HOFTRONIC SKU 2707736 PIR Sensor Wall Light User Manual
- August 16, 2024
- HOFTRONIC
Table of Contents
HOFTRONIC SKU 2707736 PIR Sensor Wall Light
Specifications
- Product: Marion PIR Sensor Wall Light
- SKU: 2707736
- Designed for: Indoor and outdoor use
Product Usage Instructions
Safety Instructions
- Ensure the AC/Mains power is NOT connected during installation.
- Installation by a qualified electrician is mandatory, following provided instructions and relevant safety regulations.
- Minors or individuals with a mental disability should not install this product.
- Installation must comply with current IEE wiring regulations and building regulations.
Installation Details
Refer to the provided installation manual for detailed step-by-step
instructions.
Sensor Information
- After turning on the power, the PIR sensor has a warm-up period of 10 seconds before entering auto mode.
- To switch to photocell mode, adjust the LUX to minimum and toggle the product on/off twice within 6 seconds. The sensor will switch to photocell mode, adjustable within the Lux range.
- During photocell mode or auto mode, resetting the sensor to warm-up period can be done by toggling the on/off switch over 6 seconds and then switching on again.
FAQ
-
Q: Can this product be used for both indoor and outdoor applications?
A: Yes, this product is designed for indoor and outdoor use. -
Q: What should I do if the sensor is not functioning properly?
A: If you encounter issues with the sensor, refer to the troubleshooting section in the user manual or contact customer support for assistance. -
Q: Is it safe to install this product without a qualified electrician?
A: No, it is crucial to have a qualified electrician install the product to ensure safety and compliance with regulations.
IMPORTANT SAFETY DETAILS
- Ensure the AC/Mains power is NOT connected and cannot be unexpectedly reconnected during installation.
- This product must be installed by a qualified electrician in accordance with instructions provided and in compliance with recognised electrical and safety regulations relevant to the country it is being installed.
- This product may NOT be installed by minors or people with a mental disability.
- This product must be installed to the current edition of the IEE wiring regulations and relevant building regulations in your country.
- This product is designed for indoor and outdoor use.
INSTALLATION DETAILS
SENSOR INFORMATION
- When you turn the power on, the PIR sensor enters a “warm up” period for 10 seconds and then automatically change into auto mode.
- To change into the photocell mode, adjust the LUX to minimum and switch the product on/off for 2 times within 6 seconds (off-on-off-on). The PIR sensor will automatically change into photocell mode. It can be adjusted with the LUX switching. The effective range is from the moon icon to the sun icon. If you adjust it to the sun icon, the lamp will remain on.
- During photocell mode and auto mode, by switching the on/off switch over 6 seconds and then switch on again , the sensor will reset to warm-up period.
INTENDED USE / APPLICATION
Product designed for the use in households and for other similar general
applications.
MOUNTING
Technical changes reserved. Read the manual before mounting. Mounting should
be performed by an appropriately qualified person. Any activities to be done
with disconnected power supply. Exercise particular caution. Product has a
protective contact/terminal. Failure to connect the protective lead may lead
to electric shock. Mounting diagram: see pictures. Check for proper mechanical
fastening and connection to electrical power prior to first use. The product
can be connected to a supply network which meets energy quality standards as
prescribed by law. To maintain the proper IP protection level, the right
diameter of the power cable should be selected for the cable gland used in the
product.
FUNCTIONAL CHARACTERISTICS
Product can be used indoors and outdoors.
USAGE GUIDELINES / MAINTENANCE
Any maintenance work must be performed when the power supply is cut off and
the product has cooled down. Clean only with soft and dry cloths. Do not use
chemical detergents. Do not cover the product. Ensure free air access. Product
may heat up to a higher temperature. Product can only be supplied by rated
voltage or voltage within the range provided. It’s forbidden to use the
product with damaged protective cover. Product must not be used in
unfavourable conditions, e.g. dust, water, moisture, vibrations, explosive air
atmosphere, fumes, or chemical fumes, etc. Non-demountable product. Not
suitable for independent repairs.
ENVIRONMENTAL PROTECTION
Keep your environment clean. Segregation of post-packaging waste is
recommended.
This labelling indicates the requirement to selectively collect waste
electronic and electrical equipment. Products labelled in this way must not be
disposed of in the same way as other waste under the threat of a fine. These
products may be harmful to the natural environment and health, and require a
special form of recycling/neutralising. Products labelled in this way should
be returned to a collection facility for waste electrical and electronic
goods. Information on collection centres is provided by local authorities or
sellers of such goods. Used items can also be returned to the seller when new
product is purchased, in quantity no larger than the purchased item of the
same type. The above rules regard the EU area. In the case of other countries,
regulations in force in a given country must be applied. Contacting the
distributor of our products in a given area is recommended.
COMMENTS / GUIDELINES
Failure to follow these instructions may result in e.g. fire, burns,
electrical shock, physical injury and other material and non-material damage.
For more information about Hoftronic products visit
www.hoftronic.com. Hoftronic shall not be
responsible for any damage resulting from the failure to follow these
instructions. Hoftronic reserves the right to make changes in the manual – the
current version can be downloaded at
www.hoftronic.com.
DECLARATION OF CONFORMITY
DOCUMENTATION
This product has been manufactured and supplied in compliance with all
relevant regulations and directives applicable to all member states of the
European Union. The product complies with all applicable regulations and rules
in the country of sale.
Formal documentation such as the declaration of conformity, the safety data
sheet and the product test report is available upon request.
CE DECLARATION
The product complies with the following directives:
- LVD: 2014/35/EU
- EMC: 2014/30/EU
- RoHS: 2011/65/EU
The complete Declaration of Conformity Document (DOC) is available upon
request.
Imported by HOF Trading B.V. Fahrenheitstraat 11, 6003 DC Weert , The
Netherlands | Made in China | www.hoftronic.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>