MOOER Micro LOOPER-II Looper Pedal Owner’s Manual

**MOOER Micro LOOPER-II Looper Pedal Owner’s Manual

**

Precautions

PLEASEREADCAREFULLYBEFOREPROCEEDING

Power Supply
Please connect the designated AC adapter to an AC outlet of the correct voltage. Be sure to only use an AC adapter which supplies 9V DC, 120mA. Unplug the AC power adapter when not in use or during electrical storms.

Location
To avoid deformation, discoloration, or other serious damage, do not expose this unit to the following conditions:

• Direct sunlight or other heat sources
• Magnetic fields
• Excessively dusty or dirty locations
• Strong vibrations or shocks
• High humidity or moisture Radio Frequency Interference Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions.

Cleaning
Clean only with a soft, dry cloth. If necessary, slightly moisten the cloth.Do not use abrasive cleanser, cleaning alcohol, paint thinners, wax,solvents, cleaning fluids, or chemical-impregnated wiping cloths.

Feature

• Multi-saving-slot micro looper pedal
• Three saving banks, 16 slots for each
• Up to 10 minutes of recording time for each slot, 480 minutes in total
• Unlimited recording layers
• AUTO REC for starting recording automatically when the input signal is detected

TopPanel

1. Footswitch
   Press to start recording, playback, dub, and stop recording.

2. LED Button
   Press to turn On/Off the AUTO REO function. When you press the LED button, the LED will blink in RED for AUTO REC Off; the LED blinks in BLUE for AUTO REC On. Apart from the AUTO RECO function, the color of the LED will show the current recording status.
   LED Off : The currently selected slot is empty, with no recorded tracks.
   RED: The pedal is in REC or DUB status.
   BLUE : The pedal is in PLAY status.
   Blink in BLUE: The pedal is in STOP status.

3. Selector
   Rotate to select between 16 different saving slots.

4. LEVEL
   Rotate to adjust the volume level of playback tracks. 12 o’clock position for as loud as the real-time playing volume level; rotate to the far right position to get a +6dB volume boost.

5. THRESHOLD When AUTO REC is On, rotate the knob to adjust the threshold value of the AUTO REC. Rotate to the left side to get a low threshold value, the AUTO REC will be easy to be activated; rotate to the right side to a get high threshold value, and the AUDO REC will be difficult to be activated.

6. Bank selector
   Toggle to switch between three slot banks. Each bank has 16 saving slots.

7. INPUT
   1/4″mono audio input jack. Connect to the OUTPUT of the guitar or effects.

8. OUTPUT
   1/4″ mono audio output jack. Connect to the INPUT of the guitar amplifier or effects.

9. DC IN
   Power supply port. Please use 9V (center negative) power supply.

Instructions

1. Preparation
   • Plug in the power supply, and set up the connections of the guitar, effects, and amplifier.
   • Rotate the LEVEL to the 12 o’clock position
   • Select an empty slot
   • Turn On/Off the AUTO REC function, and set the THRESHOLD to a proper value.
   • Start playing
2. Recording Instructions

REC
Select an empty slot (the LED button is off), press the footswitch to start recording. The LED button will turn RED.

Notes : the first layer of the recording should be more than 1 second. If it is less than 1 second, the recording will be canceled automatically.

PLAY
Press the footswitch during REC, DUB, or STOP to enter the PLAY mode, and the LED button will turn BLUE.

STOP
Press the footswitch twice quickly during REC, DUB, or PLAY to STOP. The LED button will blink in BLUE.

DUB/CANCEL
If you would like to cancel DUB and restart the recording of the DUB, press and hold the footswitch for 1 second during DUB, the recorded track of the current layer will be deleted and the DUB will restart immediately, the LED will blink in RED for a few seconds.

UNDO/REDO
UNDO allows you to delete the last layer temporarily. When there are more than one layer is recorded, and the pedal is in PLAY status, press and hold the footswitch for 1 second to UNDO.

REDO allows you to restore the last layer. After UNDO, press and hold the footswitch for 1 second to REDO.

Notes : If a new layer is recorded after UNDO, then the UNDO layer will be deleted, and cannot be restored by

REDO.
CLEAR If you would like to delete all the tracks in the current slot, set it to STOP status, press, and hold the footswitch for 1 second. Then the LED button will be Off, as the current slot is empty.

Specifications

• Numofsavingslots: 48
• Maximum recording capacity of each slot: 10 minutes
• Sample rate/sample depth: 44.1kHz/24bit
• Input: 1/4” mono audio jack (impedance value: 470k ohm)
• Output: 1/4” mono audio jack (impedance value: 100 ohm)
• Power requirements: 9V 120mA, center negative (recommend to use the isolated power supply to avoid unexpected noise)
• Dimensions : 93.5(D)×42(W)×52mm(H)
• Weight: 157g
• Accessories: Owner’s manual

www.mooeraudio.com
SHENZHEN MOOER AUDIO CO. LTD 6F, Unit D, Jinghang Building, Liuxian 3rd Road, Bao’ an 71 District, Shenzhen, China. 518133 Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>