teesa TSA5050 Smart Vac 2 Owner’s Manual

: August 14, 2024
: teesa

teesa TSA5050 Smart Vac 2 Owner’s Manual

Thank you for purchasing TEESA appliance. Please read this operation instruction carefully before use, an d keep it for future use. Distributor does not take responsibility for damages caused by inappropriate handling and use of the product.

SAFETY INSTRUCTIONS

In order to reduce the injuries or damages, follow basic safety precautions applied when using any electrical device, including the following:

Read this instruction manual carefully, even if you are familiar with the appliance. Keep the manual for future reference.
Before connecting the appliance to power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
Product intended for household use only.
Clean and store this appliance in accordance to instructions listed in “Cleaning and storage” section.
ALWAYS turn off the appliance and disconnect it from the mains supply:
• if it’s not operating correctly,
• if there’s an uncommon voice when using,before disassembling the device,
• before cleaning,
• when not in use.
When you disconnect the power cord of the appliance, grasp and pull the plug, not the cord/cable.
This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device. Children should not perform cleaning and servicing of the device unsupervised.
Keep the appliance out of the reach of children.
Ue only the included AC adapter to charge the device.
Keep the appliance and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
Make sure the power cord does not touch any hot or sharp elements.
Do not use the product for purposes different from displayed in this operating manual.
Do not place the appliance in water or any liquid; nor handle/use it with wet or moist hands.
DO NOT use this appliance if the cord or the plug is damaged, or the appliance is broken.
Do not attempt to repair this appliance yourself. Only authorized and qualified personnel may repair this appliance. Never disassemble this appliance.
Do not use unauthorized accessories

IMPORTANT

Do not use the appliance to vacuum up:
• large, sharp-edged objects which could block and damage the appliance;
• construction waste;
• harming or erodent liquids or inflammable and explosive substances, as this could cause a fire;
• hot or burning substances;
• wet surfaces or wet objects;
• water or any other liquid
Use the robot vacuum cleaner on hard floors and low pile carpets only.
Use the appliance only on dry surfaces.
The appliance is suitable for indoor use only.
Do not insert any objects into the ventilation slots or openings.
Do not obstruct the airflow.
Do not cover the sensors in any way.
Keep hair, loose clothing and any other part of body away from the openings and moving parts.
Do not place the appliance on stairs or furniture.
Do not sit, stand or put any objects on the appliance.
Remember that the robot moves on its own. Exercise caution when walking in the area where the appliance is operating to avoid stepping on it or tripping over it.
Make sure to turn off the appliance before installing or removing brushes.
If the product is not going to be used for a long time please set the power switch to 0 position.
Do not use the appliance if dust bin and filter are not mounted.
Prior to using the robot vacuum cleaner, prepare the room to be cleaned properly. Please be sure that there are no cables, clothes, curtain belts or any other material scattered in the cleaning area to avoid tangling or trapping the appliance during cleaning.
Make sure that there are no fragile or small objects, lit candles, etc. on the surface to be cleaned or on the furniture in the room to be cleaned to avoid damage.
If the room to be cleaned contains a balcony, a physical barrier should be used to prevent access to the balcony and ensure safe operation.
Make sure that children and pets do not have an access to the room where the appliance is operating

*** Environmental conditions such as exposure to sunlight may influence cliff sensor operation. Therefore it is important to ensure safe operation for the robot vacuum cleaner. If in the room to be cleaned there are stairs, balcony or any other places where the appliance is exposed to a fall, use a physical barrier so that in case of cliff sensor malfunction, the appliance will not get damaged.

PRODUCT DESCRIPTION

TEESA SMART VAC 2

Top view

Bumper
IR sensor
ON/OFF button/ LED indicator
Upper cover

Bottom view

Cliff sensors
Side brushes
Front wheel
Suction intake
Dustbin
5a. Premilinary filter
5b. HEPA 11 filter
5c. HEPA 11 filter seal
Power switch
Charging socket

CHARGING DOCK

LED indicator
Signal emission area
Charging pins
Bottom cover
Wire slots
Power socket

REMOTE CONTROL

Start/stop automatic cleaning
Auto docking and charging: the appliance will automatically return to the charging dock and start recharging
Start operation, press again to stop and enter standby mode
Direction buttons: manually navigate the appliance (in operation and standby mode)
Activate spot cleaning mode
Actiate random cleaning mode
Activate edge cleaning mode
Suction power adjustment (two levels available)
Locate the appliance. When you press this button, the appliance will issue a voice prompt which can help you locate it

REMOTE CONTROL BATTERY INSTALLATION

Remove the battery cover at the back of the remote control.
Insert 2x AAA battery with correct polarization.
Reattach the battery cover.

Notes:

Always point the IR sensor of the remote control towards the IR sensor on the front of the appliance.
Use only specified batteries.
Do not mix different types of batteries.
Repace all batteries at the same time.
Please remove the batteries if the remote control is not going to be used for a long time.

INSTALLATION

Charging dock

Remove the cover at the bottom of the charging dock.
Connect the plug of the AC adapter to the power socket and put the excess cable inside the compartment. Afterwards, reattach the cover.
If the excess cable will not be put into the slot, the appliance may stuck during charging or cleaning. Make sure charging dock is ALWAYS plugged in. Otherwise, the appliance will not return to the dock automatically
Place the charging dock against the wall on a floor and connect the AC adapter to the power outlet.
Notes:
• Ensure a space of above 0,5 m on both sides of the charging dock and a space of above 1,5 m in the front. Make sure that space will be easily accessible for the appliance.
• Make sure the cable of the AC adapter is not lying flat on the floor as it may be dragged by the more than 0,5 m appliance and consequently the charging dock may be powered off.
• LED indicator on the charging dock is on when the more than 1,5 m more than 0,5 m charging dock is plugged in.
Please do not move the charging dock arbitrarily and keep it out of direct sunlight.
Notes :
• If the charging dock is relocated, the appliance may fail to locate it.
• Direct sunlight will interfere with recharging signal and consequently the appliance may be unableto return to the charging dock.

Clean the charging pins of the charging dock regularly to avoid malfunction.

Side brushes

Make the left side brush (L) and the right side brush (R) correspond to L and R on the bottom casing.
Press the L and R side brushes into corresponding slots until they lock in place. If you hear a clicking sound that means that the brushes have been installed correctly.

CHARGING

You can charge the appliance in two ways:

By directly connecting the appliance to power supply
Connect one plug of the AC adapter to the power socket of the appliance; connect the other plug to the wall outlet.
Using charging dock (automatic charging)
Make sure the charging dock is correctly installed and connected to the power supply (LED is on).
When the appliance is operating, and the battery level gets low, the appliance will automatically return to the charging dock.

Press the button on the remote control and the appliance will return to the charging dock for recharge.
You can also manually put the appliance on the charging dock. Make sure that the charging pins on the bottom of the appliance align with the charging pins on the charging dock.

LED indicator

Color	Battery status
Flashing red	Charging in progress
Solid blue	Charging finished, battery fully charged

Notes:

When the battery is low, there will be a voice notification and red LED will flash for a few times. The appliance will not start working in that state.
When charging for the first time, make sure that it is charged for at least 6 hours.
Make sure to fully charge the appliance before first use.
If the appliance is not used, charge the appliance every 5 weeks to protect the battery.

OPERATION

Power on: First set the power switch to I position.
Str cleaning: Press the ON/OFF button on the appliance or the start
stop / AUTO button on the remote control. The appliance starts automatic cleaning. Blue LED on the appliance flashes. When the battery level gets low, the appliance will automatically return to the charging dock for recharge. Stop cleaning: When the appliance is operating, press the ON/OFF button on the appliance or the / AUTO button on the remote control to stop operation. The appliance enters standby mode.

Power off: Set the power switch to 0 position.

Suction power control: Press the button on the remote control to select between two the available levels.
Navigating the appliance manually (in standby mode): Use direction buttons on the remote control to manually control the appliance.

Keep the ▲button pressed, so that the appliance will move forward.
Use the ◀▶ buttons to turn left/right.
Press the▼ to move backwards.

Note: You can also use the direction buttons during automatic cleaning (◀▼ ▶ ) to adjust the appliance’s path.

Cleaning modes
The appliance has been equipped with three cleaning modes. Use the remote control to choose one of them.

CLEANING

Prior to cleaning make sure the appliance is turned off (the power switch is in 0 position).

Side brushes

Turn over the appliance and pull out the side brushes upwards.
Clean them from any hair, debris or threads which have been entangled around the shaft. The side brushes can be rinsed under running water. In such case, always make sure to dry them completely.
When the side brushes are clean and dry, push them onto the shaft until you hear a click (always match the symbol L and R on the brush to correspond to the position of L and R at the bottom of the appliance respectively).
If the side brushes are worn and as a consequence cleaning performance deteriorates, replace them with new ones*.

One extra pair of side brushes is included in the set. Side brushes are available to be purchased online at www.teesa.pl lub | www.rebelelectro.com

Dustbin and filters

**** Empty the dustbin after each use!

Push the upper cover in the designated
Grasp the dustbin handle and take out place- it will open automatically. the dustbin.
Unlock the clip at the side of the dustbin and open its cover.
Take out the preliminary filter. Rinse it under running water. Let it dry completely in the shade.
Remove the HEPA filter and the seal. Rinse them under running water. Let them dry completely in the shade.

• It is recommended to clean the filters every 3 weeks.
• HEPA filter can be washed under running water up to 50 times.
• The maximum lifespan of the HEPA filter is 12 months. Thereafter, replace it with a new one.
• Replace it also when you notice significant deterioration in cleaning performance.
• HEPA filter is available to be purchased online at www.teesa.pl lub www.rebelelectro.com

Empty the dustbin and rinse it under running water. Wipe it well with a soft cloth or let it dry completely in the shade.
When all parts are clean and completely dry**, put the filters back into place and close the dustbin lid (make sure you hear a click). Put the dustbin back into the appliance.
Close the upper cover (make sure it clicks and locks in place).

** DO NOT INSERT WET OR SLIGHTLY MOIST PARTS INTO THE APPLIANCE AS THIS BRINGS THE RISK OF ELECTRIC SHOCK AND CAN DAMAGE THE APPLIANCE.

Air inlet

Check regularly for any dust and debris in the suction intake. Make sure the suction intake is not blocked by any foreign body.

Sensors

There are three sensors at the bottom of the appliance (see the exact location shown below). Gently wipe the sensors with a dry, soft cloth.

**It is crucial for proper operation of the appliance to keep the sensors clean all the time. Otherwise, the appliance may malfunction

**

Wheels

Clean the wheels with a cleaning brush or with a soft, dry cloth. If wheels are blocked by a foreign body, use a rod or tweezers and carefully remove it.

Charging dock

Wipe the signal emission area as well as the charging pins (including those on the bottom of the appliance) with a soft, dry cloth.

SPECIFICATION

Main features

For multiple hard floor types and low pile carpets
Washable HEPA filter
3 clening modes
Two side brushes
Cliff sensor
Charging indicator
Voice notifications
Auto docking and charging
Overcoming obstacles up to 1,2 cm
Low profile design (7,7 cm)
Rubber bumper
- - - - Navigating with remote control (2x AAA battery, not included)

Technical data

Suction power	1000 Pa (2 levels)
Filter	HEPA 11
Dustbin capacity	200 ml
Cleaning area	90 m2
Operation time	70 – 90 min
Charging time	approx. 4 – 6 h
Noise level	52 dB
In set	remote control, 2 pairs of side brushes, cleaning brush, charging

dock, AC adapter
Weight| 1,6 kg
Dimensions| ø28 x 7,7 cm

Power supply

Power	15 W
Battery	9,6 V; 2000 mAh

AC adapter:
Input| 00 – 240 V~; 50/60 Hz
Output| 12 V / 580 mA

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or Its literature, indicates that It should not be disposed with other household wastes at the end of its working life. To prevent possible harm lo the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal.

Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwoliska 1, 08-400 Mitne.