SATCO NUVO Ash Wood Melrose Mini Pendant Instruction Manual

SATCO NUVO Ash Wood Melrose Mini Pendant

Specifications

• Item Numbers: 62-816, 62-817, 62-818, 62-819, 62-820, 62-826, 62-827, 62-828, 62-829, 62-830
• No special tools are required for installation
• Proper wiring is essential for safe operation

FAQs

• Q: Do I need special tools for installing this fixture?
  • A: No, special tools are not required for installation. Follow the provided instructions carefully.
• Q: Can a swag-type fixture be installed on a ceiling with a radiant heating system?
  • A: No, a swag-type fixture should not be installed on a ceiling with a radiant-type heating system.
• Q: What should I do if I am unclear about installation steps?
  • A: If you are unsure about how to proceed with the installation, consult a qualified electrician for assistance.

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

• You don’t need special tools to install this fixture. Be sure to follow the steps in the order given.
• Under no circumstances should a fixture be hung on house electrical wires, nor should a swag-type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully.
• If you are unclear as to how to proceed, consult a qualified electrician.
• NOTE: Proper wiring is essential for the safe operation of this fixture.

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all parts are included as shown in the figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.

INSTALLATION

IMPORTANT: Do not attach the fixture directly to the outlet box.

• STEP 1: Secure the mounting bar to the outlet box with the outlet box screws. Thread the nipple onto the mounting bar.
• STEP 2: Cut the wire to approximate hanging height. NOTE: Leave extra wire to make wire connections, see Figure. Feed the wire through the finial, canopy, and nipple. Re-attach the plastic strain relief to the wire.

GROUNDING INSTRUCTIONS

• STEP 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
• STEP 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
  GROUP A:

Connect to Black House Wire

| GROUP B:

Connect to White House Wire

---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER

• NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from the wire end.)
• STEP 3: Take your fixture wire(s) from group A and place it evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
• STEP 4: Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
• STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
• STEP 6: Connect the fixture wire from group B to the white wire from the outlet box the same man can be seen outside the wire connectors.

FINAL ASSEMBLY

• STEP 1: After the wires are connected, tuck them carefully inside the outlet box. Raise canopy and secure with finial.
  • The line art shown may not exactly match the fixture enclosed. However, the installations do apply to this fixture.
• STEP 2: Adjust the height with a small plastic set screw at the top of the fixture housing. With a small flat-bladed screwdriver loosen the plastic set screw and push the extra wire into the fixture housing until the height is set, then tighten it to hold it in place.

CLEANING

• To clean, wipe the fixture with a soft cloth. Clean glass with a mild soap.
• Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

ORDERING PARTS

• Keep this sheet for future reference, and in case you need to order replacement parts.
• Be sure to use exact wording from illustration when ordering parts

Optional Satco Pendant

Optional Satco Pendant Track Adapter (tp231, tp232, tp233)

• STEP 1: Remove the top cover by loosening the screws of the Adapter.
• STEP 2: Loosen the plastic screw at the bottom of the Adapter.
• STEP 3: Insert the cord from the light fixture into the hole of the fitting and attach the strain relief to the SVT wires from the light fixture. Be sure to leave an extra wire between the Adapter and fixture for final adjustments.
• STEP 4: Secure the wire by tightening the plastic screw on the Adapter.
• STEP 5: Connect wiring, and follow Grounding Instructions.
• STEP 6: Re-install the top cover by tightening the screws of the Adapter.
• STEP 7: To install on track hold down the housing of the Adapter while twisting it into place. Make sure the grounded side of the Adapter (2-prong side) turns to the side of the track with the polarity line on the track.

ITEM NO: 62-816, 62-817, 62-818, 62-819, 62-820, 62-826, 62-827, 62-828, 62-829, 62-830

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>