teesa TSA3228 Slow Juicer Owner’s Manual
- June 3, 2024
- teesa
Table of Contents
Slow juicer
TSA3228
Owner’s manual
TSA3228 Slow Juicer
Motor unit
Power switch
Pulp ejector
Juice ejector
Anti-spill cap
Bowl| Strainer
Auger
Food chute lid
Pusher
Cleaning brush
Juice container
Pulp container
---|---
Thank you for purchasing this TEESA appliance. Please read this operation instruction carefully before use, and keep it for future use. Producer does not take responsibility for damages caused by inappropriate handling and use of the product.
SAFETY INSTRUCTIONS
In order to reduce the injuries or damages, follow basic safety precautions applied when using any electrical device, including the following:
-
Read this instruction manual carefully, even if you are familiar with the appliance. Keep the manual for future reference.
-
Before connecting the device to power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
-
The appliance must be plugged into an earthed electrical socket. If you have to use an electrical extension lead, it must be earthed.
-
This appliance MUST NOT be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility, as it may lead to damage of the device.
-
Place the device on flat, stable surface. Do not use this appliance on a tilted or unstable table.
-
Clean this device in accordance to instructions listed in “Cleaning and Maintenance” section.
-
Clean the parts and attachments that come in contact with food before first use!
-
ALWAYS turn off the device and disconnect it from the mains supply:
• if it’s not operating correctly
• if there’s an uncommon voice when using
• before disassembling the device
• before cleaning
• when not in use -
Check the strainer every time you want to use the appliance.
-
When you disconnect the power cord of the device, grasp and pull the plug, not the cord/cable.
-
Keep the device out of the reach of children. Do not leave children unsupervised with the product.
-
This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device. Children should not perform cleaning and servicing of the device unsupervised.
-
Fixed power cable may only be replaced in an authorized service point.
-
Keep the device and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
-
Do not place the appliance in water or any liquid; nor handle/use it with wet or moist hands.
-
Do not use the product for purposes different from displayed in this operating manual.
-
Do not leave the appliance unattended when it’s working.
-
Producer of this product is not responsible for damages caused by inappropriate handle and use of the device.
-
ALWAYS disconnect the product form the mains supply when it is not in use.
-
DO NOT use this device if the cord or the plug is damaged, or the appliance is broken.
-
Do not attempt to repair this appliance yourself. Only authorized and qualified personnel may repair this device. Never disassemble the motor body of the device.
-
Do not use unauthorized accessories.
-
Appliance for indoor and household use only. The device is constructed to process normal household quantities. Not for commercial use.
-
Do not move the appliance while it is operating.
-
This appliance is suitable exclusively for food preparation. Do not place anything but food in the appliance.
-
Don’t place hot ingredients inside the appliance. Hot ingredients should be cooled down prior to processing in the appliance (max. ingredient temperature is 50°C).
-
Always securely clamp in place all parts before the motor is turned on. Do not disassemble while the device is operating.
-
Do not touch moving parts. Make sure the motor stops completely before disassembling.
-
All parts apart from motor unit are suitable for dishwasher cleaning.
-
If the device get stuck, try reverse gear or turn off and unplug the appliance before removing the ingredients blocking the stuck part of the device.
-
Always wait until the moving parts stop running after switching off, and then unplug the appliance before opening, disassembling or removing the parts.
-
Do not use for more than 20 minutes at a time, allow motor to cool before reusing.
Note: the device has an overheat protection, which means that when the motor’s temperature increases significantly, the juicer will stop operation for safety reasons. Let
it cool down before using it again. -
Never touch any moving parts when the device is connected to power supply. Never stick or use your fingers or any object (for example a spatula) into to the device while the appliance is running – use only pusher provided.
-
Do not put the already squeezed fruit pulp into the device for re-juicing.
-
Do not process fruit dunked in wine, honey, sugar etc.
-
This product is strictly prohibited for non-load operation or overload operation.
-
IMPORTANT: In order to ensure children‘s safety, please keep all packaging (plastic bags, boxes, etc.) out of their reach. Caution! Do not allow small children to play with the foil as there is a danger of suffocation!
FEATURES
- Reduces oxidation
- Preserves organic nutrients and vitamins
- High extraction rate
- BPA free
BEFORE FIRST USE
Wash the parts that will have contact with food before first use. Rinse thoroughly with warm water and allow to air dry. Never submerge the device motor unit in water or any other liquid.
ASSEMBLY
-
Assemble the bowl to the motor unit.
• Make sure to properly assemble the bowl.
• Pay attention to the markings on the motor unit and the bowl: align the spot on the bowl with the open padlock on the base, twist clockwise to lock. -
Assemble the strainer to the bowl.
• Align the bottom bulge of the strainer with the bottom grooves of the bowl, until it is fixed well. -
Place the auger in the center of the bowl.
• Place the auger at the center hole of the bowl and rotate it until it can not move. -
Place the food chute lid onto the bowl.
• Pay attention to the markings on the bowl and the food chute lid: align the spot on the lid with the open padlock on the bowl, twist clockwise to lock.
NOTE: If the device has not been correctly assembled or the food chute lid is not completely locked onto the bowl, the device will NOT start.
USING THE SLOW JUICER
-
Once all parts have been properly assembled, connect the device to power supply socket.
-
Place the juice and pulp containers under the ejectors.
-
Food preparation:
• Cut the ingredients before processing. Tough and fibrous products like celery should be chopped fine, across the fibers.
• When extracting ingredients like carrots or beets, extract with a combination of other fruits and vegetables with more water content to increase the juice yield.
• Do not process frozen fruits. Thaw them completely before juicing!
• Large quantities of ingredients put into the feeding tube at once can cause the juicer to stop.
• Before placing food in the food chute, make sure all products have been thoroughly washed/peeled if necessary.
• Make sure to remove any hard seeds or pits, such as cherry or plum pits, as it will not process in the juicer and can damage the auger.
• Be careful when processing fine seed fruits – the seeds may easily jam the strainer.
• Insert the ingredients one piece at a time.
• Do not put dried or hard ingredients like whole grains, beans, fruits with hard seeds or ice into the juicer. These may damage the juicer parts.
• Do not use ingredients containing excessive amounts of vegetable oil or animal fat, as the device may get damaged.
• Do not reinsert the extracted pulp into the juicer. -
The slow juicer has 3 settings:
• ON – starts the motor for juicing
• 0 – stops operation
• R – auger moves in the opposite direction. (Note: press and hold the switch to R position for reverse rotations) -
When placing any food in the slow juicer, the auger will automatically pull in the food, and begin juicing immediately. DO NOT push, force, or over stuff the unit. The pusher provided with the slow juicer is only to use when food obstructs the inside of the food chute.
-
It is best to insert all food at a slow pace, allowing all pulp to be extracted from the fruit or vegetable completely.
-
If the ingredients become jammed in the screw and the food chute does not open, turn the power switch to OFF (0). Then press and hold the R (reverse) button until the ingredients become dislodged. Repeat REVERSE – OFF – FORWARD as often as needed to achieve the desired result.
-
Under the bowl, there is a silicone pad that prevents juice from exiting through the pulp ejector. When using the slow juicer, make sure the silicone pad is firmly in place.
When cleaning the bowl, make sure to slide the pad out and run water through the pulp ejector to remove excess food.
Reminder: turn off the slow juicer when juicing is complete. Do not run the
device without any food inside the unit as this could damage the motor.
The slow juicer has a self pre-cleaning process when switching between
different types of juices. To clean, simply place juice container under the
juice ejector and pour water though the food chute while the unit is on. This
will rinse out most of the remaining residue from your last juicing. When the
water from the slow juicer begins to run clear, that is an indication the unit
is clean and ready to make a new juice recipe.
NOTE: This process is not an alternative to a complete cleaning of each
disassembled part.
DO NOT put into juicer:
Hard seeds| Peach, nectarines, apricot, plum, mango, etc.| Remove hard seeds
from the ingredients before juicing.
---|---|---
Hard or inedible skins| Pineapple, melon, mango, orange, etc.| Peel the skins
from the ingredients before juicing.
Frozen fruits or ice| Frozen strawberry, blueberry, raspberry, etc.|
Completely thaw frozen fruits before juicing. Do not use ice.
Vegetable/animal oil| Sesame seed, butter, margarine, etc.| Do not extract
ingredients containing vegetable or animal oil. This can reduce performance
and even damage the juicer.
Very hard| Coconut, sugarcane, whole grains, etc.| Do not extract ingredients
with no water content. These can damage the device.
TIPS
- Carefully drop food into the food chute. The slow juicer pusher provided is only for use if any food obstructs the inside of the food chute. Do not over stuff, shove or force the food down.
- Cut food into pieces prior to processing (max. 3x2x5). Tough and fibrous products like celery should be chopped fine, across the fibers.
- For best results, insert foods slowly to allow pulp to be extracted, do not over stuff or rush the juicing process.
- Do not put any frozen fruit, vegetables or ice into the unit.
- Combine leafy greens with a variety of fruit for the best results.
- Close the anti spill cap and extract two or more different products. The juice will mix up in the juice bowl, so you could open the cap and get an already mixed juice straight to your glass.
- If the ingredients are not fresh, the juice yield will be lower due to the decreased water content in the ingredients.
- Some ingredients are not appropriate for juicing, like bananas.
- During the operation, the juicer may occasionally squeak when juicing some ingredients (i.e. carrots). This is normal.
- It is advised to consume the juice as soon as possible after processing. Stored juice will be subject to oxidation.
- IMPORTANT: juice clarity varies depending on toughness of processed ingredient. The softer the ingredient the lower the clarity.
DISASSEMBLING
- Rotate the food chute lid counterclockwise when and pull it upward.
- Pull out the auger and the strainer from juicing bowl.
- Rotate juicing bowl counterclockwise and take it out.
CLEANING AND MAINTENANCE
-
Switch the device off, and disconnect from power supply.
-
Disassemble the upper unit in the following order:
• food chute
• auger
• strainer
• bowl -
Use the included slow juicer cleaning brush, thoroughly clean each of the disassembled parts using warm water, with slight addition of light detergent. Remember to move the silicone pad under the bowl to clean the remaining debris in the pulp ejector.
Note:
- Don’t use an abrasive cloth or abrasive liquids.
- Do not rinse the slow juicer base or submerge the motor base in water.
- Dry all slow juicer attachments before reusing.
- Never use strong household cleaners, ammonia or abrasives while cleaning the device.
- Cleaning the device immediately after each use will also help to reduce stains on the bowl or upper parts.
- In case of tougher stains or when the parts have discolored by food (carrots, oranges etc.), soak them in mild soapy water and rub them gently with kitchen towel dipped in cooking oil and then clean in the usual way.
- Allow the parts to dry thoroughly before reassembling the device.
TROUBLE SHOOTING
| PROBLEM | SOLUTION |
|---|---|
| Device does not work | •Check power cord and power source. |
•Check that all parts have been assembled correctly.
Machine jams, clogs or stops operating| •Check food chute is clear and is not
blocked. Make sure the food pieces are small enough.
•Check that hard seeds have been removed before juicing and are not stuck in
the machine
•Turn machine off, and switch to reverse for 3 seconds.
•Disassemble upper section and clear remaining pulp.
Squeaking noise /
bowl is shaking when juicing| •Processing hard ingredients (like carrots).
This is normal.
•Working with no food inserted. Do not run the juicer without any food!
Leaking from underneath the bowl| •Be sure the silicone pad is tightly in
place.
•The device has been overloaded (do not put too much ingredients into the bowl
at once).
Too much pulp coming out| Cut food into smaller pieces, especially fibrous
foods to avoid fibers scrapping around the auger. Insert food at a slower pace
and allow all food pulp to eject the unit before adding more.
Cannot open juicing bowl cover| •Please confirm whether there is too much
residue in the juicing bowl. If yes, please press the„ON” button to remove the
residue.
•Please confirm whether there are hard objects as core stuck in the juicing
bowl. If yes, press the„Reverse” button to return the hard objects to the
feeding tube.
SPECIFICATION
Main features
- Keeps the nutritions, avoids oxidations
- Strainer with small holes
- Dishwasher safe parts
- Easy to clean
- Easy to assemble
- Anti-drip juice outlet
- Anti-slip feet
Used materials
- Auger: Tritan
- Housing: Stainless steel
- Strainer: Stainless steel + PCTG
Technical data
- Speed: 40-65 rpm
- Motor: DC
- Extraction rate: < 80%
- Construction: Single auger
- Reverse rotations: Yes
- Design: Vertical
- Noise level: < 65 dB
- Continuous working time: ≤ 20 minutes
- Pulp container capacity: 1000 ml
- Juice container capacity: 800 ml
- Protections: Against overheat and incorrect assembly
- BPA free: Yes
- Power: 200 W
- Power supply: 220-240 V; 50/60 Hz
Set includes
- Slow juicer, 2 containers, Brush, Pusher
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or its literature,
indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolińska 1,
08-400 Miętne.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>