linovum Recessed Light Frame Instruction Manual
- October 30, 2023
- linovum
Table of Contents
Assembly/operating instructions / technical data for recessed light IP65 round
Intended use
This product is for lighting purposes only and: – be mounted radiating
downwards only – can be installed indoors and outdoors – protection type IP65,
suitable for use in damp areas – must not be exposed to strong mechanical
loads or heavy soiling – may not be operated after damp or dirty storage until
after a condition check – may not be changed or modified, otherwise the
operating permit and conformity will expire with immediate effect! It is not
allowed to remove the type plate.
If the aforementioned points are not observed, a short circuit or electric
shock may occur! There is danger to life!
General safety instructions
The complete installation may only be carried out by an authorized
electrician who is familiar with the applicable guidelines. Hereinafter
referred to as „qualified electrician“.
For safe handling of the product, the user must have read and understood the
installation/operating instructions completely before using the device for the
first time.
The product may only be used if it is alright. If the device or parts of it
are defective, it must be repaired by a qualified electrician.
Only use lamps/light sources approved by the manufacturer. The max. lamp
wattage in watts is not allowed be exceeded.
This product is not a toy and is not allowed be stored or used within the
reach of children.
Safe operation of the product is only guaranteed if these instructions are
followed. Therefore, keep these assembly/operating instructions. Linovum GmbH
accepts no liability if the instructions given here are not followed or the
lamp is subjected to improper use.
Assembly & configuration
Caution: The connecting cable must be disconnected from the power supply
before starting work (switch off the main switch/fuse)! Only use parts which
are supplied with the product or which are clearly marked as equipment!
Otherwise the product may not be sufficiently safe!
The cable routing shown in the illustrations is for simplified purposes only.
They in no way represent a recommendation for connection! The connection may
only be carried out by a qualified electrician.
Watch out for cables and gas and water pipes when drilling. Always route the
cable so that it does not touch the light. Fig.5.1
3.1 Assembly location
The product is suitable for installation in suspended ceilings. The product
may only be installed on a stable, tilt-resistant and level surface. The
minimum distances in Fig.5 must be observed! Sufficient air circulation must
be ensured! Do not cover the product under any circumstances, especially not
with insulating material! Fire hazard!
Keep a sufficient distance (0.5 m) from easily flammable objects (e.g.
curtains, drapes, etc.) and flammable materials!
Operation, bulb replacement, faults & disorders
Achtung: Disconnect the connecting cable from the power supply before
replacing lamps/light sources! Allow to cool down before replacing! Do not
cover! Covering with (e.g. towel) is a fire hazard!
Never look directly into the light source!
What to do in case of error?
In case of an error, the device must be switched off immediately. The product
may only be operated if it works correctly. The device may only be put back
into operation after it has been checked by a qualified electrician!
This is the case if:
- there is visible damage,
- the product is not working corrctly,
- there is smoke, steam, or audible crackling noises,
- overheating can be detected.
Caution: There is a danger to life – repairs to the product or work on
parts carrying mains voltage may only be carried out by qualified
electricians.
The product must not be covered under any circumstances. Air circulation
must be guaranteed. Nothing may be attached or hung on the product, especially
no decoration.
Cleaning & care instructions
The product may only be wiped dry or carefully with a slightly damp and lint- free cloth. The product is not allowed to be removed for this purpose. Do not use abrasive or sharp objects or aggressive cleaning agents. Do not use solvents.
Assembly instructions
- Measure and cut out the cutout (Ø see technical data). Fig.1
- Loosen the front of the frame with a left turn from the front. Fig.5.2.
- Insert the bulb from the front and secure it with the snap ring.
- Now take the front and fix it with a clockwise rotation. Fig.5.2.
- Connect the lampholder or LED module directly to the mains cable – e.g. luster terminal etc. Fig.2 / 3.a
- Press the spring clips upwards and insert the lamp into the cutout. Fig.3.b + c
- Suitable for ceilings from 3-20mm thick. Fig.4
- Make sure that the product cannot fall down after assembly!
- The product is now ready for use.
Technical data
Can be installed indoors and outdoors
| Type: | Recessed ceiling rame |
|---|---|
| Model: | 810002008 / 810002009 |
| Protection type: | IP65 |
| Voltage: | 12 V oder 230 V ~ 50 Hz |
| Material: | Brushed steel / glas |
| Light source: | MR16, GU10 or LED-Modul – max. 15 W |
| Measurements: | Ø 85 mm |
| Installation depth without light source: | 27 mm |
| Cutout: | 56-69 mm |
| Colour: | White /silver |
Important information
| Distance to illuminated objects min. 0.5m
---|---
| Protection class II
| Installation only by qualified electrician
| Disconnect the device from the mains power before starting any work
| Do not cover with insulating material
Notes on use indoors & outdoors
Protection type IP20 & IP23 – Use only indoors and dry, i.e. do not use in
damp or dirty rooms and in areas of high humidity.
Protection type IP44 & IP6x – Can be used indoors and outdoors.
Web: www.linovum.de
Satisfied with your product?
Then we look forward to your product review in our online store, on Amazon or
eBay!
Disposal instructions
Make sure to dispose packaging in accordance with the applicable guidelines of
your local authority. Devices marked with the crossed-out waste garbage do not
belong in the household waste! You are obliged to hand in these devices at one
of the free collection points in your municipality. You can obtain more
information from your local authority, the relevant town hall or a local or
regional waste disposal company.
Keep packaging material and small parts away from children and animals.
Danger of suffocation!
linovum GmbH – Am Krozinger Weg 4, 79189 Bad Krozingen, Germany
E-Mail: service@linovum.de – Phone: 07633 –
9393-841 – www.linovum.de
**** Vers. 04/2019