Furbo 3.5 Dog Camera User Guide
- August 5, 2024
- Furbo
Table of Contents
Furbo 3.5 Dog Camera
Product Information
Specifications
- Model: Furbo 3.5 Dog
- Power: 5V2A
Product Usage Instructions
- This device complies with FCC Part 15 rules and Industry Canada’s license-exempt RSSs. It must not cause harmful interference and should accept any interference received.
- Install and operate the device according to the provided instructions. Maintain a separation distance of at least 20 cm from all persons with the antenna(s) and avoid co-location with other antennas/transmitters to minimize interference.
- The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. Use the device in a way that minimizes human contact during normal operation.
- Under mobile exposure conditions, antennas should be greater than 20cm from a person’s body to comply with IC RF Exposure limits.
FAQ
- Q: What should I do if I experience interference with the device?
- A: Ensure that the device is not co-located with other transmitters or antennas, and follow the provided instructions for installation and operation to minimize interference.
- Q: How should I use the Furbo 3.5 Dog model?
- A: Make sure to power the device with a 5V2A power source. Follow the guidelines for RF exposure and ensure proper installation to maintain compliance with regulatory standards.
Need help?
- Chat with our support agent if you have any questions or comments.
- support@furbo.com
Placement guide
- 3-4 feet (90-130cm) off the ground
- Within 15 feet (4.5m) of Wifi router
- In an uncluttered space for maximum coverage and 360° rotation
Safety information
ALWAYS unplug your USB cord before attempting to clean your Furbo. Do NOT allow small children to operate Furbo. Do not place Furbo on the floor, as it increases the risk of damage to Furbo. We recommend placing Furbo 90-130cm (3 feet to 4.25 feet) off the ground for best motion detection. Do NOT use Furbo if you see any damage to the camera, the USB cord, or the plug. If you see damage, please contact support@furbo.com. Do NOT place your Furbo close to flammable materials. Do NOT keep your Furbo in hot temperatures (> 120°F) or under prolonged exposure to direct sunlight. Do NOT submerge your Furbo in any kind of liquid. Do NOT try to disassemble any of Furbo’s parts for risk of electrical shock. Immediately discard broken or chewed-on parts as they may be a choking hazard to your pet. Secure Furbo by placing it on an even and stable surface. Secure the power cord away from your pet to prevent it from being walked on, pinched, or chewed on.
Furbo at a glance
Setting up your Furbo
Status indicator
- SOLID – Starting up
- SOLID – Standby mode
- SOLID – Live view mode
- BLINKING – Ready for setup
- BLINKING – No Wi-Fi connection
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, according to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used under the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
RF exposure warning
This equipment must be installed and operated under provided instructions and
the antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provided with antenna installation
instructions and transmitter operating conditions for satisfying RF exposure
compliance.
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada
(IC) radio frequency exposure limits. The Wireless Device should be used in
such a manner that the potential for human contact during normal operation is
minimized.
This device has also been evaluated and shown compliant with the IC RF
Exposure limits under mobile exposure conditions. (antennas are greater than
20cm from a person’s body).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>