Solmetex DS-PSK-002 DryShield Pediatric Starter Kit User Guide

June 16, 2024
Solmetex

Solmetex logo Quick Start Guide
Isolation. Protection.
Workflow. Simplified.

INSTALLATION

Dedicated
Replace the existing HVE with the DS1, attaching it to the tubing. Use the Y Connector if there is only one HVE.

| Solmetex DS PSK 002 DryShield Pediatric Starter Kit - Dedicated
2
---|---
Twist off existing HVE (with attached coupler) from tubing.| Attach DS1 to existing tubing by twisting into place.

Portable
Insert the DS1 into the end of the Portable Operatory Kit, and plug the kit into your HVE tip.

Solmetex DS PSK 002 DryShield Pediatric Starter Kit - Portable
1|
---|---
Attach one end of portable kit to HVE.| Attach DS1 to other end of portable kit.

PATIENT INTRODUCTION

Please prep the patient by telling them:

  1. DryShield was designed for safety and comfort.
  2. This shield will protect your tongue and cheek.
  3. Rest your jaw on the bite block.
  4. Relax, breathe through your nose, and we’ll be done in no time.

PRE-INSERTION

| Solmetex DS PSK 002 DryShield Pediatric Starter Kit - Pre insertion
2
---|---
Spray air and water inside the mouthpiece to lubricate.| Slide mouthpiece onto the DS1, using a rocking motion until it locks in place.
Solmetex DS PSK 002 DryShield Pediatric Starter Kit - Pre insertion
3| Solmetex DS PSK 002
DryShield Pediatric Starter Kit - Pre insertion 4
Fold tail in towards the center of the mouthpiece.| Then fold outside edges of the mouthpiece towards the center of the mouthpiece.

MOUTHPIECE INSERTION

| Solmetex DS PSK 002 DryShield Pediatric Starter Kit - Mouthpiece
2
---|---
Slowly insert, lining up the bite block’s anterior edge to distal of the canine.
(For kids, midline of the primary lateral.)| Release the mouthpiece and let fall, using finger pressure to adapt it to the inner cheek,
retromolar pads, palate and floor of the mouth.
Solmetex DS PSK 002 DryShield Pediatric Starter Kit - Mouthpiece
3|
Position the bite block distal to the maxillary canine, then allow patient to rest their jaw on it.| Make sure the mouthpiece is fully adapted to the mouth, and reposition lips as needed. Slide the
bite block distally if you need more vertical opening.

Sterilization Guide

| Solmetex DS PSK 002 DryShield Pediatric Starter Kit - Figure
2
---|---
Detach bite block from mouthpiece.| Scrub both with small brush (e.g. toothbrush) using soap and water, including inside the neck and slit of mouthpiece. Invert under water and check for removal of all debris.
Solmetex DS PSK 002 DryShield Pediatric Starter Kit - Figure
3|
Place mouthpiece and bite block in ultrasonic solution for 15 minutes.| Rinse off ultrasonic solution under running water and lay onto cloth to dry
| Solmetex DS PSK 002 DryShield Pediatric Starter Kit - Figure
6
Place bite block and mouthpiece into autoclave bag and seal.| Steam autoclave for min 121 C (250 F) for at least 30 min, followed by a 30-min drying cycle.

As a rule of thumb, when the mouthpiece begins to take on a perceptible tint, it is an indicator that it may be time for disposal and replenishment

WWW.DRYSHIELD.COM
877-207-1551Solmetex
logoWWW.SOLMETEX.COM

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals