ARDESTO MGL-1790R Electric Meat Grinder Instruction Manual

ARDESTO MGL-1790R Electric Meat Grinder

IMPORTANT SAFEGUARDS

Please read carefully and keep the instruction well. This appliance is equipped with a thermostat system. This system will automatically cut off the power supply to the appliance in case of overheating.
If you appliance suddenly stops running:

1. Pull the mains plug out of the socket.
2. Press the switch button to turn off the appliance.
3. Let the appliance cool down for 60 minutes.
4. Put the mains plug in the socket.
5. Switch the appliance on again.

Please contact your dealer of an authorized service center if the thermostat system is activated too often. If you plug in, the indicator light will be on.
CAUTION: In order to avoid a hazardous situation, this appliance must never be connected to a time switch.

IMPORTANT

1. Read these instructions for use carefully and look at the illustrations before using the appliance.
2. Before use, tight the fixing ring by spanner, make sure the ring cannot be detached by 4 Nm.
3. Keep these instructions for future reference
4. Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance.
5. Never use any accessories of parts from other manufacture. Your guarantee will become invalid if such accessories or parts have been used.
6. Do not use the appliance if the mains cord, the plug or oth- er parts are damaged.
7. If the power cord of this appliance is damaged, it must always be replaced by manufacture or a service center au thorized, in order to avoid hazardous situations.
8. horoughly clean the parts that will come into contact with food before you use the appliance for the first time. Unplug the appliance immediately after use.
9. Never use your finger or an objection to push ingredients down the feed tube while the appliance is running. Only the pusher is to be used for this purpose.
10. Keep the appliance out of the reach of children.
11. Never let the appliance run unattended.
12. Switch the appliance off before detaching and install any accessory
13. Wait until moving parts have stopped running before you remove the parts of the appliance.
14. Never immerse the motor unit in the water or any other liquid, nor rinse it under the tap. Use only a moist cloth to clean the motor unit.
15. Do not attempt to grind bones, nuts or other hard items.
16. Never reach into the cutter housing. Always use the pusher.
17. Mincers are fed with sinewless, boneless and fatles beef that has been cut into pieces approximately 20 mm x 20 mm x60 mm. Pushers are pressed with a force of 5N against the meat. Do not use the appliance for more than 5 minutes consecutively. Leave the appliance to cool for 10 minutes before using again.
18. Accessories shall include instructions for their safe use.
19. It shall warn of potential injury from misuse.
20. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance bya person responsible
21. for their safety.
22. Children should be supervised to ensure that they do not play with the appliance.
23. If the appliance is locked, please press Reversal button (REV). The meat locked in cutter housing is untrodden, so the appliance can renew its usual condition.
24. Disposal of appliances and batteries.
25. Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. Ihis symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilizing old devices, you are making an important contribution to protecting our environment.
26. This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are aged from 8 years and above and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
27. This appliance is intended to be used in household and similar applications such as:
    • staff kitchen areas in shops, offices and other working environments;
    • farm houses;
    • by clients in hotels, motels and other residential type environments;
    • bed and breakfast type environments.

DESCRIPTION

EQUIPMENT

• Disassembled meat grinder 1 pc.
• Nozzle for making sausage – 1 pc.
• Nozzle for making «kebbe» – 1 pc.
• Tomato juicer 1 pc.
• Instruction manual -1 pc.
• Warranty card (added to the instruction manual)- 1 pc.

INSTRUCTION FOR USE

ASSEMBLING

• Press the fasten button, hold the head and insert it into the inlet (when inserting please  pay attention the head must be slanted as per arrow indicated on the top, see fig.1), then move the head anticlockwise so that the head being fastened tightly (fig.2).
• Place the snake into the head, long end first, and turn to feed the screw slightly until it is set into the motor housing (fig.3).
• Place the cutting blade onto the snake shaft with the blade facing the front as llustrated (fig.4). If it is not fitted properly, meat will not be grinded.
• Place the desired cutting plate next to the cutting blade, fitting protrusions in the slot (fIg.5
• Support or press the center of the cutting plate with one finger then screw the fixing ring tight with another hand (fig.6). Do not Over tighten.
• Place the hopper plate on the head and fix it into position.
• Locate the unit on a firm place.
• The air passage at the bottom and the side of the motor housing should be kept free and not blocked

MINCERR

1. Insert the worm shaft into the cutter housing, the plastic end first. Place the cutter unit onto the worm shaft (the cutting edges should be at the front). Place the medium grinding disc or coarse grinding disc (depending on the consistency you prefer) onto the worm shaft (make sure the notch of the grinding disc fit onto the 20 projections of the mincer head). Turn the screw ring in the direction of the arrow on the cutter housing until it is properly fastened.
2. Attach the cutter housing to the motor unit.
3. Place the tray on the upright part of the cutter housing.
4. Now the appliance is ready for mincing. Cut the meat into 10cm-long, 2cm-thick strips. Remove bones, pieces of gristle and sinews as much as possible. Never use frozen meat! Put the meat in the tray. Use the pusher to gently push the meat into the cutter hosing. For steak tartare, mince the meat with the medium grinding disc twice

MAKING KEBBE

1. Insert the worm shaft into the cutter housing, the plastic end first (fig.8). Place the cone in the cutter housing. Place the former on the cutter housing and screw the ring on the cutter housing (fig.9).
2. Attach the cutter housing to the motor unit.
3. Place the tray on the upright part of the cutter housing.
4. Now the appliance is ready for making kebbe (fig.10).
   Feed the prepared kebbe mixture through the kebbe maker. Cut the continuous hollow  cylinder into the desired lengths and user as required.
   Kebbe is a traditional Middle Eastern dish made primarily of lamp and bulgur wheat which are minced together to form a paste the mixture is extruded through the kebbe maker and cut into short lengths. The tubes can then be stuffed with a minced meat mixture, the ends pinched together and then deep fried.

MAKING SAUSAGES

1. Mince the meat. Insert the worm shaft into the cutter housing, the plastic end first (fig.11).
   Place the separator in the cutter housing. Place the sausage horn on the cutter housing and screw the ring on the cutter housing. Make sure the notches of the separator fit onto the projections of the mincer head.

2. Attach the cutter housing to the motor unit.

3. Place the tray on the upright part of the cutter housing.

4. Now the appliance is ready for making sausages. Put the ingredients in the tray. Use the pusher to gently push the meat into the cutter housing.
   Put the sausage skin in lukewarm water for 10 minutes. Then slide the wet skin onto the sausage horn. Push the (seasoned) minced meat into the cutter housing. If the skin gets stuck onto the sausage horn, wet it with some water.

TOMATO JUICER

1. Place the plastic screw locking ring into the sleeve (fig.1).
2. Place the gauze into the sleeve next to the plastic screw locking ring (fig.2).
3. Put the fixing ring through the sleeve and make it at the end of the sleeve (fig.3).
4. Place the snake into the head, long end first, and turn to feed the snake slightly until it is set into the motor housing (fig.4).
5. Insert the shaft of the snake into the central axis of the screw (fig.5).
6. Put the whole sleeve along with the fixing ring through the screw, then move the fixing ring clockwise so that it being fastened tightly. tightly (fig.6).
7. Put the plastic juice tray through the sleeve and make it on the suitable position (fig.7).
8. Insert the plastic screw into the hole of the sleeve, then move it clockwise until it is properly fastened. Then place the plastic cover onto the sleeve (fig.8). Now the appliance is ready for juicing.

HOW TO CLEAN YOUR APPLIANCES

Meat left behind in the cutter housing may be removed from the inside of the appliance by passing a slice of bread through the cutter housing.

1. Before you clean the appliance, switch the appliance off and remove the plug from the socket (fig.12).
2. Press the release button and turn the whole cutter housing in the direction of the arrow. Remove the pusher and the tray (fig.13).
3. Unscrew the screw ring and remove all parts of the cutter housing. Do not clean the parts in the dishwasher!
4. Wash all parts that have come into contact with meat in hot soapy water. Clean them immediately after use.
5. Rinse them with clear hot water and dry them immediately.
6. We advise you to lubricate the cutter unit and the grinding discs with some vegetable oil.

DISPOSAL OF APPLIANCES AND BATTERIES

Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices, you are making an important contribution to protecting our environment.

WARRANTY CARD

Dear Buyer! Congratulations on your purchase of the ARDESTO brand appliance, which was designed and manufactured in accordance with the highest quality standards, and we thank you for choosing this particular instrument.
We ask you to keep the coupon during the warranty period. When purchasing a product, require a full warranty card.

1. Warranty service is carried out only if there is a correctly and clearly filled original warranty card, which indicates: product model, date of sale, serial number, warranty service period, and the seller’s seal.
2. The service life of household appliances is 5 years.
3. The product is intended for consumer use. When using the product in commercial activities, the seller/ manufacturer does not bear warranty obligations, after-sales service is performed on a paid basis.
4. Warranty repair is carried out within the period specified in the warranty card for the product in an authorized service center on the conditions and terms determined by applicable law
5. The product is withdrawn from the warranty in case of violation by the consumer of the operating rules set forth in the instruction manual.
6. The product is removed from warranty service in the following cases:
   • misuse and non-consumer use
   • mechanical damage;
   • damage caused by the ingress of foreign objects, substances, liquids, insects;
   • damage caused by natural disasters (rain, wind, lightning, etc.), fire, domestic factors (excessive humidity, dust, aggressive environment, etc.)
   • damage caused by non-compliance of power and cable network parameters with state standards and other similar factors;
   • when operating equipment in the power supply network with a missing single ground loop;
   • in case of violation of seals installed on the product;
   • lack of serial number of the device, or inability to identity it.
7. The warranty does not cover consumables and accessories, as well as filters, shelves, drawers, stands and other containers for storing products.
8. The warranty period is 12 months from the date of sale.
   *Tear-off maintenance tickets are provided by an authorized service center.

The completeness of the product is checked. I have read the terms of the warranty service, no complaints.
Customer Signature

Warranty card

• Product information
• Product
• Model
• Serial number
• Seller Information
• Trade organization name
• The address
• Date of sale
• Seller stamp

References

• Компания ERC: Сервис-центр(СЕРВІСНИЙ ЦЕНТР)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>