Kindermann 7488000150 HDMI USB-HDBT3 Extender 4K60 Set Instruction Manual

Kindermann 7488000150 HDMI USB-HDBT3 Extender 4K60 Set

Foreword

Before using the product, read this manual carefully. The images shown in this manual are for reference only and may differ from the actual product.This manual is for reference only. Contact your local dealer for maintenance assistance. In a constant effort to improve the product, we reserve the right to change functions or parameters without prior notice or obligation. For the latest information, please contact your local Kindermann dealer.

Safety Instructions and precautions

•  Read the operating instructions carefully and keep them in a safe place.
•  Carefully unpack the unit and save the original packaging and packing materials for possible future shipment.
•  Follow basic safety precautions to reduce the risk of fire, reduce electric shock and injury to persons.
•  Never open or modify the unit. This may result in electric shock or burns.
•  The product may only be operated with safety extra-low voltage using the supplied power supply.
•  The use of consumables or parts that do not meet the product specifications may result in damage or malfunction.
•  Refer all servicing to qualified service personnel.
•  The system should only be stored and used in a dry environment.
•  Place the unit in a well-ventilated location to prevent damage from overheating.
•  Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power cord from the wall outlet before cleaning.
•  Unplug the power plug if you are not going to use the product for a long time.
•  Notes on the disposal of old equipment: The device may not be disposed of with the household waste, but must be returned via trade channels.
• Make sure that all components and accessories are included before installation.
•  All power switches, plugs, sockets and power cords must be insulated and secure.
•  All equipment must be connected before switching on.

Device description

The HDMI/USB-HDBT3 Extender 4K60 Set consists of a transmitter and a receiver. It can extend HDMI signals up to 4K60 and a distance up to 100 meters over a single CAT6A/CAT7 cable without using signal compression. It supports audio de-embedding, ARC, USB 2.0 high speed, IR- and RS232-signal pass-through as well as gigabit ethernet extension. The Power over Cable (PoC) feature allows the transmitter and the receiver to be powered from each other, only one power adapter is needed.

Features

•  Based on HDBaseT 3.0 technology
•  HDMI 2.0 compatible, supports a bandwidth up to 18Gbps to transmit video up to a resolution of 4K@60Hz 4:4:4 inlcuding HDR10 and Dolby Vision
•  HDCP 2.2 compliant, supports HDCP bypass
•  Extends 4K video signals up to 100 m over a single CAT6A/CAT7 cable without compression
•  Supports USB 2.0 high speed transmission (switch between host/device)
•  IR and RS232 pass-through control
•  Gigabit ethernet extension
•  Supports bi-directional 24V PoC
•  Supports audio de-embedding and ARC (Audio Return Channel)
•  HDMI loop out available on transmitter

Scope of delivery

•  1x Transmitter
•  1x Receiver
•  1x Power Adapter (24V DC 1.25A)
•  8x Plastic cushions
•  4x Mounting ears with 2 screws (each)
•  1x 3pin Euro block adapter
•  1x Adapter cable 3pin Euro block to 9pin SubD for RS232 communication, lenght 1,4 m
•  1x User manual

Note:
Please contact your distributor immediately if any damage or defect in the components is found.

Transmitter panel description

Front panel

1

| POWER LED| Lights green when power is applied. (Blinks in firmware upgrade mode.)

2

| LINK LED| Lights up when a HDBaseT link between transmitter and receiver has been established.

3

| ****

HDCP LED

| Lights up constantly when the video contains HDCP protected content, or blinks when the video isn’t HDCP protected.

4

| SOURCE LED| Lights up when a HDMI source is connected to HDMI input.
5| LOOPOUT LED| Lights up when devices are connected to HDMI source and HDMI loop out.

6

| ****

USB

| DIP switch to select DEVICE or HOST mode.

•    DEVICE : A USB device (e. g. USB flash drive, mouse, keyboard) is connected to the transmitter.

•    HOST : A HOST device (e. g. computer) is connected to the transmitter.

7

| ****

DEVICE

| ****

4 type-A USB 2.0 ports for devices (e. g. mouse, keyboard, camera)

8

| ****

HOST

| ****

Type-B USB 2.0 port for a host device (e. g. computer)

Rear panel

1

| ETHERNET| RJ45, connect to your IP network switch. Network data will be “tunneled” to/from the receivers ETHERNET port.

2

| ****

HDBT OUT

| ****

RJ45, connect to the HDBT input of the receiver. LINK LED lights up when a HDBaseT link has been established.

3| SOURCE| HDMI, connect to a source device.
4| LOOPOUT| HDMI, connect to a local display.

5

| ARC OUT| Toslink, for ARC audio output, connect an audio device (e. g. amplifier).

6

| AUDIO OUT| 3,5 mm jack, for audio de-embedding of the HDMI input signal, connect an audio device (e. g. amplifier).
7| IR IN| 3,5 mm jack, connect the IR receiver for IR pass-through.
8| IR OUT| 3,5 mm jack, connect the IR emitter for IR pass-through.

9

| ****

RS232

| Connect a RS232 control device (e. g. media control system) for pass- through or connect a device which shall be control- led by RS232 commands from the receiver side

(e. g. signal switcher).

10

| FIRMWARE UPGRADE BUTTON| ****

Please contact support.

11| DC 24V| Connector power supply unit.

Receiver panel  description

Front panel

1

| POWER LED| Lights green when power is applied. (Blinks in firmware upgrade mode.)

2

| LINK LED| Lights up when a HDBaseT link between transmitter and receiver has been established.

3

| ****

HDCP LED

| Lights up constantly when the video contains HDCP protected content, or blinks when the video isn’t HDCP protected.

4

| DISPLAY LED| Lights up when a device is connected to HDMI source and HDMI out.

5

| ****

ARC

| DIP switch for ARC mode selection.

•    HDMI : To receive the ARC input from the HDMI device connected to the “DISPLAY” of the receiver.

•    PASS : Supports CEC & ARC pass-through.

•    SPDIF : To receive the ARC input from the device con- nected to the ARC IN the receiver.

6

| ****

USB

| DIP switch to select DEVICE or HOST mode.

•    DEVICE : A device (e. g. USB drive, mouse, keyboard) is connected to the transmitter.

•    HOST : A HOST device (computer) is connected to the transmitter.

7| DEVICE| 4 type-A USB 2.0 ports for devices (e. g. mouse, keyboard, camera)
8| HOST| Type-B USB 2.0 port for a host device (e. g. computer)

Rear panel

1

| ****

ETHERNET

| RJ45, connect to your IP network switch. Network data will be “tunneled” to/from transmitters ETHERNET port.

2

| ****

HDBT IN

| RJ45, connect to HDBT input of the transmitter. LINK LED lights when a HDBaseT link has been established.
3| DISPLAY| HDMI, connect to the display device.
4| ARC IN| Toslink, ARC input, connect an audio source device (e. g. tuner).
5| IR IN| 3,5 mm jack, connect the IR receiver for IR pass-through.
6| IR OUT| 3,5 mm jack, connect the IR emitter for IR pass-through.

7

| ****

RS232

| Connect a RS232 control device (e. g. media control system) for pass- through or connect a device which shall be control- led by RS232 commands from the transmitter side

(e. g. signal switcher).

8

| FIRMWARE UPGRADE BUTTON| ****

Please contact support.

9| DC 24V| Connector power supply unit.

Connection Diagram

1.  When the ARC DIP switch is on “HDMI”, the display’s ARC audio can be transmitted back to the transmitter using the HDMI OUT connector of the receiver. It is available at ARC OUT and HDMI IN port of transmitter. CEC pass-through is not supported in this mode. Please note: The display as well as the selected input must supports ARC.

2.  When the ARC DIP switch is on “SPDIF”, audio can be transmitted back to the transmitter via ARC IN port of receiver. It is available at ARC OUT and HDMI IN port of transmitter.
   CEC pass-through is supported in this mode.

3.  When the ARC DIP switch is on “PASS”, the extenders can pass the ARC signal and support CEC pass-through. The display’s ARC audio can be transmitted back to the transmitter using the HDMI OUT connector of the receiver. It is available at ARC OUT and HDMI IN port of transmitter. The display as well as the selected input must supports ARC.

Note:
Please try to restart the extender if ARC function works abnormally.

Specifications

Video
Input (connector)| 1x HDMI (19-pin type-A female)| 1x HDBT (RJ45)
Input Resolution| Up to 4K@60Hz 4:4:4

Output (connector)

| 1x HDBT OUT (RJ45)

1x HDMI Loop out (19-pin type-A )female)

| 1x HDMI

(19-pin type-A female)

Output Resolution| Up to 4K@60Hz 4:4:4
Audio
Input (connector)| –| 1x ARC (Toslink)
Output| 1x ARC (Toslink),

1x Stereo audio (3,5 mm jack)

| –
Audio Format| Toslink (ARC): PCM, Dolby Digital, DTS 5.1CH 3.5mm jack: PCM 2CH
Frequency Response| 20Hz ~ 20KHz, ±3dB
Control / data communication

Interfaces (connector)

| 4x Device (type-A USB 2.0), 1x Host (type-B USB 2.0)

1x IR in (3.5mm jack) 1x IR out (3.5mm jack)

1x RS232 (3-pin terminal block) 1x ETHERNET (RJ45)

| 4x Device (type-A USB 2.0), 1x Host (type-B USB 2.0)

1x IR in (3.5mm jack) 1x IR out (3.5mm jack)

1x RS232 (3-pin terminal block) 1x ETHERNET (RJ45)

General
Bandwidth| 18Gbps
HDMI Standard| 2.0

HDCP Version

| Input: HDCP 2.2, HDCP 1.4 compliant Loopout: Follows the display’s HDCP version RX Output: Follows the source’s HDCP version
CEC| Pass-through (when ARC switch is selected to PASS or SPDIF)
Max. HDMI input and output cable length| 4K@60Hz 4:4:4 £ 5m, 4K@60Hz 4:2:0 £ 10m,

1080@60Hz £ 15m

Transmission Standard| HDBaseT
Transmission Distance| 4K/1080p – 100 meters
PoC| Bi-directional
Operation Temperature| -5 to +55°
Storage Temperature| -25 to +70°
Relative Humidity| 10% to 90%, Non-condensing
Power Supply| Input: 100V~240V AC; Output: 24V DC 1.25A
Power Consumption| max. 16W
Dimension (WHD)| 200 x 25 x 100 mm
Net Weight| 290g

Recommended cables

Note:
We recommend using of Ultra High-Speed HDMI or active HDMI cables supporting HDMI 2.0/18Gps for signal input and output to achieve the best results.

• 580900210x Ultra High-Speed HDMI cable, 1 to 3 m
•  58090030xx 4K60 HDMI active cable, 10 to 25 m
•  58090060xx AOC HDMI 2.0 cable, 7,5 to 50 m
• We recommend using high-quality CAT-6A or CAT7 cables with AWG 23/22 inner conductors.

CE declaration of conformity
Note:
The currently valid CE declaration can be viewed and downloaded at the following URL: https://shop.kindermann.de/erp/webshop/navigationPath/7488000150.html

References

• Kindermann GmbH
• HDMI/USB 2.0-HDBT3.0 4K60 Extender Set - Kindermann Webshop

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>