ELEMENTAL MACHINES EB1 Element-B VWR Incubator Installation Guide
- August 6, 2024
- ELEMENTAL MACHINES
Table of Contents
ELEMENTAL MACHINES EB1 Element-B VWR Incubator Installation Guide
Applicable VWR Incubator Models
✓ 51014991
✓ 51014992
✓ 50114902
✓ 50114903
✓ 51014995
✓ 51014996
✓ 51014900
✓ 51014901
Package Contents
✓ Element-B
✓ Connection Cable
Safety Information
Review and abide by the safety information found in the Element-B and VWR Incubator user manuals. Ensure compliance with your company safety best practices, which may include deenergizing equipment before working with electrical connections. Tidy connection cable to prevent tripping hazards.
Installation Instructions
Receiving the Shipment
-
If this is your first time setting up the Elemental Machines system, you will receive an email for your dashboard account verification. Save this email for when the devices arrive.
-
When devices are shipped, they will be added to your Elemental InsightsTM Dashboard with default names. When you first log in you will see all your devices with a ‘disconnected’ status.
-
When devices arrive, carefully remove the contents from the packaging. If any of the contents look damaged, please send a picture to help@elementalmachines.com.
-
If you have ordered multiple Element-B’s, ensure the Element-B being used is configured as Normally Closed (NC). This can be verified by checking the device label, the dashboard under `Machine Model’, or the packing list sent with your shipment.
a. Element-B’s can either be configured as Normally Closed (NC) or Normally Open (NO) by our team here at Elemental Machines. Different assets require different configurations. If you have ordered Element-B’s for multiple assets, you may have a mix and need to be aware of attaching the correctly configured device to the correct asset. -
Ensure there is an Elemental Machines Gateway set up in the vicinity of the Element-B.
a. Depending on your location and application, your Gateway type may vary. If you have a tablet Gateway, brief setup instructions are given in the element- specific user manual. If you have a Gateway Model GW2 or GW3, please follow the setup instructions in your Gateway, GW2 or GW3 User Manual
b. Note: `Vicinity’ is within wireless connection range. This is usually up to 30 meters but can depend on the lab’s layout.
Attaching Connection Cable to VWR Incubator -
Locate the RJ-11 telephone-style jack on the rear panel of the incubator.
-
Plug the RJ-11 connector end (shown in Figure 2) of the connection cable into the RJ-11 port on the incubator.
Attaching Connection Cable to Element -
Per your discretion, write the name and/or location of the equipment being monitored on the Element-B. This can be particularly helpful if multiple devices are being installed. Use of a Sharpie is recommended.
-
Plug the thermocouple end (Figure 3) of the connection cable into the Element-B.
a. Note: Ensure the (-) and (+) prongs of the thermocouple end are properly matched. -
Pull the battery tab on the Element-B.
Positioning the Element-B -
Determine where the Element-B should be placed so that it is not blocked, which allows a better wireless connection, and so that the connection cable is tidy.
-
Securely position the Element-B in the chosen location. The Element-B has magnets which make it easily mountable to magnetic surfaces.
a. Note: If applicable, an adhesive metal mounting plate available from EM may be used.
Programming Alerts -
Program alerts on the VWR Incubator. Refer to the VWR Incubator user manual for which alarm conditions the VWR Incubator can detect and how to set up alerts.
-
Set up alert rules on the Elemental InsightsTM Dashboard for the Element-B. Guidance on how to do so is available in the Support section of the dashboard.
NOTE: Alerts must be programmed on both the VWR Incubator and the Elemental InsightsTM Dashboard to receive threshold alerts through the Elemental Machines platform.
772-00006 rev 02 Element-B, EB1 EB2 VWR Incubator Installation Guide
Copyright © 2024 Elemental Machines
help@elementalmachines.com