teesa TSA3543 Portable Cordless Blender Instruction Manual
- May 15, 2024
- teesa
Table of Contents
teesa TSA3543 Portable Cordless Blender
Thank you for purchasing TEESA appliance. Please read this operation instruction carefully before use, and keep it for future use. Distributor does not take responsibility for damages caused by inappropriate handling anduse of the product.
SAFETY INSTRUCTIONS
In order to reduce the injuries or damages, follow basic safety precautions applied when using any electrical device, including the following:
- Read the entire instruction manual before you start installation and assembly and keep it for future reference. Keep the manual for future reference.
- Device for indoor use only.
- Place the device on a flat and stable surface.
- Do not place the device on fragile or soft surfaces.
- Clean this device in accordance to instructions listed in Cleaning section.
- ALWAYS turn off the device and disconnect it from the mains supply:
- if it’s not operating correctly
- if there’s an uncommon voice when using
- before disassembling the device
- before cleaning
- when not in use
- Keep the device out of the reach of children. Do not leave children unsupervised with the product.
- This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner for all the safety precautions being understood and followed. Children should be supervised to ensure that they do not play with the appliance. Children should not perform cleaning and servicing of the device unsupervised.
- Do not place the appliance in water or any liquid; nor handle/use it with wet or moist hands.
- Do not use the product for purposes different from displayed in this operating manual.
- Do not leave the appliance unattended when it’s working.
- Producer of this product is not responsible for damages caused by inappropriate handling and using of the device.
- DO NOT use this device if it is broken.
- Do not attempt to repair this device yourself. Only authorized and qualified personnel may repair this device. The device has no user serviceable parts inside.
- Use only authorized accessories.
- This device is suitable exclusively for food preparation. Do not place inside the device anything that is not food.
- Always securely clamp in place all parts before the motor is turned on. Do not disassemble while the device is operating.
- Do not touch moving parts. Make sure the motor stops completely before disassembling.
- Use only original attachment /accessories.
- Do not operate with empty-load or over-load.
- Handle the blade with care –it is very sharp.
Product Overview
- Cup
- Blades
- ON/OFF touch button / LED indicator
- Micro USB charging port
CHARGING
Fully charge the appliance before first use.
-
Open the rubber plug at the bottom of the blender’s motor unit.
-
Connect the included micro USB cable to the micro USB port at the bottom of the motor unit. Connect the other plug to the AC adapter and to the wall outlet or a compatible PC USB port.
-
During charging red LED is on.
-
When the battery is fully charged, blue LED is on.
-
Disconnect the blender from power supply and close the rubber plug tightly.
Notes :- Charging takes approximately 4 hours.
- It is not possible to turn on the appliance during charging.
- When red LED lights up during use and the appliance stops, that means that the battery level is low and the appliance must be charged immediately.
OPERATION
Before first use: Wash all the parts that will have contact with food. Rinse them thoroughly with warm water and allow to air dry. Never submerge the motor unit in water or any other liquid!
-
Place the motor unit on a flat and stable surface.
-
Properly prepare the food to be processed. Peel it, remove seeds if necessary and cut it into small pieces.
-
Put the food in the cup then add liquid (e.g. milk, water, juice). Do not exceed the MAX line. For proper operation, the cup should be filled in 80% maximally.
Notes:- Red LED flashes and the blender does not start if the cup is overfilled.
- Never start the appliance if liquid is not added to the cup.
-
Flip the motor unit upside down and install it on the cup. Proper assembly is indicated by the LED flashing red and blue once quickly.
Note : The appliance has a protection against accidental switch on. If the cup is not installed on the motor unit or is installed improperly, the appliance will not turn on. -
With the blender flipped upside down (so that the blades can start with no load), tap the ON/OFF touch button twice to turn on the blender (blue LED is on).
Note : If during operation or when starting the blender, red LED flashes and the appliance stops, that means that the protection has been activated. It may be because the pulp get stuck in blades. Make sure to start the blender as described above. -
After starting, flip it back to its starting position. Then shake the blender left and right.
Note : The appliance stops in less than 30 seconds after start-up and the blue LED flashes what means that the cup is empty or the load is too light. -
The blender will run for approximately 30 seconds and then automatically stop*. You can stop blending earlier, by pressing the ON/OFF touch button once. The appliance may be used continuously about 4 times. Afterwards, stop the appliance and let it cool down for about 10 minutes.
-
When blending is finished, detach the motor unit from the cup by turning it anticlockwise.
CLEANING AND MAINTENANCE
- Remove the cup from the motor unit by turning it anticlockwise.
- Rinse the cup under running water or wash it in a dishwasher. Let it dry completely.
- Wipe the motor unit with a soft, slightly wet cloth or rinse it under running water.
- Do not immerse the motor unit in water or any other liquid!
- To clean the blades, you can pour some warm water with mild detergent into the cup, then attach motor unit and run one blending cycle. Repeat until the blades are clean.
- After cleaning let the all the parts air dry.
SPECIFICATION
Main features
- 6 stainless steel blades
- Level indicator with scale
- Anti-slip rubber ridge
- BPA free
- Protections: overheat, overcurrent, overload
Technical data
- Speed: 17000 rpm
- Cup capacity: 450 ml
- Used materials:
- Motor unit housing: ABS
- Blades: stainless steel
- Cup: borosilicate glass
- Charging port: micro USB
- Charging time: approx. 4 h
- Battery: 2x 2000 mAh
- Power: 100 W
- Power supply: 5 V / 1 A
- Set includes: cap, micro USB cable
Physical parameters
- Dimensions: Ø 82×226 mm
- Weight: 580 g
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or its literature,
indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>