B-TECH BT9370-SAM130-B Freestanding Videowall Stand For Samsung All in one Installation Guide

BT9370-SAM130-B Freestanding Videowall Stand For Samsung All in one

Specifications

• Dimensions: W.2755mm (108.5) x H.2500mm (98.4) x D.950mm (37.4)
• Weight Capacity: 130kg (286lbs)
• Maximum Height: 330cm
• Website: www.btechavmounts.com

Product Usage Instructions

Installation & Operating Safety Instructions
CAUTION: This mount is intended for use only with the maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury.

Parts List – BT9370-SAM130

Installation Tools Required

• Knife/Cutter
• Level (Optional)

Installation Instructions

Combine Columns
Insert and secure item 13 halfway into the non-threaded end of item 7.
Note: The two joining bars with grub screws go in the front of the column and the 2 joining bars with hex bolts go in the back.

Combine Rails

1. On one side of item 19, insert 4x item 22 half-way into each channel.
2.  Slide item 20 onto item 22 and tighten all the grub screws, combining the rails securely.
3. Attach Joining Plates to Columns On item 15, assemble 4x item 17 to item
4. Lay the column on the floor and fit item 15 to items  Repeat for both columns.

FAQ – Frequently Asked Question
Q: Can I use this floor stand for displays other than Samsung’s All-In-One IAC 130?
A: No, this floor stand is specifically designed for Samsung’s All-In-One IAC 130 display.

BT9370-SAM130
FLOOR STAND
FOR SAMSUNG’S ALL-IN-ONE IAC 130″ DISPLAY
INSTALLATION GUIDE

SPECIFICATIONS

• Designed and configured specifically for the Samsung All-in-One IAC 130″ Display
• Created from System X components
• Incorporates Samsung 130″ All-in-One IAC Series mounting brackets
• Adjustable levelling feet to accomodate uneven floor surfaces
• Integrated cable management for a neat
• Dimensions: W. 2755mm (108.5″) x H.2500mm (98.4″) x D.950mm (37.4″)

INSTALLATION & OPERATING SAFETY INSTRUCTIONS

• CAUTION: This mount is intended for use only with the  maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury.
• Do not attempt to install this product until all instructions and warnings have been read and properly understood.
• Please keep these instructions for future reference.
• Please check carefully to make sure there are no missing or defective parts – defective parts must never be used.
• B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
• Check with the place of purchase for information on any guarantees, repairs or replacements of this product.

General

• B-Tech AV Mounts recommends that a professional AV installer or other suitably qualified person install this product.
• Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and easily damaged if dropped.
• If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious injury or death, both during installation and at any time thereafter.
• Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing.
• This weight limit will be clearly stated on each product and its packaging and will vary from product to product.

Product location
Please pay careful attention to where this product is located. Designed for indoor use, this stand is suitable for public or home installation. Check load capacity of the floor prior to installation to ensure that it can support the combined weight
of the equipment and hardware, some surfaces are not suitable for installation.
When verifying the stability of the structure, consider the following external factors: The strength of the floor, exposure to sudden and severe wind and danger arising from contact with people and / or objects (eg installations in passageways, emergency exits), if located in a public or frequently populated area ensure that the product is out of the immediate reach
of people. When drilling holes it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures
when you are sure it is safe to do so.

Fixing hardware
It is highly recommended that all fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models
of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for  each specific installation.
If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.

Hazard limitation
When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other
body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up. Immediately after installation double-check that the work done is safe and secure. Double- check all
necessary fixings are present and are of ample tightness.

Operating & Maintenance
It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more than 6 months apart) to ensure that safety is maintained. B-Tech AV Mounts recommends that a suitably qualified person is used for the removal of this product. Please dispose of the product and packaging carefully and with consideration to the environment. If in doubt consult a professional AV installer or other suitably qualified person.
B-Tech AV Mounts recommends that this product be installed by a qualified AV technician or other suitably qualified person. B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire. This product must be mounted on a suitable surface and may only be used up to the specified maximum weight.

BT9370-SAM130 PARTS LIST

PLEASE KEEP THIS FOR FUTURE REFERENCE

CABINET FIXING KIT
23| SAMSUNG MOUNTING PLATE*| 4
24| M6 SLIDING NUT| 28
25| M6 WASHER| 28
26| M6 x 10mm SCREW| 24
27| M6 x 16mm SCREW| 4

INSTALLATION INSTRUCTIONS

1. COMBINE COLUMNS

2. Insert and secure item 13 halfway into the non-threaded end of item 7.
   Note: The two joining bars with grub screws go in the front of the column and the  joining bars with hex bolts go in the back.

3. Fit item 11 onto the top of item 7 using item 13 and tighten all fixings on item 13. Repeat for both sets of columns.

4. 2. COMBINE RAILS

5. On one side of item 19, insert 4x item 22 half-way into each channel. On the back side of item 19, insert 1x item 22 into the top channel and 1x item 22 into the third channel (see fig. 1).
   Loosely fasten the grub screws on each joining bar securing it to the mounting rail.

6. Slide tem 20 onto item 22 and tighten all the grub screws, combining the rails securely.

7. ATTACH JOINING PLATES TO COLUMNS

8. On item 15, assemble 4x item 17 to item 16.

9. Lay the column on the floor and fit item 15 to items 7 & 11 (see fig 2. for placement of item 15). Repeat for both columns.

10. INSERT SLIDING NUTS INTO MOUNTING RAILS
    Lay the rail on the floor and at either end insert 4x item 16 into item 19.
    Two in the 2nd channel and two in the bottom channel (See fig. 3 for positioning of item 16). Repeat for both rails.

11. ATTACH COLUMNS TO RAILS
    On the floor, place items 7 & 11 onto items 19 & 20. Fix item 15 to items 19 & 20 by fastening item 17 into item 16.
    Note: To ensure straight assembly of items 19 & 20 make sure the distance of items 15 to the end of items 19 & 20 are set the same on each rail.

12. ASSEMBLE BASES TO COLUMNS
    Attach item 1 to item 7 using items 3 & 4.
    Once bases are fixed to columns, return stand to upright position.

13. ATTACH SAMSUNG WALL PLATES TO TOP MOUNTING RAIL

14. On the top rail, insert 24x item 24 into the top channel of item 19 & 20 (See fig.4 for positioning of item 24).

15. Using items 24, 25 & 26, fix 4x items 23 (supplied with screen) to items 19 & 20 (See fig.5).

16. On the lower rail, insert 2x item 24 into the bottom channel of items 19 & 20.
    Note: Refer to fig.6 for the locations of item 24.

17. HOOK THE SAMSUNG FRAME ONTO STAND

18. Following the installation instructions of the Display, hook the Samsung frame onto item 23.

19. Fix the bottom of the frame to the lower rail (items 19 & 20) using items 24, 25 & 27 and the holder ring (supplied with the Samsung display*).

• Please refer to the display’s assembly manual. 3. Follow the display’s assembly manual to complete the screen installation. 9. ADD COVERS AND END CAPS
  1. After screen cables are connected and routed down the back of item 7, partially clip on the cable management item 9, this allows easy removal if more cables need adding. Once satisfied all cables are fitted, clip the covers on fully.
  2. Fit items 10 to the top of item 7.
  3. Fit items 20 to the ends of item 19.
  4. With a knife, cut to length item 8 and insert to the front and sides of item 7.

BT9370-sam130 DIMENSIONS

PLEASE KEEP THIS FOR FUTURE REFERENCE

THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.

CONTACT:
info@btechavmounts.com

©2024 B-Tech International Design and Manufacturing Ltd. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design and Manufacturing Ltd. B-Tech AV Mounts and the B-Tech logo are registered trade marks.
All other brands and product names are trademarks of their respective owners. Photographs are for illustrative purposes only. E&OE.
AMA-BT9370-SAM130-V1-PROBX-0124-BTECH MADE IN VIETNAM

References

• B-Tech AV Mounts - B-Tech International

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>