HOFTRONIC 4406561 Double Dimmer Button inclcentral Plate and frame User Manual

USER MANUAL
LED DIMMER DUO

SKU 4406561

IMPORTANT SAFETY DETAILS

1. Hazardous voltage may be present at the output of the dimmer despite setting the dimmer to zero brightness level. Look out and tag the input circuit before accessing the wiring connections. Failure to follow this warning can result in death or serious injury.
2. Ensure the AC/Mains power is NOT connected and cannot be unexpectedly reconnected during installation.
3. This dimmer shall be protected by a 6A or up to a 10A maximum miniature circuit breaker, which is special use with this dimmer.
4. This product must be installed by a qualified electrician in accordance with instructions provided and in compliance with recognised electrical and safety regulations relevant to the country it is being installed.
5. This product may NOT be installed by minors or people with a mental disability.

INSTALLATION DETAILS

ONE WAY OPERATION

1. Disconnect power. Lock out and tag the relevant circuit at the mains switchboard.
2. Remove existing switch from wall.
3. Connect the dimmer in accordance with the wiring diagrams. *the copper conductors for the terminals is 1,0 to 1,5mm rigid wire.
4. Refit switch plate to wall and fit the dimmer knob to the shaft.
5. Reconnect power. Push ON and dim with turning knob.

NOTE:
The Dimmer must always be connected to the LINE side of the load.
Two or more dimmers MUST NOT be connected in parallel or series to control the same load from two different locations.

ELECTRICAL SPECIFICATIONS

step-down converter for extra low-voltage incandescent lamps.
2-100W: dimmable LED lamps.
Compatible loads| Dimmable LED lighting with compatible Electronic
Transformers Incandescent lighting, MV Halogen lamps LV Halogen
Lighting with electronic transformers
Operating Temperature| 0°C – 35°C
Operating Humidity| 10 – 90% R.H.
Mounting Centres| 82mm EU Pattern Plate

NOTE:
Operation at elevated temperatures or voltages may cause the thermal protection circuit to operate. If this happen, decrease the connected load to prevent re-occurance.

MINIMAL BRIGHT LEVEL SETTING

HOW TO SET THE MINIMUM BRIGHT LEVEL:

FEATURES

• Suitable for 1-wayswitching.
• Minimum load down to 2W of capacitive or resistive load, such as Dimmable LED Lighting, Incandescent Lighting, MV Halogen / LV Halogen Lighting with electronic transformers.
• Lamps soft-start operation, to extend longer lifetime for the lamp.
• User setting for the minimum dim Level.
• Complies with IEC EN60669 and International safety standards.

NORMAL OPERATION

Operation of Dimmer Knob and Switch:

Push knob to turn the lamp(s) ON or OFF.
Turn knob right to increase brightness to maximum level.
Turn knob left to decrease brightness to minimum level.

INTENDED USE / APPLICATION

Product designed for the use in households and for other similar general applications.

MOUNTING

Technical changes reserved. Read the manual before mounting. Mounting should be performed by an appropriately qualified person. Any activities to be done with disconnected power supply. Exercise particular caution. Product has a protective contact/terminal. Failure to connect the protective lead may lead to electric shock. Mounting diagram: see pictures. Check for proper mechanical fastening and connection to electrical power prior to first use. The product can be connected to a supply network which meets energy quality standards as prescribed by law. To maintain the proper IP protection level, the right diameter of the power cable should be selected for the cable gland used in the product.

FUNCTIONAL CHARACTERISTICS

Product can only be used indoors.

USAGE GUIDELINES / MAINTENANCE

Any maintenance work must be performed when the power supply is cut off and the product has cooled down. Clean only with soft and dry cloths. Do not use chemical detergents. Do not cover the product. Ensure free air access. Product may heat up to a higher temperature. Product can only be supplied by rated voltage or voltage within the range provided. It’s forbidden to use the product with damaged protective cover. Product must not be used in unfavourable conditions, e.g. dust, water, moisture, vibrations, explosive air atmosphere, fumes, or chemical fumes, etc. Nondemountable product. Not suitable for independent repairs.

ENVIRONMENTAL PROTECTION

Keep your environment clean. Segregation of post-packaging waste is recommended.
This labelling indicates the requirement to selectively collect waste electronic and electrical equipment. Products labelled in this way must not be disposed of in the same way as other waste under the threat of a fine. These products may be harmful to the natural environment and health, and require a special form of recycling/ neutralising. Products labelled in this way should be returned to a collection facility for waste electrical and electronic goods. Information on collection centres is provided by local authorities or sellers of such goods. Used items can also be returned to the
seller when new product is purchased, in quantity no larger than the purchased item of the same type. The above rules regard the EU area. In the case of other countries, regulations in force in a given country must be applied. Contacting the distributor of our products in a given area is recommended.

COMMENTS / GUIDELINES

Failure to follow these instructions may result in e.g. fire, burns, electrical shock, physical injury and other material and non-material damage. For more information about Hoftronic products visit www.hoftronic.com. Hoftronic shall not be responsible for any damage resulting from the failure to follow these instructions. Hoftronic reserves the right to make changes in the manual – the current version can be downloaded at www.hoftronic.com.

DECLARATION OF CONFORMITY

DOCUMENTATION
This product has been manufactured and supplied in compliance with all relevant regulations and directives applicable to all member states of the European Union. The product complies with all applicable regulations and rules in the country of sale. Formal documentation such as the declaration of conformity, the safety data sheet and the product test report is available upon request.

CE DECLARATION
The product complies with the following directives:
LVD: 2014/35/EU
EMC: 2014/30/EU
RoHS: 2011/65/EU
The complete Declaration of Conformity Document (DOC) is available upon request.

Imported by
HOF Trading B.V.
Fahrenheitstraat 11, 6003 DC Weert , The Netherlands
Made in P.R.C.
www.hoftronic.com

References

• HOFTRONIC - HOFTRONIC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>