TESLA S300 Smart Air Purifier and Fan User Manual

: August 15, 2024
: Tesla

Table of Contents

SAFETY INSTRUCTIONS
PRODUCT OVERVIEW
TECHNICAL SPECIFICATIONS
REMOTE CONTROL
OPERATING INSTRUCTION OF REMOTE CONTROL
WIND OUTLET ADJUSTMENT
INSTALLATION
FILTER REPLACEMENT
DISPLAY PANEL
MAINTENANCE
INFORMATION ABOUT DISPOSAL AND RECYCLING
EU DECLARATION OF CONFORMITY
Documents / Resources

TESLA SMART
AIR PURIFIER AND FAN
USER MANUAL

SAFETY INSTRUCTIONS

WARNING
To prevent fire, electric shock and injury, you must comply with the following requirements. Otherwise, comply with applicable national and local electrical codes.

Children, the elderly and people with disabilities or inexperience should be supervised by aresponsible person when using this device. Children should be supervised to ensure that they do not play with the device as a toy.
Please use a separate outlet according to the current/voltage of the fan. Do not use a multi-purpose socket for simultaneous use with other electrical devices.
If the fan does not work because of a damaged power cord, turn off the power and have a qualified person repair it.
Do not move the fan when removing the plug from the socket.
Do not pull out the plug by the cable. Pull out the plug and do not pull on the cable.
Do not use the fan with a damaged cable or connector. If the cable is damaged, contact customer service.
Keep the cable away from heat sources.
Do not place the cable under carpets or cover it with carpets or similar covers. Route the cable away from the traffic area to avoid tripping over it.
Switch off all controls before removing the plug and remove the plug from the socket if you will not be using the device for a long period of time.
Do not place any objects on the air inlet or outlet. Ensure that the air vents are free of dust, lint, hair and other obstructions that could impair airflow.
The fan should be dry mounted on a horizontal platform and should not be located near sources of heat, corrosive air and moisture. The fan should be 150 mm around to ensure good air circulation.
Do not use the fan outdoors or on wet surfaces.
To avoid danger, do not immerse the fan, power cord or plug in water or other liquids. It is not recommended to use an extension cord unless it has been tested by a qualified person.
Do not use an air cleaner or similar product directly next to the fan.
Do not use any cleaning agents or lubricants on this fan, and unplug the unit before cleaning, transporting or maintaining it.

PRODUCT OVERVIEW

TECHNICAL SPECIFICATIONS

Operating voltage/frequency:	100-240 V ~ 50/60 h
Oscillation:	80±5°
Dimensions:	310x230x592 mm
Rated voltage:	24 V
Rated capacity:	35 W
Timer:	1-8 h
Weight:	2.9 kg
Package contents:	Smart Purifier and Fan, manual, Power adapter

REMOTE CONTROL

| Power button: Turn the fan on and off
---|---
| Fan Mode Max mode, Natural mode, Sleep mode
| Ionizer Purification
| Swing: Start and stop swing
| Increase Airflow Decrease Airflow 9 speed levels to choose from
| Speed Timer 1 to 8 hours of timed shutdown

| The device can be switched on and off by pressing the „ON and OFF“ button.
---|---
| Fan Mode: Press button to choose Max mode,Natural mode, Sleep mode
| Press button to turn on Ionizer purification.
Press again to turn off the ionizer purification.
| Press the „Oscillation“ button on the remote control to switch on the oscillating function. This fan can swing 80 ° left and right. Press this button again to end the shaking process.
| Press the „+“ button on the remote control to increasethe air volume.
Press the „-„ button to decrease the air volume.
There are 9 speed level settings.
| Press the timer button on the remote control to set 1 to 8 hours. After the timer function is set, other functions can be used normály. When the device is turned off, the timing setting is also cancelled.

OPERATING INSTRUCTION OF REMOTE CONTROL

Battery replacement method: as shown in the picture.
Please mind the battery direction.
Battery:
Do not charge the battery.
If swallowed, see a doctor immidiately.

The remote control should be pointed at the remote control signal receiver on the display to maximize the remote control signal. Possible phenomenon

This device may respond to remote control of other devices.
If you use the remote control for this fan, other devices may respond. This is due to overlapping remote control frequencies. There is no quality problem in the product itself. To avoid improper use, keep the remote control away from other electrical equipment during operation.

WIND OUTLET ADJUSTMENT

Hold the fan body with one hand and adjust the wind outlet by 15° in front and behind.
Switch on and off
Connect the power supply, the LED display will light up and the device will switch on.
The device enters standby mode.
Click the host power button, the buzzer beeps once and the fan starts.
Press and hold the power button for 2 seconds, the buzzer beeps twice and the fan stops when you release your hand.
Set the air volume
When the host is operating: Click the button to adjust the air volume from 1 to 9.
Oscillation
When the host is in use, press and hold the screentouch button for 1 second. The buzzer will beep once and the fan will oscillate. Press and hold the screentouch button again for 1 second. Buzzer beeps once and the fan stops oscillating.

INSTALLATION

Please use the fan on a flat platform. Do not place the fan in an unstable place, such as an inclined or soft surface, to avoid damage or malfunctions caused by the fan tipping over.
Avoid blocking the air inlet when using. Stay away from the curtains to avoid objects blocking the air inlet and the fan not working.
Do not place any objects within 30 cm of the air outlet, otherwise the blower effect will be impaired.

FILTER REPLACEMENT

This machine is equipped with an air cleaning filter. Before using the fan, the filter should be installed in the fan so that the air can be cleaned.
Method of installation and replacement of the air purification filter:

Turn the top cover of the filter system counterclockwise to unlock and remove the filter.
Disconnect the old filter from the top cover.
The new filter and the top cover are attached and connected with a clip.
Once assembled, insert it back into the main unit and turn it clockwise to secure it.

DISPLAY PANEL

| Long press for 5 second to enter pairing mode. Wifi indicator will be flash.
---|---
| The fan has a memory function. After a total of 720 hours of operation, the filter indicator lights up. After replacing the filter, long press the power button on the remote control for 5 seconds, after beeping the indicator will turn off and the operating time will be recalculated again.
| Press this button to turn on the ionizer purification. Press again to turn off the ionizer.

MAINTENANCE

Before maintenance work, pull the mains plug out of the socket. Surface
Gently wipe the fan surface with a soft dry cloth If the fan surface is dirty, dilute it with a mild detergent and wipe the fan surface with a soft cloth. Then wipe with a dry, soft cloth.
Air inlet & air outlet
Clean the dust at the air inlet and outlet with a soft brush or vacuum cleaner. If there is too much dust, it may affect the fan.
Remote control
Gently wipe the surface of the remote control with a soft, dry cloth. If you will not be using it for a long time, remove the button battery from the remote control.
Power plug
Clean the plug with a soft, dry cloth.
Storage

After cleaning the device, you can stored it in a plastic bag.
Keep away from vibration and electrical equipment with cooling/heating functions.
Do not expose it to direct sunlight, hot and humid places.
Keep out of reach of children.

INFORMATION ABOUT DISPOSAL AND RECYCLING

This product is marked with the symbol for separate collection. The product must be disposed of in accordance with the regulations for disposal of electrical and electronic equipment (Directive 2012/19/EU on waste electrical and electronic equipment). Disposal together with regular municipal waste is prohibited. Dispose of all electrical and electronic products in accordance with all local and European regulations at the designated collection points which hold the appropriate authorisation and certification in line with the local and legislative regulations. Correct disposal and recycling help to minimise impacts on the environment and human health. Further information regarding disposal can be obtained from the vendor, authorised service centre or local authorities.

EU DECLARATION OF CONFORMITY

Hereby, Tesla Solar s.r.o. declares that the radio equipment type TSL-AC-PUFA is in compliance with EU directives. The full text of the EU declaration of conformity is available at the following internet address: tsl.sh/doc
Connectivity: Wi-Fi 2,4 GHz IEEE 802.11 B/G/N20
Frequency band: 2.400 – 2.480 GHz
Max. radio-frequency power (EIRP): < 20 dBm

TESLA SMART AIR PURIFIER AND FAN
Manufacturer
TESLA Solar s.r.o.
Rubeska 215/1
Praha 9 Vysocany
190 00 Praha
Czech Republic
www.teslasmart.com

Documents / Resources

| TESLA S300 Smart Air Purifier and Fan [pdf] User Manual
S300 Smart Air Purifier and Fan, S300, Smart Air Purifier and Fan, Air Purifier and Fan, Purifier and Fan, and Fan, Fan
---|---