iPettie H3 Hourglass Automatic Cat Food Dispenser User Manual

H3
[Basic Version]
Automatic Cat Feeder
User Manual

Failure to heed these instructions may lead to the product being damaged or personal injury. Please follow the instructions for proper use!

SAFETY INSTRUCTIONS

Read all instructions carefully before attempting to operate this device.
Attention

1. For indoor use ONLY.
2. The device needs to be placed horizontally and firmly, it’s not allowed to tilt to one side, rock, or upside down.
3. Keep device placed in a dry area and do not expose the device under sunlight.
4. DO NOT to place the feeder in a high place to avoid the damage from dropping.
5. DO NOT place any foreign objects in the feeder.
6. To avoid tripping, always keep power cord out of the way of foot traffic.
7. DO NOT place anything on top of this feeder.
8. Ensure there are no barriers near the food outlet to make the pets can be fed normally.

Electricity Safety

1. Please check the power supply before going out.
2. The clock will be maintained for a year if the device is powered off.
3. Please pay attention to the battery display when powered by batteries, users need to replace the batteries when shows on LCD screen.
4. It’s suggested to replace the batteries once a year, for the power will be running off as time goes by.
5. When powered by batteries, it is normal for the electric quantity icon to fluctuate occasionally because of the largetransient current.
6. To prevent electric shock, do not insert the power cord or plug into water or other liquids.
7. The device only supports the use of a 5V/1A adapter; please do not use a non-specific adapter.

Caution

1. Intended for use with dogs or cats ONLY.
2. DO NOT use this feeder with puppies, kittens, dogs or cats with any physical disability.
3. DO NOT recommended for puppies or kittens less than 7 months old or unable to reach the feeding dish.
4. DO NOT allow small children to play with ,in or around feeder.
5. DO NOT eat the desiccant. DO NOT use it if it is damaged.
6. For dry food use ONLY. Works best with 5-12mm food diameter or smaller.
7. DO NOT attempt any repairs or modifications to the feeder.
8. DO NOT immerse the feeder in water at any time, as this can cause damage to the electronic components.
9. Dispose of all packaging material properly. Some items may be packed in poly bags; these bags could cause suffocation; keep away from both children and pets.
10. Check with your veterinarian if you are unsure about the proper MEAL SIZE for your pet.
11. DO NOT operate feeder without Bowl, Food Hopper and Lid securely in place.

WHAT’’S IN THE BOX

1 x Automatic Pet Feeder
1 x 5V Power Adapter
1 x Type-C Cable
1 x Desiccant Bag
1x User Manual

PRODUCT OVERVIEW

SETUP AND ASSEMBLE FEEDER

Lift The Latch
Take out the food hopper and install it by aligning the slot on the base.
Place Desiccant
Open the desiccant box on the top lid, tear off the transparent wrapping paper of the desiccant bag, place it into the box and close the top lid. Plug in Power Adapter

1. Battery power supply: remove the battery cover by releasing the retaining clip, insert 3 good quality alkaline “D” batteries and reinstall the battery cover.
2. Power adapter supply: plug in the power adapter and connect the power cable to the card slot.

*Note: Please use safe and standard alkaline batteries. Do not mix batteries of different specifications and models.
Install Food Bowl
Tilt the base unit back slightly, align the buckle of the food bowl with the base unit to install; the same steps to disassemble.
Fill Pet Food*
Open the top lid, pour fresh dry food into the food hopper, and close the top lid.
Note:** The device only supports 5-12mm dry pet food.

USE INSTRUCTION

Unlock the Panel
Press and hold the Button for 3 seconds to unlock, 30 seconds no operation screen will be automatically locked. Set Current Time

1. Press the Button, the hour digits flashes.
2. Use the Increase/Decrease button or to set the current hour, and then press the Button to save and move to the minutes setting, the minute digits flashes, use the Increase/Decrease button or to set the current minute,and then press the Button to save.

Set Feeding Schedule

1. Program Meal Time :“ 1 “icon flash means setting the first meal, Press or adjust hours and minutes, Press button to confirm.
2. Meal Size : LCD display goes into meal size set mode after setting the meal time “ ” icon illuminate, Press or to select desired, Press button to confirm.
3. Repeat this process for as meal times portions desired (Up to 4 meals and 9 portions).
4. If you do not need to set too much feeding schedule, long press the button to save and exit the set mode.

Check the feeding schedule
In the locked state, press or to check the 1-4 meal feeding schedule, but it cannot be set.
Manual Feed
Unlock the panel, long press button to feed one portion.
Record
Unlock the panel, long press to enter recording mode, the “STATE” indicator light is onand record voice toward the “Mic” hole for up to 10 seconds. If the button is released within 10 seconds, the recording ends immediately.
*Note: If you need to record again, repeat the above steps.
Play Record
Unlock the panel, press to play record once, no play if no record
Cancel Feeding Schedule
Set the portion to be” PORTION: ”then no feed anymore.
Default Meal Settings
Unlock the panel and press the and simultaneously until heard “DiDi” sound, which reset the time and clears the feeding schedule and recording.
Indicator Information

Low Battery Power

LCD Screen Icons Information

| OFF| Battery Uninstalled
---|---|---
ON| With Battery Inside
| ON| Low Battery Power
| ON| Panel Unlock
| ON| Panel Lock
MEAL : 1234| OFF| Meal OFF
ON| Meal ON
FLASH| Meal Seting

Power Off
Unplug and take out the alkaline batteries.
Clean

1. Hold the fuselage steady and pull out the food hopper upward.

2. Disassemble the impeller and feeding mechanism.

3. The main body of the feeder is not dish washer-safe.
   Do not immerse the main body in water, This could damage the internal electronics andcause the batteries to short out, create an electrical shock, or catch fire.

4. Use the dry soft cloth to wipe it, the body is not waterproof, please do not use wet cloth.

5. Make sure all parts of the feeder are completely clean and dry before filling with food.

Assemble

1. Align the triangle mark when installing the impeller.
2. Install the food hopper by aligning the slot on the base.

Replace the desiccant pack
Open the desiccant box cover and replace the desiccant. It is suggested to replace it every month.
Replace Alkaline Batteries
Unplug and open the battery lid at the bottom, then you can replace the batteries.
*warnings:

1. Please keep the food hopper dry after cleaning it.
   Please replace the food on a regular basis if your pets did not eat up.

2. Please clean and maintain your device on a regular basis to prolong the using period of your pet feeder.

TROUBLESHOOTING

What happened to your device| How to check by yourself| How to solve it
---|---|---
No display on LCD Screen| The plug is loose/ No battery inside?| Plug in again/ Install batteries
Feeder faulty| Contact After-sale service
Impeller can not be installed| Food blocked on the installation position| Clear the pet food inside the installation position, align the triangle and reinstall
Food hopper can not be installed| Food blocked on the installation position| Clear the pet food inside the installation position and reinstall
El — Display| Impurities inside food hopper| Clean the impurities inside of food hopper
Food size inapplicable| Ensure to use 5-12mm dry food

PARAMETERS

This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2) this device mustaccept any interference received, including interference that may cause undesired operation.

MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>