VOLLRATH 1001 Meat Grinder Chamber Instruction Manual
- August 13, 2024
- VOLLRATH
Table of Contents
VOLLRATH 1001 Meat Grinder Chamber
Specifications
- Brand: Vollrath
- Model: Meat Grinder
- Item No.: 2350053-1
- Assembly Required: Yes
- Power Source: Electric
- Manufacturer: The Vollrath Company, L.L.C.
Product Usage Instructions
Installation Instructions
To ensure safe installation and operation, carefully follow the steps
below:
- Inspect the shaft washer for wear and replace if necessary.
- Avoid water and liquids from entering the unit to prevent electrical shock.
- Handle sharp blades with caution to prevent cuts and injuries.
Assembly Procedures
- Turn off the meat grinder and unplug it.
- Clean and dry all parts thoroughly.
- Assemble the blade shaft into the worm gear as shown in Figure 1.
- Slide the shaft washer onto the worm gear shaft and seat it against the worm gear assembly.
- Slide the worm gear assembly and shaft washer into the grinder chamber until fully seated.
- Place the knife blade onto the blade shaft ensuring it is seated completely over the square.
- Attach the grinder plate onto the blade shaft so that the cutout slides over the locating pin.
- Thread the coupling cover onto the grinder chamber and tighten securely.
Disassembly Procedures
- Turn off the meat grinder and unplug it.
- Unscrew and remove the coupling cover from the grinder chamber.
- Remove the grinder plate from the blade shaft.
- Carefully remove the knife blade from the blade shaft.
- Remove the worm gear assembly from the grinder chamber.
- Clean and dry all parts thoroughly.
FAQ
-
Q: Can I use an extension cord with this unit?
A: No, do not use an extension cord with this unit as it may cause hazards. Always connect directly to a power outlet. -
Q: How do I know if the shaft washer needs replacement?
A: Inspect the shaft washer for wear as shown in Figure 2. If there are signs of damage or wear, replace it before use. -
Q: Is it safe to wash the components with water?
A: No, avoid washing with water or liquids to prevent electrical shock. Clean with a dry cloth or brush instead.
Installation Instructions
Meat Grinder Chamber and Components Assembly and Disassembly
To ensure safe installation and operation, read the following statements and understand their meaning. Please read carefully.
WARNING
Warning is used to indicate the presence of a hazard that can cause severe
personal injury, death, or substantial property damage if the warning is
ignored.
Safety Precaution
| **** | WARNING |
|---|
Electrical Shock Hazard.
Keep water and other liquids from entering the inside of the unit. Liquid inside the unit could cause an electrical shock.
Do not spray water or cleaning products. Liquid could contact the electrical
components and cause a short circuit or an electrical shock. Do not use unit
if power cord is damaged or has been modified. Do not use an extension cord
with this unit.
**| WARNING
---|---
Sharp Blade Hazard.**
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal should operate equipment or preform maintenance.
ASSEMBLY PROCEDURES
- Turn the meat grinder off and unplug from its power source.
- Thoroughly clean and dry all parts.
- If necessary assemble the blade shaft (B) into the worm gear (A). See Figure 1.
- Inspect the shaft washer (A) for wear. See Figure 2. Replace if necessary.
- Slide the shaft washer (A) onto the worm gear shaft (B).
- Slide the shaft washer (A) so that it is seated against the worm gear assembly (B) as shown. See Figure 3.
- Slide the worm gear assembly (B) and the shaft washer (A) into the grinder chamber (C). Slide the worm gear shaft (D) in until it is seated fully.
- Slide the knife blade (B) so that the flat ground edges (A) face to the outside as shown, onto the blade shaft (C). See Figure 4.
- Slide the knife blade (B) onto the blade shaft (C) so that it seats completely over the square (D). See Figure 5.
- Place the grinder plate (D) onto the blade shaft (A) so that the cutout (C) slides over the locating pin (B). See Figure 6.
- If a sausage filler is to be used, place it between the coupling cover (A) and the grinder chamber (B). See Figure 7.
- Thread the coupling cover (A) onto the grinder chamber (B) and tighten securely.
DISASSembly Procedures
- Turn the meat grinder off and unplug from its power source.
- Unscrew and remove the coupling cover (A) from the grinder chamber (B). See Figure 7.
- Remove the grinder plate (D) from the blade shaft (A). See Figure 6.
- Carefully remove the knife blade (B) from the blade shaft (C). See Figure 5.
- Remove the worm gear assembly (B) from the grinder chamber (C). See Figure 3.
- Thoroughly clean and dry all parts.
www.vollrathco.com
The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201
U.S.A.
Main Tel: 800.628.0830 Fax: 800.752.5620
Technical Services: 800.628.0832 Service Fax: 920.459.5462
Canada Service: 800.695.8560
© 2010 The Vollrath Company, L.L.C.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>