hard water quality (It is easy to leave scale on the inner wall of water dispenser by using hard water), please clean it once a week.

How long can the pump motor last for working?

• This machine uses pump motor with long life, the motor can keep on working for 20,000 hours (more than 2 years) under the normal condition. Our warranty period is one year (excluding faults caused by improper use or failure to clean regularly).

Does water dispenser use a lot of electricity every day?

• This product uses ultra-low power pump with an average power consumption of 1.5W. It is calculated by working 24 hours a day continuously. The power consumption in one month is about 1 KWH, and the total power consumption in one year is about 13 KWH.

Does the water dispenser make a lot of noise?

• This product uses ultra-quiet water pump, the noise is about 35 dB when working normally. Power off function during water shortage is included in the product. When too little water is stored, the water dispenser will automatically stop running to avoid abnormal noise caused by air entering the pump. The water dispenser shall be placed on the flat ground as far as possible. If the product is not placed evenly, and the water flow in the drinking water area at the top differs too much from the size setting, the falling water will cause too much noise.

Manufacture: Shenzhen Jincan Pet Products CO., LTD

Add: No.9, Xingye No.3 Road, Fenghuang Fourth Industrial Park, Fuyong Town, Bao’an District, Shenzhen, China.

FREQUENTLY ASKED QUESTIONS

What is the iPettie JC-A11 Cat Water Fountain?

The iPettie JC-A11 Cat Water Fountain is a pet water dispenser designed for house cats. It provides a continuous flow of fresh water and features a modern design and efficient filtration system.

What is the capacity of the iPettie JC-A11 Cat Water Fountain?

The iPettie JC-A11 Cat Water Fountain has a large capacity of 3 liters (101 ounces), making it ideal for households with multiple cats or those who prefer less frequent refilling.

What are the dimensions of the iPettie JC-A11 Cat Water Fountain?

The iPettie JC-A11 Cat Water Fountain measures 8.7 x 8.5 x 6.1 inches, providing a compact yet spacious option for various home settings.

How much does the iPettie JC-A11 Cat Water Fountain weigh?

The iPettie JC-A11 Cat Water Fountain weighs 2.2 pounds, which makes it sturdy yet manageable for moving and cleaning.

What material is the iPettie JC-A11 Cat Water Fountain made of?

The iPettie JC-A11 Cat Water Fountain is made from Acrylonitrile Butadiene Styrene (ABS), a durable and lightweight plastic material.

What type of pump does the iPettie JC-A11 Cat Water Fountain use?

The iPettie JC-A11 Cat Water Fountain features an ultra-low noise, waterproof AC pump, which ensures quiet operation and reliable performance.

What is the power consumption of the iPettie JC-A11 Cat Water Fountain?

The iPettie JC-A11 Cat Water Fountain has a power consumption of 1.5 watts, making it energy-efficient and cost-effective.

What are the input and output voltage specifications for the iPettie JC-A11 Cat Water Fountain?

The iPettie JC-A11 Cat Water Fountain operates with an input voltage of AC 110V / 60Hz and an output voltage of AC 12V.

How often should I clean the iPettie JC-A11 Cat Water Fountain?

It is recommended to clean the iPettie JC-A11 Cat Water Fountain at least once a week to ensure the water remains fresh and to prevent any buildup of dirt or bacteria.

What is the price of the iPettie JC-A11 Cat Water Fountain?

The iPettie JC-A11 Cat Water Fountain is priced at $35.99, which reflects its features and quality.

What warranty does the iPettie JC-A11 Cat Water Fountain come with?

The iPettie JC-A11 Cat Water Fountain includes a 1-year warranty, covering any manufacturing defects or issues during that period.

How does the design of the iPettie JC-A11 Cat Water Fountain benefit cats?

The iPettie JC-A11 Cat Water Fountain is designed to attract cats to drink more water with its continuous flow, which helps improve hydration and overall health.

Can the iPettie JC-A11 Cat Water Fountain be used for small dogs as well?

Although primarily designed for house cats, the iPettie JC-A11 Cat Water Fountain can also be used for small dogs due to its ample capacity and user- friendly design.

How does the ultra-low noise pump in the iPettie JC-A11 Cat Water Fountain enhance its usability?

The ultra-low noise pump in the iPettie JC-A11 Cat Water Fountain ensures that the fountain operates quietly, making it less likely to disturb you or your pets while they drink.

What should I do if the iPettie JC-A11 Cat Water Fountain is not powering on?

Ensure the power adapter is securely connected to both the fountain and the electrical outlet. Test the outlet with another device to confirm it is working. Also, make sure the power button on the fountain is switched on.

VIDEO – PRODUCT OVERVIEW

DOWNLOAD THE PDF LINK: iPettie JC-A11 Cat Water Fountain Instruction Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>