ViewSonic VS18602 Slot in PC Module User Guide
- August 15, 2024
- Viewsonic
Table of Contents
VPC2-O Series
Slot in PC module
Quick Start Guide
VS18602 Slot in PC Module
| Model No. | P/N | Model No. | P/N |
|---|---|---|---|
| VS18602 | VPC27-W53-O1 | VS18604 | VPC25-W33-O1 |
| VS18602 | VPC27-W55-O2 | VS18604 | VPC25-W53-O1 |
| VS18603 | VPC2C-W33-O1 | VS18605 | VPC25-W53-O2 |
Thank you for choosing ViewSonic®
As a world-leading provider of visual solutions, ViewSonic® is dedicated to
exceeding the world’s expectations for technological evolution, innovation,
and simplicity.
At ViewSonic®, we believe that our products have the potential to make a
positive impact in the world, and we are confident that the ViewSonic® product
you have chosen will serve you well.
Once again, thank you for choosing ViewSonic®!
Interface
| Item | Description |
|---|---|
| 1 | TYPE-C (DC5V, 500mA) |
| 2 | RESET |
| 3 | USB 2.0 x 2 (DC5V, 500mA) |
| 4 | USB 3.2 (DC5V, 500mA) |
| 5 | LAN |
| 6 | HDMI |
| 7 | DP |
| 8 | LINE-OUT |
| 9 | HDD/POWER_LED |
| 10 | POWER BUTTON |
Installation
NOTE:
- Please note that the two (2) antennas must be installed on the VPC25/ VPC27
- Please pay attention to the installation direction of the VPC25/VPC27, with the vents facing outwards to avoid damage.
- The VPC products do not support hot swapping. When removing or installing the device, ensure to turn OFF the power supply for both display and the VPC product first.
Internet Connection
Input Selection
To select an Input Source:
- Press INPUT on the remote control, press the setting button on the front panel, or press the setting icon from the toolbar to display the Input Settings menu.
- Press to select PC.
- Press on the remote control, or touch the input source.
- Press on the remote control, or touch a blank area outside of the menu to exit.
USB Connection
Specifications
| Processor | Intel’ Comet Lake-S |
|---|---|
| PCH | H510 |
| Graphic | Integrated Intel’ UHD graphic |
| RAM | 2 x DDR4 SO-DIMM, 32GB (Max) |
| Storage | 1 x NVMe M.2 2280 PCIe SSD |
| 10 ports | 1 x USB Type-C |
(USB 3.2 Gen1, Data Only) 2x USB 2.0,
1 x USB 3.2 Gen1| 1 x USB Type-C
(USB 3.2 Gen2, Data Only) 2x USB 2.0,
1 x USB 3.2 Gen2
1 x DP 1.4 out
1 x HDMI 2.0 out
1 x RJ45 Ethernet (with Intel’ 1219-LM)
1 x Audio jack
2 x External antenna Holes
1 x Power On/Off Button
1 x Reset Button 1 x Power LED
1 x HDD LED
1 x 80 Pin JAE OPS connector
WIFI/BT| 1 x M.2 2230 (with Intel® AX201 WiFi 6 + BT 5.2 module)
Watchdog| Support
vPro/AMT| No| Yes
BIOS| AMI UEFI BIOS
Power| DC in +19V @ 4.74A
60 W (Typical)
Operating Conditions| -5 °C to +45 °C
20% RH ∼ 80% RH non-condensing
Storage Conditions| -20 °C to +80 °C
10% ∼ 80% R.H. non-condensing
Regulatory and Service Information
Compliance Information
This section addresses all connected requirements and statements regarding
regulations. Confirmed corresponding applications shall refer to nameplate
labels and relevant markings on the unit.
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Industry Canada Statement
CAN ICES-003(B) / NMB-003(B)
Contains FCC ID: PD9AX201NG
IC ID: 1000M-AX201NG
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU and Radio Equipment Directive (RED) 2014/53/EU.
https://www.viewsonicglobal.com/public/products_download/safety_compliance/acc/VS18602_CE_DOC.pdf
https://www.viewsonicglobal.com/public/products_download/safety_compliance/acc/VS18603_CE_DOC.pdf
https://www.viewsonicglobal.com/public/products_download/safety_compliance/acc/VS18604_CE_DOC.pdf
https://www.viewsonicglobal.com/public/products_download/safety_compliance/acc/VS18605_CE_DOC.pdf
The following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and
Electronic Equipment Directive 2012/19/EU (WEEE).The mark indicates the
requirement NOT to dispose the equipment as unsorted municipal waste, but use
the return and collection systems according to local law. In all EU member
states, operation of 5150-5350MHz is restricted to indoor use only. This
device should be installed and operated with a minimum distance of 20cm
between the radiator and your body.
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the
use of certain hazardous substances in electrical and electronic equipment
(RoHS2 Directive) and is deemed to comply with the maximum concentration
values issued by the European Technical Adaptation Committee (TAC) as shown
below:
| Substance | Proposed Maximum Concentration | Actual Concentration |
|---|---|---|
| Lead (Pb) | 0.10% | < 0.1% |
| Mercury (Hg) | 0.10% | < 0.1% |
| Cadmium (Cd) | 0.01% | < 0.01% |
| Hexavalent Chromium (Cr6⁺) | 0.10% | < 0.1% |
| Polybrominated biphenyls (PBB) | 0.10% | < 0.1% |
| Polybrominated diphenyl ethers (PBDE) | 0.10% | < 0.1% |
| Bis (2-ethylhexyl) phthalate (DEHP) | 0.10% | < 0.1% |
| Butyl benzyl phthalate (BBP) | 0.10% | < 0.1% |
| Dibutyl phthalate (DBP) | 0.10% | < 0.1% |
| Diisobutyl phthalate (DIBP) | 0.10% | < 0.1% |
Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:
- Copper alloy containing up to 4% lead by weight.
- Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
- Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.
- Lead in dielectric ceramic in capacitors for a rated voltage of 125V AC or 250V DC or higher.
Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India). This product complies
with the “India E-waste Rule 2011” and prohibits use of lead, mercury,
hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl
ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium,
except for the exemptions set in Schedule 2 of the Rule.
Product Disposal at End of Product Life
ViewSonic® respects the environment and is committed to working and living
green. Thank you for being part of Smarter, Greener Computing. Please visit
the ViewSonic® website to learn more.
USA & Canada:
https://www.viewsonic.com/us/company/green/go-green-with-viewsonic/#recycle-
program
Europe:
http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan:
https://recycle.epa.gov.tw/
Customer Servicehttp://www.viewsonic.com/