DUKWIN DK20 Enchanted Watch Winder User Manual

DUKWIN DK20 Enchanted Watch Winder

Specifications

• Model: Enchanted Series Watch Winder (DK20)
• Patented design : 009053200-0001
• Power Supply Options:
  • 5.0V 2.0A AC Adapter (US/UK/AU/EU)
  • 5.0V 3.0A AC Adapter (US/UK/AU/EU)
  • 5.0V 4.0A AC Adapter (US/UK/AU/EU)

INTRODUCTION

Congratulations on your purchase of this watch winder. Please review this quick start guide so that your automatic watch will benefit fully from the features that have been engineered into this product. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience\ and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision. The appliance is only to be used with the power supply unit provided with the appliance.

Power

The models for DK20-008 fingerprint watch winders come with a power adapter (AC/DC5.0V-volt. 2A output)

Power supply: 5.0V 2.0A AC Adapter (US/UK/AU/EU)

The models for DK20-009 fingerprint watch winders comes with a power adapter (AC/DC5.0V-volt. 3A output)
Power suoolv: 5.0V 3.0A AC Adanter(US/UK/AU/FU)

Suitable for various 5.0V 2.0/3.0A USB specifications plugs The models for DK20-012 fingerprint watch winders comes with a power adapter (AC/DC5.0V-volt. 4A output)
Power supply : 5.0V 4.0A AC Adapter (US/UK/AU/EU)|

NOTE

1. External power connection is required to use fingerprint lock, external power input is DC5V, please do not connect reverse polarity.
2. Never use any unauthorized power adapter or up-to-specification power adapter.

The back of the watch winder

PAUSE SWITCH
When you turn on the ‘pause switch” and open the front cover, all drums will immediately stop rotating. When you turn off the “pause switch” and open the front cover, all drums continue rotating. Your watch will always stop at the 12 o’clock position when the cycle is complete.

Controls

With the adapter connected, turn on the ‘Power Switch”. The display will be lit and all options will flicker back and forth, then you can set the programs by Touchscreen Control Panel or the Remote Control.

LCD Touchscreen Control Panel

Custom Mode

Motor Options
If the LCD displays 4 ticked icons on the top left corner, just tap the ‘ALL’ button once, the ‘Rotor Option” will appear, then you can set the program of each rotor individually.

Initialization Mode

1. Hold down the ‘ALL” button for 5 seconds to display Initialization. Press the ‘Run” button to perform initialization. The ticked icon will appear in the upper left corner of the middle four choices, representing the “ALL” Mode. When you choose any other button, the initialization mode will go off and return to the original mode of your operation.
2. Initialization parameter: TPD=850: Direction= bidirectional; Switch = Stop:| Motor Selection=01 group: ALL=ALL selected. Working Hours 24 hours.
3. When you change any of the parameters: Switch – TPD – Direction – Lights, the initialization mode will exit and the initialization prompt will go off.

ALL Mode
ALL Mode means one action controls all the rotors, If all your watches have the same parameters, you can use this mode, if not, you can use ‘Custom Mode” to program each rotor.
How to use “ALL MODE”

Tap the “ALL” button 4 times, OR press the left first and second buttons at the same time for 3 seconds, you will see 4 ticked icon appear on the top left corner of the middle of the four options. Then tap the “Run” button. That is the “ALL Mode’. If you change the parameters of “Switch – TPD – Direction”, all rotors will be set to one program.

New Watch Mode New Watch Mode: Press and hold the “TDP” button until the ” --* diagram is displayed

New Watch Mode Working Chart

Direction Setting| Working Time| Rest Time
Clockwise| 4 hours| 8 hours
Counterclockwise| 4 hours| 8 hours

Bi-directional

| Clockwise for 2 hours and Counterclockwise for 2 hours|

8 hours

Finally return to the previously set mode

4 Winding Mode

1. The TPD value is between 300 – 2300. By turn up and turn down to change the TPD value, over 300 TPD returns to 2300 TPD cycle.
2. TPD Calculation Method: 10 turns per cycle 24-hour mode operating cycle (minutes) =1440/ (TPD/10 turns) :
3. 12-hour mode operating cycle (minutes) =1440/ (TPD/10 turns) /2;
4. 8-hour mode operating cycle (minutes) =1440/ (TPD/10 turns) / 3;
5. eg: TPD set to 650, clockwise, 24-hour mode. Then the running period (minutes)
6. =22.2, that is, each cycle is 22.2 minutes.
7. Cycle execution: the time required for the motor to rotate clockwise 10 times + the motor stop time = 22.2 minutes. In the 12 (8 hours) working mode, the cycle runs for 12 (8 hours) hours and then stops; stops for 12 (16 hours) hours, and then restarts the cycle.

Note
There is no magic number of rotations that will wind your watch. Things such as how active you are, how many complications your watch has, how frequently you use the chronograph function, how frequently you wear your watch, the watch make, how long it has\ been since it was last serviced and a host of other variables will impact what your watch requires to stay wound. And a watch winder won’t wind a watch that is fully stopped. So, you need to manually wind the timepiece to get it running first. You will have to make this determination by trying the various settings.

Remote Control

Fingerprint Lock

• A Admin Key
•  Fingerprint panel: Put your finger in here to identify.
• C LED Status: There are 3 LED status, blue light, red light, and pink light.

Note

• Factory Mode: Any fingerprint can be unlocked
• Status of successful fingerprint entry: The blue light will be on for 2 seconds.
• Status of unsuccessful fingerprint entry: The red light will flash 3 times.
• The fingerprint sensor can set up to 20 fingerprint users (2 administrator and 18 user accounts)
• The first two fingerprints entered are administrators by default.
• Please do not set duplicate fingerprint account.

Fingerprint Accounts Setting

• There are two fingerprint setting modes: Using Fingerprint Verification OR Using the Admin Key.

Fingerprint Verification Setting Mode

1. First administrator fingerprint account setting: Press and hold the fingerprint sensor panel for 7 seconds, do not release your finger, after the blue indicator flashes 3 times, you can release your finger, and then the pink indicator flashes once, indicating that it will enter the fingerprint registration state: Using the fingerprint you defined as an administrator, input 6 valid presses continuously on the panel, the blue light will flash once every time you press it, until the system collects your fingerprints 6 times, the blue light will be on for 2 seconds, indicating that the first fingerprint entry is successful, and exit the fingerprint entry mode.
   Note:
   During fingerprint entry, if the red light flashes, it is an invalid entry, and it is necessary to continuously enter valid fingerprints 6 times with the blue light flashing 6 times.

2. Second administrator fingerprint account setting:
   Press and hold the fingerprint sensor panel for 7 seconds, do not release your finger, after the blue indicator flashes 3 times, you can release your finger, and then the pink indicator flashes once, indicating that you should enter once your first administrator fingerprint to confirm, then put your second administrator finger on the panel input 6 valid presses continuously. The blue light will flash once every time you press it, until the system collects your fingerprints 6 times, the blue light will be on for 2 seconds, indicating that the second administrator fingerprint entry is successful.

3. The 3-20 fingerprint accounts setting:
   The fingerprint entry steps are the same as the method for entering the second administrator fingerprint account.

Using Admin Key Setting Mode
Insert the key, short press the key button once, then the blue light will flash 3 times, indicating that you can enter your fingerprint: Using the fingerprint you defined as an administrator, input 6 valid presses continuously on the panel, the blue light will flash once every time you press it, until the system collects your fingerprints 6 times, the blue light will be on for 2 seconds indicating that the first fingerprint entry is successful.

Note:
The mode of using the admin key is not require administrator fingerprint confirmation during any fingerprint entry process.
Fingerprint Accounts Remove/Reset
The mode of using the admin key does not require an administrator fingerprint confirmation during any fingerprint entry process.

1. Using Fingerprint Verification
   Press and hold the sensor with any finger, do not release your finger, the blue light will flash 3 times during the period, do not release your finger, continue to press, then the red light will flash 3 times, prompting you to enter the administrator fingerprint twice, each valid press will be accompanied by the pink indicator light indicates that the verification is successful. After releasing the finger, the blue light stays on for 2 seconds, indicating that all fingerprints have been cleared and the factory mode is restored.

2. Using Admin Key
   Insert the key, and press and hold the key button for about 5 seconds, the blue light is always on, and when the pink light is displayed, it means that all fingerprints have been cleared, and the factory mode is restored. (If you have any questions, check out our YouTube video link)

Watch Cuff

This unique patent design is best match for different sizes of watch bracelets/wrists. It can fit Max 55mm watch dial, the watch thickness is up to 20mm, and the bracelet/wrist diameter is limited from 35 – 62mml

LED Light Stripe

• Step 1: Remove the cuff from the winder drum by pulling on the two tabs.
• Step 2 : Close the strap or bracelet of your watch.
• Step 3 : Compress the cuff, and slide your watch over the cuff, the watch dial facing outward.

NOTES:

• If your watch strap is too short, you can push out the detachable parts at
• the bottom, and then follow the steps to put the watch inside. Push the cuff into the drum until it locks into place, an audible click will be heard.

LED Light Stripe and Ambient Light
The LED light has 3 grades to assist users in reading the watch status. It will be activated when the power switch is on, either the front cover open or the program has been manipulated. In order to save power, the backlight will automatically turn off when there is no input detected for about 30 seconds, the LED light stays on unless you turn it off.

The grade of the light strip, a total of 3 grades

RGB Lights Symbol

How to use the cuff

There are 3 grades of LED light

Ambient Light

1. Entering and exiting the state of the ambient light: The ambient light will automatically turn on when the machine is on, and the symbol of the ambient light will not be displayed. Press and hold the
2. light button for 3 seconds to turn off the color light, and then long press the light control to enter the color light mode, which can be adjusted when the ambient light symbol is displayed. No operation for 10 seconds or other operation will exit the ambient light control. Auto Mode: Automatic cycle for 48 colors.
3. Adjust the lights of a certain color: double-click the light control

FAQ

• Q : How do I reset the watch winder to factory settings?
• A: To reset to factory settings, follow the steps outlined inthe Initialization Mode section of the user manual.
• Q: Can I use a different power adapter with the watch winder?
• A : It is recommended to use the specified power adapter to ensure proper functioning and avoid damage to the device.

Contact

• if we don’t answer your question here, then email us below: For our
• website: support@dukwinwatchwinders.com
• After-sales for other selling platform: dukwinwatchwinder@gmail.com
  Whatsapp: +1 6315455745

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>