Furbo 3.5 360 Degree Cat Camera User Guide
- August 7, 2024
- Furbo
Table of Contents
Model: Furbo 3.5 Cat
Quick Start Guide
Furbo at a glance
- Eco-friendly natural bamboo lid
- Full HD camera with automatic night vision
- Mic
- Meowing sensor
- Treat tosser
- 360° rotating view
- Status indicator
- Speaker
- 3M Sticky pads
- Wand base
- Wand
- Feather
Placement guide
✔ 3-4ft (90-130cm) off the ground for maximum coverage and 360° rotation
✔ Within 15ft (4.5m) of Wi-Fi router
Setting up your Furbo
(1) (2)
(3) (4)
(5) (6)
(7)
Status indicator
SOLID – Starting up
BLINKING – Ready for setup
SOLID – Standby mode
SOLID – Live view mode
BLINKING – No Wi-Fi connection
Setting up your treat toss
Treat Recommendation
✔ Use dry and firm treats that are 0.3-0.5in (0.7-1.2cm)
✔ Use small treats for best treat-toss results
✔ Use treats that your cat likes
Need help?
Chat with our support agent if you have any questions or comments.
Live chat support
Scan QR code to contact us
Live chat FAQs
or email us at
support@furbo.com
Safety information
ALWAYS unplug your USB cord before attempting to clean your Furbo. Do NOT allow small children to operate Furbo. Do NOT place Furbo on the floor, as it increases risk of damage to Furbo. We recommend placing Furbo 90-130cm (3 feet to 4.25 feet) off the ground for best motion detection. Do NOT give toy to children or other animals. Do NOT use Furbo or toy if you see any damage to the camera, the USB cord, plug, or toy. Inspect before each use and if you see damage, please contact support@furbo.com. Immediately discard broken or chewed-on parts as they may be a choking hazard to your pet. Do NOT place your Furbo close to flammable materials. Do NOT keep your Furbo in hot temperatures (>120°F) or under prolonged exposure to direct sunlight. Do NOT submerge your Furbo in any kind of liquid. Do NOT try to disassemble any of Furbo’s parts for risk of electrical shock. Secure Furbo by placing it on an even and stable surface. Secure the power cord away from your pet to prevent it from being walked on, pinched, or chewed on.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
RF exposure warning
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for satisfying
RF exposure compliance.
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada’s licence-exempt RSSs. Operation
is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada
(IC) radio frequency exposure limits. The Wireless Device should be used in
such a manner such that the potential for human contact during normal
operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person’s body).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>