DUKWIN YG22B Fingerprint Lock Watch Winder Owner’s Manual

: August 14, 2024
: DUKWIN

Table of Contents

DUKWIN YG22B Fingerprint Lock Watch Winder Owner’s Manual
Introduction
1. Feature
2. Power
3. Pause Switch
4. Watch Cuff
5. LED Light Stripe
6. Fingerprint Lock
7. Controls
8. Winding Modes
9. Contact
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DUKWIN YG22B Fingerprint Lock Watch Winder Owner’s Manual

Introduction

Congratulations on your purchase of this watch winder.
Please review this quick start guide so that your automatic watch will benefit fully from the features that have been engineered into this product.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Appliance is only to be used with the power supply unit provided with the appliance.

Images and model for YG22B-FR series

1. Feature

2. Power

The models for YG22B-034-FP watch winders comes with a power adapter (AC/DC5 .0V-volt. 1A output)
Power supply: AC Adapter(US/UK/AU/EU)

The models for YG22B-064-FP watch winders comes with a power adapter (AC/DC5 .0V-volt. 2A output)
Power supply: AC Adapter(US/UK/AU/EU)

The models for YG22B-094-FP watch winders comes with a power adapter (AC/DC5 .0V-volt. 3A output)
Power supply: AC Adapter(US/UK/AU/EU)

Suitable for various 5.0V I.OA12.OA13.OA USB specififications plugs

NOTES:
Never use any unauthorized power adapter or not up to specification power adapter.

3. Pause Switch

When you turn on the “pause switch” and open the front cover, all drums will immediately stop rotating. When you turn off the “pause switch” and open the front cover, all drums continue rotating.

4. Watch Cuff

This unique patent design is best match for different size of watch bracelet/wrist.
It can fit Max 55mm watch dial, watch thickness is up to 20mm, and the bracelet/ wrist diameter limited from 35 – 62mm.

How to use the cuff
Step 1: Remove the cuff from the winder drum by pulling on the two tabs. Step 2: Close the strap or bracelet of your watch.
Step 3: Compress the cuff, and slide your watch over the cuff, watch dial facing outward.

NOTES:
If your watch strap is too short, you can push out the detachable parts at the bottom, and then follow the steps to put the watch inside. Push the cuff into the drum until it locks into place, an audible click will be heard.

5. LED Light Stripe

There are two LED light stripe are embedded in the upper and lower parts of the watch box. The LED light has 3 grades to assists users to read the watch status. It will be activated when the power switch on, either the front cover open or program have been manipulated. In order to save power, the back-light will automatically turn off when there is no input detected for about 30 seconds, LED light stays on unless you turn it off.

6. Fingerprint Lock

Note:

Factory Mode: Any fingerprint can be unlocked Status of successful fingerprint enter: The blue light will be on for 2 seconds.
Status of unsuccessful fingerprint enter: The red light will flash for 3 times.
The fingerprint sensor can set up to 20 fingerprint users(2 administrator and 18 user accounts)
The first two fingerprints entered are administrators by default.

6.1 Fingerprint Account Setting
1. First administrator fingerprint account setting:
Press and hold the fingerprint sensor panel for 7 seconds, release your finger when the blue indicator flashes the first time, then you can see the blue indicator flashes another two times, till the pink indicator flashes once, indicating that it will enter the fingerprint registration state: Using the fingerprint you defined as an administrator, input 6 valid presses continuously on the panel, the blue light will flash once every time you press it, until the system collects your fingerprints 6 times, the blue light will be on for 2 seconds, indicating that the first fingerprint entry is successful, and exit the fingerprint entry mode.

Note:
During fingerprint entry, if the red light flashes, it is invalid entry, and it is necessary to continuously enter valid fingerprints for 6 times with the blue light flashing 6 times.

2. Second administrator fingerprint account setting:
Do the same as above l) mention. When the pink indicator flashes once, indicating that you need to enter once your first administrator fingerprint to confirm, then put your second administrator finger on the panel input 6 valid presses continuously. The blue light will flash once every time you press it, until the system collects your fingerprints 6 times, the blue light will be on for 2 seconds, indicating that the second administrator fingerprint entry is successful.that the second administrator fingerprint entry is successful.

3. The 3-20 fingerprint accounts setting:
The fingerprint entry steps are the same as the method for entering the second administrator fingerprint account.

Note:
The mode of using the admin key is not required administrator fingerprint confirmation during any fingerprint entry process.

6.2 Using Admin Key Setting Mode
Insert the key, short press the key button once, then the blue light will flash 3 times, indicating that you can enter your fingerprint: Using the fingerprint you defined as an administrator, input 6 valid presses continuously on the panel, the blue light will flash once every time you press it, until the system collects your fingerprints 6 times, the blue light will be on for 2 seconds, indicating that the first fingerprint entry is successful.

Note:
The mode of using the admin key is not required administrator fingerprint confirmation during any fingerprint entry process.

6.3 Fingerprint Accounts Remove/Reset

There are two ways to remove fingerprints: Using Fingerprint Verification OR Using Admin Key.

1. Using Fingerprint Verification
Press and hold the sensor with any finger, do not release your finger, the blue light will flash 3 times during the period, do not release your finger, continue to press, then the red light will flash 3 times, prompting you to enter the administrator fingerprint twice, each valid press will be accompanied by the pink indicator light indicates that the verification is successful. After releasing the finger, the blue light stays on for 2 seconds, indicating that all fingerprints have been cleared and the factory mode is restored.

2. Using Admin Key
Insert the key, press and hold the key button for about 5 seconds, the blue light is always on, when the pink light is displayed, it means that all fingerprints have been cleared, and the factory mode is restored.

7. Controls

With the adapter connected, turn on the “Power Switch”. The display will be lit and all options will flicker back and forth, then you can set the programs by Touchscreen Control Panel or the Remote Control.

7.1 Remote Control

7.2 Remote Control

Hold down the “ALL” button for 5 seconds to display Initialization. Press the “Switch” button to perform initialization. The ticked icon will appear in the upper left corner of the middle four choices, representing the “ALL” Mode. When you choose any other button, initialization mode will go off and returns to the original mode of your operation.
Initialization parameter: TPD=850; Direction=bidirectional; Switch =Stop; Motor Selection=01 group; ALL=ALL selected. Working Hours=24 hours.
When you change any of the parameters: Switch – TPD – Direction -Lights, the initialization mode will exit and the initialization prompt will go off.

2. All Mode
Tap the “ALL” button 4 times until the top left corner of each of the four options shows a ticked icon, or Press the “motor selection” and “Run” buttons at the same time for 5 seconds, and then tap the “Run” button. All watches will be set to the current mode. . If you change the parameters of “Switch -TPD – Direction”, all watches will be change to the current parameters.

3. Custom Mode

Motor Options:
If the current mode is ALL, just tap the “ALL” button again, the “Motor Options” will appear, and you can set the mode of each motor individually.

4. New Watch Mode
New Watch Mode: Press and hold the “TPD” button until the ” —-” diagram is displayed.
Note: During the new watch mode, any operation will cause the new watch mode to exit and return to the previous settings.

8. Winding Modes

1. The TPD value is between 300 – 2300. By turn up and turn down to change TPD value, over 300 TPD returns to 2300 TPD cycle.
2. TPD Calculation Method: 10 turns per cycle

· 24-hour mode operating cycle (minutes) =1440/ (TPD/10 turns);
· 12-hour mode operating cycle (minutes) =1440/ (TPD/10 turns) /2;
· 8-hour mode operating cycle (minutes) =1440/ (TPD/10 turns) /3;
e.g: TPD set to 650, clockwise, 24 hours mode. Then the running period (minutes) =22.2, that is, each cycle is 22.2 minutes.
Cycle execution: the time required for the motor to rotate clockwise 10 times

the motor stop time = 22.2 minutes. In the 12 (8 hours) working mode, the cycle runs for 12 (8 hours) hours and then stops; stops for 12 (16 hours) hours, and then restarts the cycle.

Note:

There is no magic number of rotations that will wind your watch. Things such as how active you are, how many complications your watch has, how frequently you use the chronograph function, how frequently you wear your watch, the watch make, how long it has been since it was last serviced and a host of other variables will impact what your watch requires to stay wound.

And a watch winder won’t wind a watch that is fully stopped. So, you need to manually wind the timepiece to get it running first. You will have to make this determination by trying the various settings.