peerless-AV Seamless Kitted Universal Series Installation Guide
- August 2, 2024
- Peerless-AV
Table of Contents
peerless-AV Seamless Kitted Universal Series
Specifications
- Product Name : SEAMLESS Kitted Universal Series
- Model Number : 146-9082-5
- Date: 2024-06-25
Product Information
The SEAMLESS Kitted Universal Series is a versatile mounting solution designed for a variety of display models. It comes with a comprehensive set of parts and tools required for assembly.
Parts List
- A latch assembly
- 4′ horizontal extrusion
- Wall plate
- Depth adjustment bracket
- Connector plate
Tools Needed for Assembly
- 5/32 (4mm) allen wrench
- 3/8 (10mm) allen wrench
- 5mm, 6mm, 8mm allen keys
Product Usage Instructions
Step 1: Parts Check
Before beginning assembly, ensure you have all the parts listed in the
parts list included with your model.
Step 2: Screw Tightening
To properly tighten screws, follow these guidelines:
- Tighten until the screw head makes contact.
- Then tighten another 1/2 turn. Do not overtighten screws.
- Screws must get at least three full turns and fit snugly.
- Wear anti-static gloves while handling the screws.
Step 3: Assembly Process
Follow the provided formula to calculate the A dimension if your display
model is not listed in the table. Use the dimensions provided to locate the
mount on the wall with proper clearance.
WARNING: This product is designed to be installed on plywood walls.
Hardware is included for plywood installation. This product is designed to be
installed on flat, unobstructed, vertical walls. Do not install on curved or
angled
walls. Before installing make sure the supporting surface will support the
combined load of the equipment and hardware. Screws must be tightly secured.
Do not overtighten screws or damage can occur and product may fail. Never
exceed the Maximum Load Capacity. Always use an assistant or mechanical
lifting equipment to safely lift and position equipment. This product is
intended for indoor use only. Use of this product outdoors could lead to
product failure or personal injury. Be careful not to pinch fingers when
operating the mount. For support please call customer care at
1-800-865-2112.
Symbols
Tools Needed for Assembly
To properly tighten screws: Tighten until screw head makes contact, then tighten another 1/2 turn. Do not overtighten screws
Parts (Before beginning, make sure you have all parts shown below). *Refer to parts list included with your model
Parts List
Description
Parts
INSTALLATION INSTRUCTION
-
If display model is not listed on table in the following step, use formula provided to calculate the “A” dimension.
-
Y* = bottom of display tile to top pair of mounting holes on back of display.
-
See table and drawing below for dimensions that will locate mount on the wall.
Compatible Display
| Bottom of video wall to top of first wall plate
Dimension A
| Side of video wall to center of first wall plate
Dimension B
| Center to center
wall plates Dimension C
|
System Depth Range Dimension D
---|---|---|---|---
Absen A27- V3| 13.59″ (345mm)| 12″ (305mm)| 24″ (610mm)|
4.49″-5.24″ (114-133mm)
Absen Acclaim| 13.59″ (345mm)| 12″ (305mm)| 24″ (610mm)| 4.67″-5.42″
(119-138mm)
Absen CL V2| 13.59″ (345mm)| 12″ (305mm)| 24″ (610mm)| 4.70″-5.45″
(119-138mm)
Absen KL| 20.22″ (514mm)| 12.60″ (320mm)| 25.19″ (640mm)| 5.08″-5.83″
(129-148mm)
Absen KL II| 15.58″ (396mm)| 12.60″ (320mm)| 25.20″ (640mm)| 5.31″-6.06″
(135-154mm)
Absen KLCOB V2| 15.1″ (383mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.28″-5.03″ (109-128mm)
Absen NX 240X540| 22.94″ (583mm)| 4.72″ (120mm)| 9.45″ (240mm)|
4.45″-5.2″ (113-132mm)
Absen NX 960X540| 22.94″ (583mm)| 18.9″ (480mm)| 37.8″ (960mm)|
4.45″-5.2″ (113-132mm)
AOTO CV| 14.81″ (376mm)| 11.81″ (300mm)| 23.62″ (600mm)| 4.21″-4.96″
(107-126mm)
Barco NT| 14.97″ (380mm)| 11.81″ (300mm)| 23.62″ (600mm)| 4.29″-5.04″
(109-128mm)
Barco XT| 15.05″ (382mm)| 12″ (305mm)| 24″ (610mm)| 5.51″-6.26″
(140-159mm)
Blue Square BSX| 15.03″ (382mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.12″-4.87″ (105-124mm)
BOE BYH-B| 14.82″ (376mm)| 11.81″ (300mm)| 23.62″ (600mm)| 4.59″-5.34″
(117-136mm)
Christie CSII| 14.50″ (368mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.2″-4.95″ (107-126mm)
Christie CSIII| 14.50″ (368mm)| 11.81″ (300mm)| 23.62″ (600mm)|
3.88″-4.63″ (99-118mm)
DVS DioPlex 960×960| 39.18″ (995mm)| 18.9″ (480mm)| 37.8″ (960mm)|
6.25″-7″ (159-178mm)
DVS DioPlex HD 500×1000| 40.79″ (1036mm)| 9.84″ (250mm)| 19.69″ (500mm)|
19.69″-6.7″ (151-170mm)
Fabulux T Series (1000×500)| 21.11″ (536mm)| 19.69″ (500mm)| 39.37″
(1000mm)| 4.01″-4.76″ (102-121mm)
HIK CWF/CWF III / CWFH III| 14.87″ (378mm)| 11.81″ (300mm)| 23.62″
(600mm)| 4.7″-5.45″ (119-139mm)
HIK ZWDH| 15.03″ (382mm)| 11.81″ (300mm)| 23.62″ (600mm)| 4.53″-5.28″
(115-134mm)
Imaginis 1.x-Mod| 14.59″ (371mm)| 11.81″ (300mm)| 23.62″ (600mm)|
5.02″-5.77″ (128-147mm)
InfiLED EZ Series| 20.89″ (531mm)| 9.84″ (250mm)| 19.69″ (500mm)|
5.71″-6.46″ (145-164mm)
InfiLED WK| 14.39″ (365mm)| 11.81″ (300mm)| 23.62″ (600mm)| 3.89″-4.64″
(99-118mm)
InfiLED WP| 14.39″ (365mm)| 11.81″ (300mm)| 23.62″ (600mm)| 3.91″-4.66″
(99-118mm)
InfiLED WT| 14.39″ (365mm)| 11.81″ (300mm)| 23.62″ (600mm)| 3.91″-4.66″
(99-118mm)
Jupiter ZAVUS XP-P0.7| 11.45″ (291mm)| 9.45″ (240mm)| 18.9″ (480mm)|
3.84″-4.59″ (98-117mm)
Jupiter ZAVUS XP-P0.9/1.2| 13.71″ (348mm)| 11.81″ (300mm)| 23.62″
(600mm)| 3.84″-4.59″ (98-117mm)
Just Video 05-IND-A01| 14.42″ (366mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.27″-5.02″ (109-128mm)
LED Studio SOLARIS| 14.89″ (378mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.29″-5.04″ (109-128mm)
Leyard GF| 19.87″ (505mm)| 12.6″ (320mm)| 25.2″ (640mm)| 5.65″-6.4″
(144-163mm)
Leyard VDS| 14.89″ (378mm)| 11.81″ (300mm)| 23.62″ (600mm)| 4.46″-5.21″
(113-132mm)
LG LSBB (GD)| 15.14″ (384mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.92″-5.67″ (125-144mm)
LG LSBC| 40.78″ (1036mm)| 9.84″ (250mm)| 19.69″ (500mm)| 5.42″-6.17″
(138-157mm)
LG LSCA (1000 TALL) GK| 40.66″ (1033mm)| 9.84″ (250mm)| 19.69″ (500mm)|
5.3″-6.05″ (135-154mm)
LG LSCA (1000 TALL) GN| 40.66″ (1033mm)| 9.84″ (250mm)| 19.69″ (500mm)|
5.42″-6.17″ (138-157mm)
LG LSCA (500 TALL) GK2| 20.97″ (533mm)| 9.84″ (250mm)| 19.69″ (500mm)|
5.3″-6.05″ (135-154mm)
LG LSCB| 14.39″ (365mm)| 11.81″ (300mm)| 23.62″ (600mm)| 3.91″-4.66″
(99-118mm)
---|---|---|---|---
LG LSCB Portrait| 25.07″ (637mm)| 6.64″ (169mm)| 13.29″ (338mm)|
3.91″-4.66″ (99-118mm)
LG LWBC (1000 TALL) GD| 40.78″ (1036mm)| 9.84″ (250mm)| 19.69″ (500mm)|
5.38″-6.13″ (137-156mm)
LG LWBC (750 TALL) DD| 30.93″ (786mm)| 9.84″ (250mm)| 19.69″ (500mm)|
5.46″-6.21″ (139-158mm)
LG LSAC| 23.55″ (598mm)| 23.62″ (600mm)| 47.24″ (1200mm)| 4.75″-5.5″
(121-140mm)
LG LSBE| 14.89″ (378mm)| 11.81″ (300mm)| 23.62″ (600mm)| 5.55″-6.3″
(141-160mm)
LG LSBF| 28.17″ (716mm)| 23.62″ (600mm)| 47.24″ (1200mm)| 5.57″-6.32″
(142-161mm)
Linsin MA 640X480| 19.91″ (506mm)| 12.6″ (320mm)| 25.2″ (640mm)| TBD
Linsin N169| 15.07″ (383mm)| 11.81″ (300mm)| 23.62″ (600mm)| TBD
Macropix Imaginis J| 14.69″ (373mm)| 11.81″ (300mm)| 23.62″ (600mm)| TBD
Macropix Mobilis FT| 21.11″ (536mm)| 19.69″ (500mm)| 39.37″ (1000mm)|
4.11″-4.86″ (104-124mm)
MAXHUB M27| 14.91″ (379mm)| 12.01″ (305mm)| 24.02″ (610mm)| 3.96″-4.71″
(101-120mm)
Mobilis FT2.6 1000×500| 21.11″ (536mm)| 19.69″ (500mm)| 39.37″ (1000mm)|
4.01″-4.76″ (102-121mm)
Mobilis FT2.6 500×500| 21.11″ (536mm)| 9.84″ (250mm)| 19.69″ (500mm)|
4.01″-4.76″ (102-121mm)
Mobilis F2.6XRMBV-MOD 500×750| 30.95″ (786mm)| 9.84″ (250mm)|
19.69″ (500mm)| 5.15″-5.90″ (131-150mm)
NEC E Series| 14.94″ (379mm)| 11.81″ (300mm)| 23.62″ (600mm)|
3.88″-4.63″ (99-118mm)
NEC FAFE| 14.91″ (379mm)| 11.81″ (300mm)| 23.62″ (600mm)| 4.67″-5.42″
(119-138mm)
Panavisual CS261| 20.89″ (531mm)| 9.84″ (250mm)| 19.69″ (500mm)|
5.1″-5.85″ (130-149mm)
Panavisual CU181| 20.11″ (511mm)| 9.45″ (240mm)| 18.90″ (480mm)|
4.75″-5.5″ (121-140mm)
Philips 27BDL6000| 15.07″ (383mm)| 11.97″ (304mm)| 23.94″ (608mm)|
5.06″-5.81″ (129-148mm)
Philips 27BDL9000| 15.07″ (383mm)| 11.97″ (304mm)| 23.94″ (608mm)|
4.86″-5.61″ (123-142mm)
Philips 28HDL5000| 21.21″ (539mm)| 9.84″ (250mm)| 19.69″ (500mm)|
4.39″-5.14″ (112-131mm)
Philips 44HDL5000| 40.89″ (1039mm)| 9.84″ (250mm)| 19.69″ (500mm)|
4.47″-5.22″ (114-133mm)
Planar DLP-27| 15″ (381mm)| 11.91″ (302mm)| 23.81″ (605mm)| 5.31″-6.06″
(135-154mm)
Planar DLP-36| 28.39″ (721mm)| 11.91″ (302mm)| 23.81″ (605mm)|
5.31″-6.06″ (135-154mm)
Planar TVF| 14.99″ (381mm)| 11.91″ (302mm)| 23.81″ (605mm)| 5.1″-5.85″
(130-149mm)
QST Quanta| 14.39″ (365mm)| 11.81″ (300mm)| 23.62″ (600mm)| 4.18″-4.93″
(106-125mm)
Samsung IEC| 14.69″ (373mm)| 11.81″ (300mm)| 23.62″ (600mm)| 4.24″-4.99″
(108-127mm)
Samsung IEC-L| 14.69″ (373mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.24″-4.99″ (108-127mm)
SBC CRYSTAL| 15.06″ (382mm)| 11.81″ (300mm)| 23.62″ (600mm)| 4.2″-4.95″
(107-126mm)
SNA VST| 18.93″ (481mm)| 7.87″ (200mm)| 15.75″ (400mm)| 4.55″-5.3″
(116-135mm)
SNA VTI 400X450| 19.42″ (493mm)| 7.87″ (200mm)| 15.75″ (400mm)|
5.3″-6.05″ (135-154mm)
Sony BH/CH (Cancun)| 13.59″ (345mm)| 12.01″ (305mm)| 24.02″ (610mm)|
5.46″-6.21″ (139-158mm)
Sony Crystal B &C| 14.87″ (378mm)| 11.97″ (304mm)| 23.94″ (608mm)|
4.65″-5.4″ (118-137mm)
Sony Verona| 21.60″ (549mm)| 9.84″ (250mm)| 19.69″ (500mm)| 6.4″-7.15″
(163-182mm)
Stratech ST150LI-PRO| 28.18″ (716mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.5″-5.25″ (114-133mm)
Unilumin UHWII| 15.11″ (384mm)| 12.01″ (305mm)| 24.02″ (610mm)|
5.38″-6.13″ (137-156mm)
Unilumin UHWIII| 14.97″ (380mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.24″-4.99″ (108-127mm)
Unilumin ULWIII| 14.89″ (378mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.49″-5.24″ (114-133mm)
Unilumin Umini| 15.09″ (383mm)| 11.81″ (300mm)| 23.62″ (600mm)|
5.65″-6.4″ (144-163mm)
Unilumin UMINI III| 14.89″ (378mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.33″-5.08″ (110-129mm)
Unilumin Upanel II| 15.11″ (384mm)| 12.01″ (305mm)| 24.02″ (610mm)|
5.42″-6.17″ (138-157mm)
Unilumin UpanelS| 15.05″ (382mm)| 12.01″ (305mm)| 24.02″ (610mm)|
5.51″-6.26″ (140-159mm)
Unilumin UpanelSII| 15.11″ (384mm)| 12.01″ (305mm)| 24.02″ (610mm)|
5.3″-6.05″ (135-154mm)
Unilumin Uslim II (500X1000)| 40.97″ (1041mm)| 9.84″ (250mm)| 19.69″
(500mm)| 4.26″-5.01″ (108-127mm)
Unilumin Uslim II (500X250)| 11.45″ (291mm)| 9.84″ (250mm)| 19.69″
(500mm)| 4.26″-5.01″ (108-127mm)
Unilumin Uslim II (500X500)| 21.29″ (541mm)| 9.84″ (250mm)| 19.69″
(500mm)| 4.26″-5.01″ (108-127mm)
Unilumin UTWIII| 22.86″ (581mm)| 18.90″ (480mm)| 37.80″ (960mm)|
3.85″-4.6″ (98-117mm)
Vanguard Axion 600×337.5| 14.89″ (378mm)| 11.81″ (300mm)| 23.62″
(600mm)| 5″-5.75″ (127-146mm)
Vanguard Axion 300×337.5| 14.89″ (378mm)| 5.91″ (150mm)| 11.81″
(300mm)| 5″-5.75″ (127-146mm)
Vanguard Invictus 600×337.5| 13.71″ (348mm)| 11.81″ (300mm)| 23.62″
(600mm)| 3.86″-4.61″ (98-117mm)
Vanguard LA 43″| 22.47″ (571mm)| 18.90″ (480mm)| 37.80″ (960mm)|
4.27″-5.02″ (109-128mm)
Vanguard LA 55″| 28.05″ (712mm)| 23.86″ (606mm)| 47.72″
(1212mm)| 4.29″-5.04″ (109-128mm)
Vanguard Sirius 1200×675| 27″ (686mm)| 23.62″ (600mm)| 27.24″ (1200mm)|
3.86″-4.61″ (98-117mm)
Vanguard Zirconium 500×250| 11.64″ (296mm)| 9.84″ (250mm)| 19.69″
(500mm)| 4.38″-5.13″ (111-130mm)
Vanguard Zirconium 750×250| 11.64″ (296mm)| 14.76″ (375mm)| 29.53″
(750mm)| 4.38″-5.13″ (111-130mm)
Vanguard Zirconium 1000×250| 11.64″ (296mm)| 19.69″ (500mm)| 39.37″
(1000mm)| 4.38″-5.13″ (111-130mm)
WORTH IFA 1000X250| 11.17″ (284mm)| 19.69″ (500mm)| 39.37″ (1000mm)|
3.92″-4.67″ (100-119mm)
WORTH UHD 600X337.5| 14.89″ (378mm)| 11.81″ (300mm)| 23.62″ (600mm)|
4.31″-5.06″ (110-129mm)
Optional : connecting two horizontal extrusions.
Determine the required extrusion length with the following extrusion cut to length formula:
Now that the extrusions are cut to length, separate the extrusions and slide wall plates onto extrusions and tighten with the wall plate fully extended (one wall plate per display unless the display is >960mm wide, in which case there will be two wall plates per display).
WARNING: When installing Peerless wall mounts on a wood stud wall covered
with plywood, verify that the wood studs are a minimum of 2″ x 4″ nominal size
and plywood is a minimum Grade BC, 1/2″ (13mm) thick. Plywood may be covered
by gypsum board (drywall) up to 5/8″ thick.
Install the bottom row, first extrusion assembly, on the laser line per table
(step 1), dimension “A”. Install additional bottom row extrusions one at a
time using connector plates to join extrusions. Drill mounting holes and
install screws and washers with top edge of the wall plates on the laser line.
Determine the height of the display being mounted and locate the same dimension on the front of the spacer. If the display height is above 540mm, add the spacer extension. If display height is not listed on the spacer, measure the display to set custom spacing.
Add the extension for displays taller than 540mm. Move the spacer bracket and clamp to the lower extension
Move spacer bracket and clamp to the desired display height. This may require adjusting the pins of spacer bracket
Optional: Remove and replace pins to align with correct display height.
If the display height is not listed on the spacer, measure the display to set the spacing
Install remaining extrusions using the spacers. Clamp the upper spacer jaw assembly to an uninstalled extrusion assembly. Clamp the bottom spacer jaw assembly to the installed extrusion. Vertically align extrusions with a laser. Drill mounting holes into supporting surface and install wall plates to the wall.
- Loosen clamps and remove spacers.
- Repeat the steps above to install the next extrusion.
- Engage and secure the connecter plate to mounted extrusions. Secure wall plates to the wall. Remove the spacer when extrusions are fully secured.
Set a laser level so that it is parallel to the mounting surface (wall). Measure the face of the extrusion so that all points of the extrusion are the same distance from the laser line, creating one flat plane across the face of the mount. Tighten screws Double check using a straight edge to span three extrusions. Adjust low and high spots as needed.
Hook display cabinets onto horizontal extrusion, adjust the height to level and join cabinets together using the connecting system. Adjust the plumb, close the latch, then run cables one at a time starting from left to right.
Hook display cabinets onto horizontal extrusion, adjust height to level and
join cabinets together using connecting system. Close latch, then run cables
one at a time starting from left to right.
To remove, start from the top right. Open latch assemblies, disconnect cables,
separate cabinets and remove displays one at a time.
Warranty
Peerless-AV
- 2300 White Oak Circle
- Aurora, IL 60502, USA
- info@peerless-av.com
- 800-865-2112
- 630-375-5100
Peerless-AV EMEA
- Unit 2, Curo Park
- Frogmore, St. Albans,
- Hertfordshire, AL2 2DD
- United Kingdom
- +44 (0) 1923 200 100
Peerless-AV B.V.
- Papendorpseweg 75
- 3528 BJ Utrecht
- The Netherlands
- +31 (0) 70 770 8037
Peerless-AV Latin America
- Av. de las Industrias 413
- Parque Industrial Escobedo
- General Escobedo N.L.,
- México 66062
- +52 (81) 8384-8300
2024 Peerless Industries, Inc. Peerless-AV® is a registered trademark of Peerless Industries, Inc. All rights reserved. Other parties’ marks are the property of their respective owners.
FAQ
- Q: What should I do if I encounter missing parts during assembly?
- A: If you find any missing parts, please contact our customer support for assistance. Provide your model number and purchase date for quick resolution.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>