VOLLRATH 15008 Section Vegetable Wedge Installation Guide

VOLLRATH 15008 Section Vegetable Wedge

Product Specifications

• Brand: Vollrath
• Model: Tabletop and Wall Mount
• Blade Type: Sharp cutting blade assembly
• Material: Stainless steel
• Usage: Food processing

Product Usage Instructions

1. Blade Preparation:

   • Wash new blades with warm, soapy water to remove protective oil film.
   • Handle blades with caution to avoid cuts and injuries.

2. Assembly:

3. Tabletop Models:
   Remove the pusher head assembly by sliding it off the rod guides.

4. Wall Mount Models:
   Remove the pusher head assembly by following the specific instructions provided.

5. Blade Replacement:

6. Loosen thumbscrew and carefully remove the old blade assembly.

7. Install the new cutting blade assembly securely.

8. Lubrication:

   • After each use, lubricate the guide bar with mineral oil or Petrol-Gel.
   • Avoid using cooking oil to prevent equipment damage.

FAQ

• How often should I replace the blades?
  Blades should be replaced when they become dull or damaged, or as recommended by the manufacturer.

• Can I wash the blade assembly in a dishwasher?
  It is recommended to wash the blades by hand with warm, soapy water to maintain their sharpness and quality.

• What type of lubricant should I use for the guide bar?
  Use mineral oil or Petrol-Gel for lubricating the guide bar. Avoid using cooking oil as it may damage the equipment.

WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal should operate equipment or preform maintenance.

Blade Replacement

Wash new blades with warm, soapy water and rinse thoroughly to remove the thin protective oil film. Keep the sharp edge away from you when handling blades.

1. Remove the pusher head assembly:
   Tabletop models: Slide the pusher head off the rod guides.
   Wall mount models: Remove the locking pin (J). Lift handle and slide the pusher head off the guide rods. Place pin back into the hole on the handle assembly to prevent loss.

   • A Guide Rods. Guides and align the pusher head onto the blade set.
   • B Handle. Used to lower and raise the pusher head block
   • C Guides. Used for smooth and consistent operation of pusher head on the guide rods
   • D Pusher Head Assembly. Made up of the pusher head block (and “T” handle for tabletop models).
   • E Bumpers. Cushions the stop of the pusher head.
   • F Thumbscrew. Used to secure the pusher head block or the blade assembly.
   • G Pusher Head Bock. Pushes the food product through the blade set. Specifically sized to match the corresponding blade assembly.
   • H Blade Assembly. Houses the blades. Specifically sized to match the corresponding pusher head block
   • I Base Assembly. Holds the guide rods and blade assembly.
   • J Locking Pin. Secures the pusher head to the handle.

2. Raise the bumpers approximately 2” (5.0 cm).

3. Loosen thumbscrew and carefully remove the blade assembly. Remove the cutting blade assembly by pressing upwards on the bottom of the side of the blade holder, where the thumbscrew is located. Discard the old blade assembly.

4. Install the new cutting blade assembly by inserting the tab on the blade holder into the groove in the base, then lowering the blade holder into the seated and flush position in the base. Tighten the thumbscrew.

5. Slide bumpers down guide rods to contact base assembly. Position pusher head assembly onto the guide rods, slowly lower pusher head assembly, and check pusher head block to blade alignment.

6. Lubricate the guide bar with mineral oil or Petrol-Gel after each use. Do not use cooking oil as it will become sticky and may permanently damage the equipment.

ABOUT COMPANY

• The Vollrath Company, L.L.C.
  • 1236 North 18th Street
  • Sheboygan, WI 53081-3201 U.S.A.
  • Main Tel: 800.624.2051 or 920.457.4851
  • Main Fax: 800.752.5620 or 920.459.6573
  • Customer Service: 800.628.0830
  • Canada Customer Service : 800.695.8560
• Technical Services
  • techservicereps@vollrathco.com
  • Induction Products: 800.825.6036
  • Countertop Warming Products: 800.354.1970
  • All Other Products: 800.628.0832
• www.vollrath.com

References

• Commercial Foodservice & Kitchen Equipment | Vollrath Foodservice

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>