MOOER PRINE STONP S1 Intelligent Pedal Owner’s Manual
- August 6, 2024
- Mooer
Table of Contents
MOOER PRINE STONP S1 Intelligent Pedal
Precautions
PLEASE READ CAREFULLY BEFORE PROCEEDING
Power Supply
- Please use a power supply that meets UL, CSA, VED, or CCC standards.
- Please use the power supply that meets the manufacturer’s power requirement.
- Please unplug the power supply when the device is turned off or during a thunderstorm.
- Please do not expose the device which has battery power to heat or let it overheat.
- If battery leakage occurs, please do not touch the liquid with your skin or eye. If you do come in contact, please see a doctor.
- The battery included with the device may cause fire or chemical burns if handled improperly.
Location
To avoid deformation, discoloration, or other serious damage, do not expose
this unit to the following conditions:
- Direct sunlight or other heat sources
- Magnetic fields
- Excessively dusty or dirty locations
- Strong vibrations or shocks
- High humidity or moisture
Cleaning
Clean only with a soft, dry cloth. If necessary, slightly moisten the cloth.
Do not use abrasive cleansers, cleaning alcohol, paint thinners, wax,
solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Features
- Light-weight and portable design
- Integrated lithium battery, supports mobile power bank charging
- 126 guitar effects
- Comes with a tuner, metronome (x10), drum machine (x40), looper (80 seconds)
- USB/OTG function for direct recording on a mobile device
- Separate headphone output
- Two main outputs allow users to configure stereo connections
- Preset switching, drum machine, and looper can be easily controlled via footswitch
- Specialized App for mobile devices available
- MOOER Cloud can help users share and download tones easily
- The S1 is an intelligent platform and can be transformed into other effect modules by downloading and installing different firmware
- High-quality Bluetooth audio function
Layout
Instructions
Start
Power the S1 on, the I/O indicator will illuminate, please set up the connections according to the diagram.
Power On/Off and battery management
- Power On/Off: Toggle the power switch to On/Off to power the device On/Off.
- Battery management : When the device is ON, the battery indicator illuminates. When the battery is about to run out, the battery indicator will blink in RED. Please charge the device via the USB port.
Charging: When the power supply is plugged in, the charging indicator will illuminate. When the charging is complete, the indicator will turn GREEN.
Output volume level adjustment
Please use the MASTER control on the rear panel to adjust the master volume level.
Preset patch selection
Display: The LCD screen shows the currently selected preset patch.
- Preset bank selection : Press footswitch A + B for Bank Down, and press footswitch C + D for Bank Up.
- Preset patch selection: Press footswitch A, B, C or D to select a preset patch.
Drum machine/Looper
Press footswitches B + C to switch between preset control mode and looper mode. (Preset mode/drum machine + looper mode)
Looper
REC: Press footswitch A (the footswitch LED will blink slowly) to enter recording standby mode. The S1 will start recording when the first note is detected, the footswitch LED will start to blink quickly. The screenshows a recording loop.
PLAY: When the looper is in REC/STOP status, press footswitch A to activate playback, and the footswitch LED will stop blinking. The screen shows the recording loop.
DUB : In playback status, press footswitch A to start DUB (the footswitch
LED will blink quickly), and the screen will show the recording loop. Press
footswitch A to switch between playback and dub. Press footswitch A again to
stop the dub.
STOP : In REC/PLAY/DUB status, press footswitch B to stop. The footswitch
LED will stop blinking, and the loop in the display screen will stop rolling.
DELETE: Press and hold footswitch B to delete the recorded track (the LED of footswitch A & B will be Off). The display will show “LD”.
Drum machine
- Play/stop: Press footswitch D to start/stop the drum machine.
- TAP : Press footswitch C to enter TAP mode (the footswitch LED will blink, and the tempo of blinking syncs with the drum machine speed). Press footswitch C for more than 3 times to set the drum machine speed. The TAP mode will quit automatically after being idle for 3 seconds.
- Drum groove selection : Press and hold footswitch C for 2 seconds, footswitch C/D will start to blink. Press footswitch C or D to switch between drum grooves. The groove selection mode will quit automatically after being idle for 3 seconds, the footswitch LED will stop blinking. The display screen will show the number of the selected drum grooves.
Sync mode
Syncing can be activated/deactivated in the mobile app.
- Sync Off: When the sync mode is Off, the looper and drum machine will not be synchronized. The looper will start to record as soon as an input signal is detected, the drum machine will not start automatically.
- Sync On: When the sync mode is On, press footswitch A and the drum machine will play a 4-beat count-in according in the selected tempo. The looper will then start to record and the drum machine starts playing automatically. When the looper stops recording, the drum machine will stop simultaneously. When the looper restarts, the drum machine will restart as well. Speed and groove settings need to be configured properly before recording starts, as those settings cannot be changed during recording. (During recording, the drum machine can be muted, but it cannot be stopped.)
Tuner
In preset mode, press and hold any footswitch for 1 second to activate the tuner.
Bluetooth
Please open the Bluetooth menu of your mobile device, find S1 and confirm the connection. The S1 can then be used to play audio tracks from the mobile device via Bluetooth, and the Bluetooth indicator will illuminate.
USB-OTG
Prime S1 supports direct USB recording using a mobile phone/tablet via OTG
cable. Users can monitor the audio track via the OUTPUT or the headphone
output jack. In the MIXER menu of the Prime S1 App, users can adjust the OTG
recording output level, the audio playback output level, and the instrument
input level.
It is recommended to use the USB-C to USB-A cable.
Specifications
- Input : 1/4” mono audio jack, 2 MOhm
- Output: 1/4” mono audio jack, 100 Ohm
- Headphone output : 1/8” stereo audio jack, 32 Ohm
- USB cable: USB-C to USB-A cable
- Bluetooth version: 5.0
- Battery capacity: 2000 mAh
- Battery life: 4.5 hours
- Charging requirements: DC 5V/2A
- Wireless system : 2.4G
- Weight : 350 g
- Dimensions: 240 mm (D) x 70.2 mm (W) x 31.9 mm (H)
- Accessories: Quick Guide, USB cable
CONTACT
- www.mooeraudio.com
- SHENZHEN MOOER AUDIO CO. LTD
- 6F, Unit D, Jinghang Building, Liuxian 3rd Road,
- Bao’ a 71 District, Shenzhen, China. 518133
- Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>