VOLLRATH 38075 Tray Slide Plate Rest Cutting Board Installation Guide
- August 14, 2024
- VOLLRATH
Table of Contents
VOLLRATH 38075 Tray Slide Plate Rest Cutting Board
Specifications
- Product: Tray Slide, Plate Rest, Cutting Board (Removable, Non-Folding)
- Model No.: 2350036-1
- Revision: 01/14
Product Usage Instructions
Tray Support Hardware Installation
- Remove the plugs (A) from the holes (B) in the unit.
Plate Rest and Bracket Installation
- Turn the plate rest (C) so the weld nuts (B) are exposed.
- Secure the brackets (D) to the weld studs (B) using the nylock nuts (A).
Tray Slide and Bracket Installation
- Turn the tray slide (C) so the weld nuts (B) are exposed.
- Install the screw (A), lockwasher (C), and flat washer (D).
- Secure the brackets (D) to the weld studs (B) using the nylock nuts (A).
Cutting Board Top, Bracket, and Cutting Board Installation
- Turn the cutting board top (C) so the weld nuts (B) are exposed.
- Secure the brackets (D) to the weld studs (B) using the nylock nuts (A).
- Secure the cutting board locating nuts (D) to the cutting board top (B) using the screws (C).
Plate Rest, Tray Slide, and Cutting Board Installation and Removal
- To install, slide the keyholes (A) on the brackets (B) over the screws (C).
- To remove, slide the keyholes (A) on the bracket (B) up and off the screws (C).
- Place the cutting board (A) onto the cutting board top (B) using the nuts (D) to center and locate.
FAQ
-
Q: How do I clean the cutting board?
A: The cutting board can be removed for thorough cleaning. Simply follow the removal instructions and clean with a mild detergent and warm water. -
Q: Can I fold the tray slides?
A: No, the tray slides are non-folding and should not be bent or folded as it may damage the product.
Installation Instructions
Tray Slide, Plate Rest, Cutting Board (Removable, Non-Folding)
These instructions cover the installation of the of removable non-folding tray slides, plate rests and cutting boards.
Tray SupporT Hardware Installation
-
Remove the plugs (A) from the holes (B) in the unit. See Figure 1.
Figure 1. Plug Removal -
Install the screw (A), lockwasher (C) and flat washer (D). See Figure 1. Repeat on the other holes as necessary.
Plate Rest and Bracket Installation
-
Turn the plate rest (C) so the weld nuts (B) are exposed. See Figure 3.
-
Secure the brackets (D) to the weld studs (B) using the nylock nuts (A) as shown.
Tray Slide and Bracket Installation
- Turn the tray slide (C) so the weld nuts (B) are exposed. See Figure 4.
- Secure the brackets (D) to the weld studs (B) using the nylock nuts (A) as shown.
Cutting Board Top, Bracket and Cutting Board Installation
- Turn the cutting board top (C) so the weld nuts (B) are exposed. See Figure 5.
- Secure the brackets (D) to the weld studs (B) using the nylock nuts (A) as shown.
- Secure the cutting board locating nuts (D) to the cutting board top (B) using the screws (C) as shown. See Figure 6.
- Place the cutting board (A) onto the cutting board top (B) using the nuts (D) to center and locate. The cutting board can be removed for thorough cleaning as necessary.
Plate Rest, Tray Slide and Cutting Board Installation and Removal
- To install the plate rest, tray slide or cutting board: Slide the key holes (A) on the brackets (B) over the screws (C). See figure 7.
- Slide the keyhole (A) down on the screws (C).
- To remove the plate rest, tray slide or cutting board: Slide the key holes (A) on the bracket (B) up and off the screws (C).
www.vollrathco.com
The Vollrath Company, L.L.C.
1236 North 18th Street Sheboygan,
WI 53081-3201 U.S.A.
Main Tel: 800.628.0830
Fax: 800.752.5620
Technical Services: 800.628.0832
Service Fax: 920.459.5462
Canada Service: 800.695.8560
© 2010 The Vollrath Company, L.L.C.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>