Aerpro CHFO1C Steering Wheel Control Interface Owner’s Manual

: August 3, 2024
: Aerpro

Table of Contents

Aerpro CHFO1C Steering Wheel Control Interface
Product Specifications
Product Usage Instructions
FAQ
ABOUT THIS PRODUCT
WIRING COLOUR CODES
PRIOR TO INSTALLATION
TECHNICAL SUPPORT
STEERING WHEEL CONTROL FUNCTIONALITY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Aerpro CHFO1C Steering Wheel Control Interface

Product Specifications

Product Name: CHFO1C Steering Wheel Control Interface
Compatibility: Select Ford vehicles (Ford Fiesta 2002-2005,
Ford Fusion 2002-2005 with Visteon 4500 original stereo)
Features: Analogue Steering Wheel Control Interface

Product Usage Instructions

Before starting the installation process, please read the manual carefully. Ensure you have the necessary technical knowledge for installation. Choose a location free of moisture and away from heat sources. Use the correct tools to prevent damage to the vehicle or product.

Remove and disconnect the original head unit.
Connect the 12-way molex connector of the head unit patch lead to the interface.
Connect the opposite end of the head unit patch lead to the head unit steering wheel control input on the back of the aftermarket head unit. Note: This may be a 3.5mm jack plug or a wire input depending on the head unit brand.
Connect the 14-way molex connector to the interface.
Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit. For head units without an ISO connector, refer to Wiring Colour Codes on Pg. 2.
Connect the female vehicle-specific connectors on the harness to the male vehicle connector from the vehicle. Test the head unit for correct operation.

FAQ

Q: Can I install this product myself?
A: Installation requires technical knowledge, so it is recommended to seek professional help if you are not confident in your abilities.
Q: What should I do if the steering wheel controls are not working after installation?
A: Make sure you have connected all the cables correctly as per the instructions. If issues persist, contact technical support for assistance.

ABOUT THIS PRODUCT

CHFO1C

Analogue Steering Wheel Control Interface for Ford vehicles with Visteon 4500 original stereo.

WIRING COLOUR CODES

Purple Right Rear Speaker +
Purple/Black Right Rear Speaker –
Green Left Rear Speaker +
Green/Black Left Rear Speaker –
Grey Right Front Speaker +
Grey/Black Right Front Speaker –
White Left Front Speaker +
White/Black Left Front Speaker –
Yellow Permanent 12V
Black Ground
Red Ignition 12V

PRIOR TO INSTALLATION

Read the manual before installation.
Technical knowledge is necessary for installation.
The place of installation must be free of moisture and away from heat sources.
Please ensure that the correct tools are used during the installation to avoid damage to the vehicle or product.
Aerpro can not be held responsible for the installation of this product.

TECHNICAL SUPPORT

If you need assistance setting up or using your Aerpro product now or in the future, call Aerpro Support Australia TEL: 03 – 8587 8898 FAX: 03 – 8587 8866 Mon-Fri 9 am – 5 pm AEST.
If you would like to download a digital copy of this manual, or other Aerpro manuals/software, please visit the http://aerpro.com website.

FITTING GUIDE

Remove and disconnect the original head unit.
Connect the 12-way molex connector of the head unit patch lead (supplied separately) to the interface.
Connect the opposite end of the head unit patch lead to the head unit steering wheel control input on the back of the aftermarket head unit.
NB: This may be a 3.5mm jack plug or a wire input depending upon the head unit brand being fitted. Please see the head unit installation manual for further information on where to connect.
Important: This step must be completed before connecting power to the interface. Failure to so do may result in no steering wheel control function.
Connect the 14-way molex connector to the interface
Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit. For aftermarket head units without an ISO connector, please refer to “Wiring Colour Codes”
Connect the female vehicle-specific connectors on the harness to the male vehicle connector from the vehicle. Test head unit for correct operation.