HOFTRONIC 4406509 Wireless LED Receiver User Manual
- October 30, 2023
- HOFTRONIC
Table of Contents
HOFTRONIC 4406509 Wireless LED Receiver
Product Information
The Wireless LED Receiver, SKU 4406509, is a device used for controlling the dimming of compatible load types, such as dimmable LED lamps, dimmable LED drivers, incandescent lighting, halogen 240V lamps, and low voltage halogen lighting with electronic transformers. It has an input voltage of 100-240VAC, output voltage of 100-240VAC, output current of 1×0.45A max, and output power of 1x100W max. The device has a learning key for pairing with an RF remote and a preset key for setting or deleting the minimum brightness. It should be installed by a qualified electrician in compliance with recognised electrical and safety regulations relevant to the country it is being installed.
IMPORTANT SAFETY DETAILS
- Ensure the AC/Mains power is NOT connected and cannot be unexpectedly reconnected during installation.
- This product must be installed by a qualified electrician in accordance with instructions provided and in compliance with recognised electrical and safety regulations relevant to the country it is being installed.
- This product may NOT be installed by minors or people with a mental disability.
- Don’t expose the device to moisture
Product Usage Instructions
Before installation, ensure that the AC/Mains power is not connected and cannot be unexpectedly reconnected during installation. The product must be installed by a qualified electrician in accordance with the instructions provided.
FUNCTION INTRODUCTION
PRODUCT DATA
INPUT VOLTAGE
|
OUTPUT VOLTAGE
|
OUTPUT CURRENT
|
OUTPUT POWER
|
SIZE(ØXH)
---|---|---|---|---
100-240VAC
|
100-240VAC
|
1×0.45A max
|
1x100W max
|
46.5×19.5mm
Compatible Load Types
The Wireless LED Receiver is compatible with the following load types:
- Dimmable LED lamps with a maximum load of 50W @ 230V or 25W @ 110V
- Dimmable LED drivers with a maximum load of 50W @ 230V or 25W @ 110V
- Incandescent lighting and halogen 240V lamps with a maximum load of 50W @ 230V or 25W @ 110V, or 100W @ 230V or 50W @ 110V
- Low voltage halogen lighting with electronic transformers with a maximum load of 50W @ 230V or 25W @ 110V
Note that the maximum number of LED lamps is further dependent on power factor result when connected to a dimmer. The maximum permitted number of drivers is 50W divided by driver nameplate power rating.
Wiring Diagram
Refer to the wiring diagram provided in the user manual for installation.
- With dimmable LED Light
- With dimmable LED Driver
This phase dimmer adopts trailing edge dimming (reverse phase control), please make sure the connected loads support reverse phase control. Please refer to the user manual of the load or consult the supplier of the load.
Pair/delete the pairing with RF remote
- Do wiring according to connection diagram
- Short press learning key on receiver, then pair with the remote (see the remote’s use manual accordingly), once the receiver and remote are paired, the led lights will flash to indicate successful learning. If this does not work, Short press the learning key on the receiver 3 times, then pair with the remote (see the remote’s use manual accordingly). The led lights will flash to indicate the succesful learning.
- If you wish to disconnect the receiver: Long press the learning key on receiver over 5 seconds until LED light flashes, then delete the learned ID, the receiver will be reset to factory defaults
Setting Minimum Brightness
To set a minimum brightness, adjust the brightness to a level and then press and hold down the Min. Set key on the dimmer until the light flashes. Once set, the light can only be dimmable between this minimum brightness and maximum brightness. The dimming range of this dimmer is 1%-100%, but some load types may flicker when dimmed to 1%, thus a minimum brightness shall be set higher than 1% to avoid flickering during the dimming process.
Delete Minimum Brightness
To delete the minimum brightness, adjust the brightness to maximum level and then press and hold the Min. Set key on the dimmer. The light will flash to indicate a successful reset.
PUSH DIM
If connected with a PUSH switch, click the button to switch ON/OFF lights. Press and hold down the button to increase/decrease light intensity.
PRODUCT DIMENSION
INTENDED USE / APPLICATION
Product designed for the use in households and for other similar general
applications.
MOUNTING
Technical changes reserved. Read the manual before mounting. Mounting should
be performed by an appropriately qualified person. Any activities to be done
with disconnected power supply. Exercise particular caution. Product has a
protective contact/terminal. Failure to connect the protective lead may lead
to electric shock. Mounting diagram: see pictures. Check for proper mechanical
fastening and connection to electrical power prior to first use. The product
can be connected to a supply network which meets energy quality standards as
prescribed by law. To maintain the proper IP protection level, the right
diameter of the power cable should be selected for the cable gland used in the
product.
FUNCTIONAL CHARACTERISTICS
The product can only be used indoors
USAGE GUIDELINES / MAINTENANCE
Any maintenance work must be performed when the power supply is cut off and
the product has cooled down. Clean only with soft and dry cloths. Do not use
chemical detergents. Do not cover the product. Ensure free air access. Product
may heat up to a higher temperature. Product can only be supplied by rated
voltage or voltage within the range provided. It’s forbidden to use the
product with damaged protective cover. Product must not be used in
unfavourable conditions, e.g. dust, water, moisture, vibrations, explosive air
atmosphere, fumes, or chemical fumes, etc. Non-demountable product. Not
suitable for independent repairs.
ENVIRONMENTAL PROTECTION
Keep your environment clean. Segregation of post-packaging waste is recommended. This labelling indicates the requirement to selectively collect waste electronic and electrical equipment. Products labelled in this way must not be disposed of in the same way as other waste under the threat of a fine. These products may be harmful to the natural environment and health, and require a special form of recycling/neutralising. Products labelled in this way should be returned to a collection facility for waste electrical and electronic goods. Information on collection centres is provided by local authorities or sellers of such goods. Used items can also be returned to the seller when new product is purchased, in quantity no larger than the purchased item of the same type. The above rules regard the EU area. In the case of other countries, regulations in force in a given country must be applied. Contacting the distributor of our products in a given area is recommended.
COMMENTS / GUIDELINES
Failure to follow these instructions may result in e.g. fire, burns,
electrical shock, physical injury and other material and non-material damage.
For more information about Hoftronic products visit www.hoftronic.com.
Hoftronic shall not be responsible for any damage resulting from the failure
to follow these instructions. Hoftronic reserves the right to make changes in
the manual – the current version can be downloaded at
www.hoftronic.com.
DECLARATION OF CONFORMITY
This product has been manufactured and supplied in compliance with all relevant regulations and directives applicable to all member states of the European Union. The product complies with all applicable regulations and rules in the country of sale. Formal documentation such as the declaration of conformity, the safety data sheet and the product test report is available upon request.
CE DECLARATION
The product complies with the following
directives:
LVD: 2014/35/EU
EMC: 2014/30/EU
RoHS: 2011/65/EU
The complete Declaration of Conformity Document (DOC) is available upon
request.
Imported by
HOF Trading B.V.
Fahrenheitstraat 11, 6003 DC Weert , The Netherlands
Made in P.R.C.
www.hoftronic.com
Documents / Resources
|
HOFTRONIC 4406509 Wireless LED
Receiver
[pdf] User Manual
4406509 Wireless LED Receiver, 4406509, Wireless LED Receiver, LED Receiver,
Receiver
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>