CAPITAL Fire Places User Manual
- August 6, 2024
- CAPITAL
Table of Contents
CAPITAL Fire Places
Product Information
Specifications
- Power Supply: 220-240V~
- Power Cable Length: 3 meters
- Fuse: 3 Amp
- LED Spotlight Wattage: 3W each
- Material Thickness Compatibility: 5mm to 20mm
Product Usage Instructions
Precautions
Before starting any work with the lighting kit, ensure it is disconnected from
the power supply. Verify that all components are in working order.
Installation Steps
- Prepare the fireplace/beam by creating the necessary holes as per the requirements specified.
- Connect the components following the provided wiring diagram.
- Mount the LED spotlights and toggle switch securely in place.
- Test the lighting kit to ensure proper functionality before finalizing installation.
FAQs
Q: Can I replace the spotlights in the kit?
A: Yes, replacement spotlights are available from your fireplace
retailer.
Q: What is the recommended distance from the stove and flue?
A: Ensure a 300mm distance from the top of the stove and a direct line of
sight to the flue for optimal performance.
BEFORE ANY WORK IS CARRIED OUT WITH THIS LIGHTING KIT ENSURE THAT IT IS NOT
CONNECTED TO THE POWER SUPPLY
PLEASE CHECK THAT ALL COMPONENTS ARE IN WORKING ORDER BEFORE PROCEEDING WITH
THE INSTALLATION
INTRODUCTION
- PLEASE LEAVE THESE INSTRUCTIONS WITH THE END USER.
- This kit is must be installed by a competent person. THIS IS NOT A DIY INSTALLATION.
- Installation must take place prior to the final fixing of the fireplace or Geocast beam as access to the rear will be necessary. We do not recommend retrofitting this light set into an existing fireplace as removal from the wall and precision drilling is needed. Please refer to your Fireplace dealer for further advice.
- The LED spotlight and driver unit can be replaced by the end user, taking care to isolate at the mains first. This can be done by removing the spotlight and carefully withdrawing the cable and driver through the hole for the lights.
- The toggle switch can become warm-to-touch and so it is recommended that the fire is turned off at least 20 minutes before turning off the lights. The switch can also be replaced if necessary, this is done by carefully easing it out from its seating complete with approximately 20cm of the two joining cables until the connector blocks can be safely disconnected. When reconnecting ensure the spade connectors on the switch housing are secure before reinstallation. Again, ensure the mains supply is disconnected first!
KIT CONTENTS
- One x 3 metre power cable with moulded plug, 3 Amp fuse.
- One x two-pole toggle switch 220-240V~
- One x 90cm + 20cm cable for connecting the switch to the driver units.
- Two x 3w LED spotlights with connected inline drivers.
- Replacement spotlights are available from your fireplace retailer
FIREPLACE / BEAM REQUIREMENTS
- Two 50mm diameter holes for the light fittings
- One 20mm diameter hole for the toggle switch
- Material thickness 5mm to 20mm maximum.
- Ensure a 300mm distance from the top of the stove and 300mm distance for direct line of sight to flue.
INSTALLATION
- Locate on which side of the fireplace lies the wall socket you plan to use. Ensure there is sufficient cable from the 20mm switch hole to run inside the header, down the inside leg and across to the wall socket. The plug cable supplied is 3 meters long and should be sufficient for most installations.
- Understand how you plan for the mains cable to exit from the installation and prepare any necessary cutting-in. Ensure the cable cannot be pinched once the fireplace is assembled.
- From the underside of the fireplace header, feed the connecting cables from the toggle switch through the 20mm diameter hole. Image 1 shows connectors and switch
- Connect one end of the switch cable to the mains cord and the other to 20cm part of the connection cable assembly.
- Push the switch up into the 20mm hole from below ensuring no cables are trapped
- Connect the two loose ends of the 90cm part of the connection cable to the two driver/spotlight assemblies.
- It is very important that the driver units are located as far away from the heat source as possible to avoid potential failure from overheating.
- If connected, disconnect the spotlights from the drivers. Press the springs on the rear of the spotlight unit together (image 2) and push up into position from underneath the header/beam.
- Reconnect each spotlight to its driver (image 3)
- Turn on the set temporarily to ensure it is working correctly before isolating the power supply and fitting the fireplace permanently, taking care to ensure no wires are trapped.
WARRANTY
- A warranty for replacement parts is provided for a period of one year from the date of purchase – labour costs, misuse and failure to follow these instructions are excluded.
Proof of purchase is required.
FEATURED
LED Light Set Wiring Diagram
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>