hama 00176607 LED Wall Light for Indoors and Outdoors Instruction Manual
- June 12, 2024
- Hama
Table of Contents
- 00176607 LED Wall Light for Indoors and Outdoors
- Explanation of symbols used on the product label
- Explanation of warning symbols and notes
- Package contents
- Safety instructions
- Product characteristics
- Installation
- Integrating devices into the Hama Smart Solution app
- Setting options
- Extended usage options with scenarios
- Care and maintenance
- Warranty disclaimer
- Recycling information
- RF exposure information
- Declaration of conformity
- Technical data
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
00176606
00176607
WiFi Wall Light
Operating Instructions
00176607 LED Wall Light for Indoors and Outdoors
Link to App
https://link.hama.com/app/smart-
homeThank you for choosing a Hama
product.
Take your time and read the following instructions and information completely.
Please keep these instructions in a safe place for future reference. If you
sell the device, please pass these operating instructions on to the new owner.
Explanation of symbols used on the product label
| Electrical device of safety class II.
Protection against electric shock thanks to reinforced or double insulation of
live parts.
---|---
| The product must only be used with alternating current.
| Non-dimmable.
The lamp is not suitable for use with a conventional dimmer.
| The article may only be connected by a qualified electrician who complies
with national regulations and those of the local energy supply company, and
who has sufficient knowledge regarding installation locations, fire protection
and electrical installation work.
Replaceable control gear by a professional
Explanation of warning symbols and notes
Risk of electric shock
This symbol indicates a risk of electric shock from touching product parts
carrying hazardous voltage.
Warning
This symbol is used to indicate safety instructions or to draw your attention
to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
Package contents
- 1 Wall light
- 2 Insulation tubes
- Mounting hardware
- Quick-start guide
Safety instructions
- This product is intended for private, noncommercial use only.
- Use the product only for the intended purpose.
- Do not drop the product and do not expose it to any major shocks.
- Do not operate the product outside the power limits specified in the technical data.
- Do not modify the product in any way. Doing so voids the warranty.
- Children must not play with the device. Cleaning and user maintenance must not be carried out by children without supervision.
- As with all electrical products, this device should be kept out of the reach of children.
- Dispose of packaging material immediately in accordance with the locally applicable regulations.
- The product must only be operated on a supply network as described on the type plate.
- Before mounting, check that the wall you have chosen is suitable for the weight to be mounted. Also make sure that there are no electric, water, gas or other lines running through the wall at the mounting site.
- Electrical cables must never become trapped or twisted between the product and the surface.
- If the product is attached to a metal surface, it must be connected to an earth lead or the installation’s potential equalising cable.
- Only use the article under moderate climatic conditions.
- Do not use the product in areas in which electronic products are not permitted.
- Do not use the product in a damp environment and avoid splashing water.
- Do not bend or crush the cable.
- Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
- Do not continue to operate the device if it is visibly damaged
- No bare spots must be visible after connection
Warning
- Please note that lights (even LEDs) can generate heat and may become hot. Always let the light cool down for a few minutes before touching it.
- The device can only be operated on a 230 V 50 Hz AC voltage network. Work on the 230 V network must only be carried out by an electrician certified in your country. The applicable accident prevention regulations must be adhered to.
- To avoid an electric shock from the device, please disconnect the mains voltage (switch off the automatic circuit breaker). Failure to comply with the installation instructions can cause fires or other hazards.
Risk of electric shock
Do not open the product and do not operate it if it is damaged, if smoke, a
strange smell or loud noises are coming from it. Immediately contact your
dealer or our service department (see item “Service and Support”).
Note
The light source of this light is not replaceable; when the light source has
reached the end of its life, you need to replace the entire light. Warning
Never look straight into the light source and do not aim its beam of light
straight into the eyes of other people or animals. This could damage
your/their eyes.
Note
This light contains a light source of energy efficiency class “F”.
Product characteristics
- The SMART LED light can be connected to your wireless home network via WiFi and serves as illumination in indoor rooms or outdoor areas.
- It can be controlled via a mobile device (mobile phone/tablet) as well as via the Amazon Alexa / Echo and Google Home Voice services.
- A selection of voice commands is available, such as:
Switch on / off
“Alexa / OK Google, switch the light on / off.”
Dim to X %
“Alex / OK Google, reduce the light to X %”.
Dim by X %
“Alexa / OK Google, increase the light X %.”
Colour temperature selection
“Alex / OK Google, switch the light to warm white.” (white, daylight, etc.)
Installation
- Switch off the relevant fuse (fuse box) for the room in which you wish to install the light.
- Check that the wires are de-energised using a suitable measuring device (e.g. multimeter).
- Pull the housing upwards and off.
- Loosen the grub screws on the side using the Allen key provided.
- Never look straight into the light source and do not aim its beam of light straight into the eyes of other people or animals. This could damage your/their eyes.
- Please note that lights (even LEDs) can generate heat and may become hot. Always let the light cool down for a few minutes before touching it.
- Pull the wires through the hole (with rubber insulation) on the mounting plate and attach the insulation tubes. The tubes must cover the connecting cable inside the light up to the terminals. Shorten any connecting wires that are too long.
- Insulate the cables as specified on the terminals (10 mm).
- No earth wire can be connected to the lamp, nor should it be.
- Attach the mounting plate to the wall using the screws and dowels supplied.
- Connect the wires to the light terminals. Please ensure that the seal is correctly inserted.
- Place the wall light on the mounting plate and tighten the grub screws on the side.
- Now push the housing back onto the wall light.
Integrating devices into the Hama Smart Solution app
- Switch the fuse back on.
- Connect the product to your wall switch.
- The product starts to flash quickly. If it does not, switch it ON and OFF 3 times using the light switch.
- Now open the Hama Smart Solution app and sign in.
- Press the “+ in the top right-hand corner to add a new device.
- Choose Lights from the list.
- Next enter your WiFi password and confirm with OK.
- Now confirm that the product is flashing quickly and click Next.
- Your product is now connected.
- Once the connection is successful, the product stops flashing quickly and the app confirms that the connection was successful. You can now assign it a different name if you wish.
- Click Finish to end the process.
- You can now control your product.
Setting options
The following settings can be made in the app:
1 | White | Open the Light settings tab. |
---|---|---|
2 | Scenario | Open the Colour scenarios tab. Customised light settings can be |
stored here and selected at the press of a button.
3| Colour slider| Set the preferred colour temperature here.
4| Brightness slider| Set the preferred brightness here.
5| Countdown| Once the set time has elapsed, the light is automatically
switched on or off.
6| On/Off button| Switch the light on or off with the press of a button.
7| Timeline| Create time-controlled programmes here.
For extended usage options, scenarios can be created in the app. (See Section 9 and App Guide)
Extended usage options with scenarios
Scenarios and automated sequences, which can be created in the app in the
“Smart scenarios” section, can be used to create many combination and usage
options for these products, depending on the Smart Home products you have
installed.
Programming is always via the app (see Section 4 of the App Guide) and will be
offered / suggested to you on an individual basis.
Standard usage option Extended usage option
Care and maintenance
Note
Disconnect the product from the mains before cleaning and during prolonged
periods of non-use.
- Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
- Ensure that no water is able to enter the product.
Warranty disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.
Recycling information
Note on environmental protection:
Following the implementation of European Directives 2012/19/EU and
2006/66/EU into the national legal systems, the following applies: Electrical
and electronic devices as well as batteries must not be disposed of with
household waste. Consumers are obliged by law to return electrical and
electronic devices as well as batteries to the designated public collection
points or to the point of sale at the end of their service lives. Detailed
information on this topic is defined in the national laws of the respective
country. This presence of the above symbol on the product, operating
instructions or package indicates that the product is subject to these
regulations. By recycling, reusing the materials or other forms of utilising
old devices/ batteries, you are making an important contribution to protecting
our environment.
RF exposure information
This device complies with the EU requirements for limiting the exposure of the general public to electromagnetic fields by means of health protection. The device complies with RF specifications provided it is used 20 cm away from the body.
Declaration of conformity
Hama GmbH & Co KG hereby declares that the radio equipment type [00176606, 00176607] is in compliance with Directive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following Internet address: www.hama.com -> 00176606, 00176607 -> Downloads.
Technical data
WiFi Wall Light|
---|---
Luminous flux| 360 lm
Light output| 3.6 W
Connected load| 6 W
Light colour| 2700% – 6500%
(warm white to cold
white)
Input voltage| 2700% – 6500%
Frequency band/ frequency bands| 2.4 GHz
Maximum radiofrequency power transmitted| < 100 mW
Hama GmbH & Co KG
86652 Monheim / Germany
Service & Support
www.hama.com
+49 9091 502-0
“Google and Google Play are trademarks of Google LLC.”
All listed brands are trademarks of the corresponding companies.
Errors and omissions excepted, and subject to technical changes.
Our general terms of delivery and payment are applied.
00176606
07/03.23
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>